Search Documents

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

By Robert J. Willard

This chapter includes tables for 1982 that were not available in time for publication of the 1982 Minerals Yearbook, but does not include corresponding tables for 1983. The value of raw nonfuel minerals produced in the United States during 1988 was estimated at $21.1 billion, an increase of $1.5 billion over the value for 1982. This is a reversal of last year's downturn in value from that of 1981, which was the only decrease noted since 1971; hence, an overall trend of increasing values has been maintained for 12 years, except for 1982. Although the reversal is a basis for cautious economic optimism, it is tempered by continued problems in the domestic mining industry: inadequate funds for capital investment and competition with other countries that have lower production costs. Output of metal commodities in 1983 increased for 8 out of 21 metals, and metal values, in general, increased for 9 of the metals. Output of nonmetal commodities was mixed, with 24 nonmetals showing increases, 20 showing decreases, and 2 unchanged. Nonmetal values were also mixed in 1982: 25 showed increases, 20 declined, and 1 was unchanged. Improvements in the international metals market have not been forthcoming because of the continued depressed prices for major metals. Governments in foreign producing countries have been concerned with maintaining employment and continuing foreign exchange flows through mineral exports. Consequently, the excess of supply in the face of shrinking demand brought downward pressure on metal prices in general, except for the precious metals. On the domestic front, this situation means U.S. mining companies must become even more cost efficient. The major trend in the mining industry in 1983 was to cut costs further, reduce or stabilize total production, reduce outlays for major capital equipment, modify existing systems and equipment, and streamline operations. Most of the accomplishments reported herein reflect this trend.

Jan 1, 1984

By S. R. Borrowman

Mill tailings from conventional uranium extraction processes contain nearly all of the radium originally in the ore. Such tailings require controlled storage in perpetuity to safeguard the surrounding environment from radioactive contamination. Alternatives to controlled storage of the tailings are (1) removal of the radium from the tailings for separate storage or use or (2) removal of the radium when processing the uranium ore. In laboratory tests conducted by the Federal Bureau of Mines, radium was leached from tailings using either hydrochloric acid or ethylenediamine tetraacetic acid. A hydrochloric acid leaching method was used to extract both radium and uranium from the ore to yield tailings containing less radium than those produced by either conventional sulfuric acid or alkaline leaching processes. From 77 to 94 percent of the radium in mill tailings was concentrated by sedimentation in slime fractions representing nearly 25 weight-percent of the original sample.

Jan 1, 1975

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968

By S. D. Maksimovic

The use of vertical surface degasification boreholes with bleeder systems and the use of a timbered bleeder system to degasify gob areas were studied by the Bureau of Mines. This report describes three gob degasification studies conducted in the Pittsburgh coalbed. One study was conducted to determine the number of panels degasified with one large borehole. The study showed that the borehole provided degasification for three panels. Another study was conducted during the retreat of a 35-acre panel with a single-entry and a two-entry bleeder system and a large surface borehole. A major portion of methane emitted from the panel was carried away by the bore-hole, leaving the bleeder entries relatively free of methane. The last study was made to determine the effectiveness of a timbered bleeder system. The bleeder entries successfully degasified the gob area when enough entries were available and adequate pressure was available to force the air through roof falls.

Jan 1, 1980

By N. S. Dalal, N. Leelarasamee, V. Castranova, K. Van Dyke, V. Vallyathan

"INTRODCICTIONSilicosis is the chronic fibrosing disease of the lungs caused by the inhalation of crystalline silica. However, inhalation of crystalline silica, may induce three distinctly different disease patterns; i.e., chrome silicosis, accelerated silicosis, and acute silicosis. These three disease patterns differ in their pathologic characteristics, clinical symptoms, onset of disease, and mortality. Many studies in the past have focused on the elucidation of mechanisms involved in the development of chrome silicosis. We recently reported that freshly fractured silica has surface properties that could make it more reactive with lung tissue than aged silica, and that this unique reactivity of freshly fractured silica may be involved in the pathogenesis of acute silicosis (Dalal et al., 1986; Vallyathan et al., 1988; Shi et II., 1988). Because freshly fractured silica could contain some moieties in an ""excited state,"" due to the breakage of silicon oxygen bonds, we postulated that the de-excitation of these moieties could produce light which could be monitored by a luminescence measurement technique. In addition, if this ""excited state'' of silica could trigger a greater biologic response by phagocytic cells, this activation could be monitored by a chemiluminescence technique in the presence of appropriate enhancers.This investigation describes for the first time the use of luminescence in the study of freshly fractured silica and its properties. Enhanced biologic reactivity of the freshly fractured silica with alveolar macrophages was monitored by the chemiluminescence technique.MATERIALS AND METHODSNative silica was obtained from the dust bank of the GenericRespirable Dust Technology Center, Pennsylvania State University, State College, PA, and ground for 3~ min in an agate ball mill. It was then sieved through a 20 micron mesh filter and used within 1 O min as fresh silica or stored in glass bottles for aging. X-ray energy spectrometry and X-ray powder diffraction studies on representative samples were made to confirm the mineralogic purity. All the silica samples were found to be 99 % pure with minimal detectable conlamination by metal ions."

Jan 1, 1990

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By B. T. McClure

Oxidizing catalytic converters are sometimes used by underground mine operators as an emission control device to reduce odor, hydrocarbon (HC), and carbon monoxide (CO) emissions from diesel equipment. The objectives of this report are to quantitatively assess the effects of catalytic converters on diesel exhaust emissions and to make recommendations for their use. Information in this report is from a literature survey and contract research supported by the Bureau of Mines. Catalytic converters are effective in reducing CO, HC, and odors when the exhaust temperature is high enough so that the converter remains above 250° C. Converter temperature is dependent upon engine duty cycle. Catalytic converters increse sulfate emissions and slightly in- crease oxides of nitrogen (NOx) emissions. If low sulfur fuels are not used, the increase in sulfate and nitrogen dioxide (NO2) emissions can offset any advantages of the catalytic converter as measured by the emissions quality index (EQI). In addition, in vitro bioassays have shown that catalytic converters produce soluble organic compounds, which have increased mutagenic activity with respect to untreated exhaust. Based upon criteria recommended by a joint Canadian-United States research panel, catalytic converters should only be used in special circumstances in underground mines. Vehicles equipped with catalytic converters should operate under moderate to heavy load conditions, and use fuel with a sulfur content less than 0.1 pct.

Jan 1, 1988

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By A. A. Sonnek

A simple, portable helium analyzer was developed primarily for field use. Its utility lies in making preliminary surveys before exact analyses are required. The analyzer is based upon chromatographic principles; that is, separation of gas mixtures resulting from variable retention times of the components with respect to a separation medium (column-packing material). It uses thermistors for sensing detectors, a dry battery as source of power, and a micro-ammeter for indicating helium concentration. The absolute accuracy of the instrument depends upon the recency and care with which the instrument is calibrated with a standard gas. The unknown gas should be analyzed immediately after calibration, and another calibration should be made before another unknown sample is analyzed. The instrument is simple to operate, requiring approximately 15 minutes, after calibration, to determine the helium content of a natural gas sample. Although developed primarily for helium determination, the analyzer possibly can be used for other analyses that can be performed at ambient temperatures.

Jan 1, 1965

By C. P. Fang, V. A. Marple, K. L. Rubow

"Studies of the flow fields and particle impaction characteristics are more complicated in multi-nozzle impactors than in single-nozzle impactors, since the jets of air must penetrate cross-flowing air to impinge on the impaction plate. Results of heat and mass transfer analysis are employed to describe the cross-flow pattern in multi-nozzle impactors. A cross-flow parameter has been derived to predict the deflection of the air jet by the cross-flow. This parameter is expressed as a function of the geometric parameters for the multi-nozzle impactor. DnN 4D,, where N is the number of nozzles, Dn the nozzle diameter and D, the nozzle cluster diameter. Empirical particle collection data show that multi-nozzle impactors operate satisfactorily, if the cross-flow parameter is less than a critical value of 1.2. Impactors operating with a cross-flow parameter larger than this critical value are shown to possess poor particle collection characteristics.Inertial impactors of many designs have been used for sampling aerosol particles. Impactors can be single stage, consisting of a nozzle and an impaction plate, or a cascade impactor with several stages in series. The simplest design for a stage is a single nozzle with a flat impaction plate. However, many designs use stages with multiple nozzles of identical size, which allows for compact impactors to be designed at rather substantial flow rates and moderate pressure drops.Nearly all of the theoretical work, and much of the experimental work, has been performed on single-nozzle impactors. The results of single-nozzle impactor analysis are often applied to multiple-nozzle impactors, which are assumed to be a group of individual nozzles, each operating as though they were single nozzles. However, an important fact is often ignored: the interaction of flow from adjacent nozzles can change not only the fluid mechanics in the impaction region, but also the locations of the jet stagnation points, and the impaction characteristics of each nozzle.The effect of multiple nozzles on the particle collection characteristics of impactors has been studied by a few investigators. May (1964), Fletch et al. (1967), Friedrichs (1968), and Vaughan (1986) reported that the quantity of particles in deposits of nozzles in the first two stages of the Andersen multi-nozzle cascade impactor were not equal. The inner deposits appeared to contain fewer particles than the outer ones. However, Vaughan (1986) in addition showed that many of the deposits in the outer three rows were missing on the first stage, even though the outer deposits that were present were larger than the inner deposits.May (1964) conducted experiments and explained the phenomenon of smaller deposits near the center than near the edge. He noted that in Andersen cascade impactors the air issuing from the nozzles moves radially outward along the narrow channel between the nozzle plate and the impaction plate. This flow at 28.31min -1 created a pressure difference of about 1 mm water between the inner and outer sections of the channel. The effect was most pronounced in the first two stages, where the pressure drop across the nozzles was also about 1 mm water. Here, the flow velocities in the nozzles, and hence the deposits, were smallest at the center and increased toward the periphery of the impaction plate. since the pressure drop across the nozzles was the smallest at the center and a maximum at the periphery. This effect was negligible in the lower stages because of a larger pressure drop across the nozzles. According to May (1964), this effect could be eliminated by increasing the nozzle-to-impaction-plate distance to three nozzle diameters and improving the nozzle arrangement to allow air flow to escape to the periphery more easily."

Mar 1, 1992

By A. W. Newberry

The Virginia copper district is situated in North Carolina and Virginia. It contains many mines and prospects that were active at the turn of the nineteenth century. The Bureau of Mines, as part of the strategic-minerals program, began a project in September 1942 to investigate and explore the most promising of the mines in the district. The Seaboard, High Hill, Durgy, and Blue Wing mines were the sites of the main project activity. This report deals principally with these four mines. Drilling did not discover any new ore shoots but indicated the persistence of known ore shoots in depth. There appears to be no indication of impoverishment of copper with depth.

Jan 1, 1948

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By John W. Frey

This paper is one of a series of digests of foreign mining legislation and court decisions prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of cw Zealand, as prepared by Dr. Frey the best available information in Washington, has been slightly amplified in accordance with suggestions transmitted through the courtesy of the Department of State by W. L. Lowrie, Consul General at Wellington.

Oct 1, 1929

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

[ ]

Jan 1, 2012