Search Documents

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By Frank J. Susko

The U.S. Bureau of Mines has developed a computer model to describe a flotation process. Coal data from conventional flotation has been converted to a simple, two-parameter kinetic model developed by Reuter and van Deventer (1,2)3. Each set of coal data was represented by two constants, a and ß, and an average flotation rate. The success of the model was demonstrated when the calculated and experimental recoveries showed good correlation. The two-parameter model allows complex data to be defined much more efficiently than traditional knowledge-based models.

Jan 1, 2010

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By C. L. Karr

The U.S. Bureau of Mines is currently investigating the use of genetic algorithms (GA's) for solving optimization problems. This computer search technique, based on the mechanics of natural genetics, was used to perform simple least squares curve fitting. Three examples are presented in which a GA manipulates binary coded strings to produce near-optimal solutions to least squares curve-fitting problems after having viewed only a small portion of the search space. The examples include fitting data to the equation of a line, the equation of a parabola, and the Ree-Eyring equation.

Jan 1, 1991

Provide a central source of subsidence reference in formation for industry, academia, and government agencies interested in improving subsidence prediction and analysis under U.S. mining conditions. Approach Develop a comprehensive bibliography about mining related surface subsidence and store this information in a computer file. Make specific references accessible through a key word retrieval program. Supplement these key word identifiers by entry of author's name, title of publication, subject of text, or sponsor of publication. How It Works Requests for subsidence in-formation are made by phone or mail to the Bureau of

Jan 1, 1982

By A. C. Watts, C. A. Allen

In the No. 3 Sunnyside mine of the Utah Fuel Co. a disastrous fire started on the afternoon of August 17 , 1920 , the effects of which are still present in the mine . On account of the extent of the fire , the expense involved in reopening the mine and the opportunities afforded for determining the effects of depleted air , a description of it is worthy of record . This paper is a summary of a more complete report , prepared by the writers , which will be published by the U. S. Bureau of Mines .

Feb 1, 1922

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By M. J. Beus, M. K. Larson, J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of overcoring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 1995

To provide a simple means for rapidly checking methane concentrations at working faces in coal mines while remaining under permanently supported roof. The Approach: A light telescopic probe, through which a gas sample can be pumped Into a methanometer, has been developed. See Figure 1 [ ] How It Works: The telescopic probe consists of sections of small stainless steel tubing encased in sections of lightweight fiberglass tubing. When fully extended the probe is almost 19 ft. long; fully closed it is approximately 5-1/2 feet long. It can be used In either of these positions as well as at intermediate extensions. An approved methanometer is clamped to the probe by a support bracket.

Jan 1, 1975

By Fred N. Kissell

The U.S. Bureau of Mines was established in1910 to reduce .the high accident rate in the nation's coalmines. For 85 years, it conducted a wide variety of tasks related to mining before it was abolished in 1995. The BOM had many technology transfer successes in its lifetime, including more than a dozen "R&D100" awards. This essay identifies and discusses five "transfer factors" that can explain the success (or failure) of many Bureau of Mines projects. These five factors are termed "pressure, pitfalls, path, price, and profit."

By Launa Mallett, Charles Vaught, Kathleen M. Kowalski, Michael J. Brnich

This paper reviews research from the U.S. mining community to define issues relevant to an evolving national and international workforce and to relate them to the emergency response population. The authors further explore and relate the key problem of an aging workforce to the resultant changes and emerging physical and psychological needs of emergency workers. Finally, the authors cite examples from the mine emergency response community and mine rescue experiences to suggest practical recommendations that include both organizational and individual formats, with an emphasis on new approaches to training this changing workforce.

By E. R. Maize, R. D. Currie

"Good ventilation is one of the first requisites in the safe and efficient operation of a coal mine. If a mine is gassy, the uninterrupted circulation of an adequate supply of fresh air is imperative if that mine is to operate with a relative degree of safety. That ventilation is not •only a safety consideration, but is an extremely important economic factor is shown by the fact that in many mines 50 per cent of the total power cost is for ventilation.The system used in the Graceton Coal & Coke Co. mine, Graceton, Pa., is believed to be unusual in many ways. Its application in this mine has re¬sulted in good ventilation of the working faces, no interruption to the venti¬lating current through the use of doors. a large- portion of the air circulated by the fan reaching the working places, low velocity air currents on traveling and haulage ways, low water gage and power consumption of the fan, and well-ventilated gob areas.This investigation was made possible through the courtesy of W. H. Robertson, mine superintendent. Fred Roberts, mining engineer, and Floyd Phillippi, mine foreman, assisted in the collection of information.The Graceton mine is a slope, opening the Upper Freeport or E bed, on the Pennsylvania Railroad about midway between Blairsville and Indiana at Graceton, Indiana County, Pa. The production is approximately 1,000 tons of coal per day and about 170 men are employed underground. The mine is considered gassy and was found to be liberating approximately 300,000 cubic feet of methane in 24 hours. The return airways terminate at a circular, concrete lined shaft 12 feet in diameter and about 115 feet deep at which is the exhaust fan.Mining is done by a block system with flat or level entries turned off the main slope at intervals of 1,350 feet, off which the butt headings are turned up the grade parallel to the slope. Rooms, which are about 225 feet long and 12 feet wide, are turned off the butt headings on 80-foot centers, leaving a block about 68 feet thick between rooms.Haulage on the main slope is by rope, with the hoist on the surface. This hoist is electrically driven through a 500-h.p., 2,300-volt motor. The rope used in this haulage is 1-1/8 inches in diameter. There are five electric trolley locomotives - one 10-ton and four 6-ton - which do all of the hauling in the flat and butt entries.Before it is blasted all of the solid coal and as much of the pillar coal as can be cut with safety is undercut by permissible mining machines. Shooting is done by shot firers who use permissible explosives, electric detonators, and dry-cell, nonpermissible batteries.In rooms where conditions are normal, timbering consists of two rows of posts on 4-foot centers. Posts are required to be within 6 feet of the face in machine-cut places and within 3 feet of the face in hand-mined places. Timbering on entries, where required, is of two types: a bar hitched into the ribs and supported by the coal, or 3-piece sets. The legs of the 3- piece sets used on the slope are set well back into the rib to prevent their being. knocked out by a wreck."

May 1, 1932

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By Sean Gallagher

Study Design. A split-plot experimental design was used to evaluate the influence of posture, trunk angle, and rotational velocity on peak torque output and myoelectric activity during maximal trunk extension maneuvers. Objectives. To determine whether the kneeling posture alters extension torque capabilities in isometric and isokinetic exercises as compared with standing. Also, to ascertain whether recruitment of trunk muscles is modified by such a postural change. Summary of Background Data. Factors such as workplace geometry may force workers to adopt awkward or unusual postures in the performance of manual tasks. An understanding of the limitations placed on strength in unconventional working postures is crucial to the proper design of jobs. Methods. Twenty-one healthy male subjects (mean age = 36 years 7 SD) performed 12 trunk extension exertions in standing and kneeling postures. Isometric tests were performed at 22.5°. 45°, and 67.5° of trunk flexion. isokinetic tests were done at three velocities: 30°/sec, 60°/sec, and 90°/sec. Electromyographic data were collected from eight trunk muscles to assess muscle recruitment under each condition. A prior; orthogonal contrasts were specified for analysis of both torque and electromyographic data. Results. The kneeling posture was associated with a 15% decrease in peak torque output when contrasted with standing; however, no concomitant change in trunk muscle activity was evident. Trunk hyperflexion (isometric tests) and increasing rotational velocity (isokinetic tests) were associated with reduced torque in both postures. Trunk muscle activity was primarily affected by changes in trunk angle and velocity of contraction. Conclusions. A reduced extensor capability exists in the kneeling posture, despite equivalent trunk muscle activity. The similar activation patterns in both postures suggest that the strength deficit does not result from alterations in trunk muscle function. Rather, it may be the consequence of a reduced capability to rotate the pelvis in the kneeling posture, due to a disruption of the biornechanical linkage of the leg structures. [Key words: electromyography, isokinetic, isometric, low back pain, posture. strength1 Spine 1997;22:1864-1872

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924