Search Documents

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By D. E. Ingersoll

This report describes the preparation characteristics of anthracite from the Mammoth and Holmes veins in Schuylkill County, Pa., as determined by the Federal Bureau of Mines laboratory separations at specific gravities of 1.50 to 1.90. The Holmes vein anthracite contains approximately 13 percent ash, and the Mammoth vein contains about 9 percent as fed to the breaker. Crushing Broken, Egg, and Stove sizes from each vein produces Pea-size anthracite of lower ash content than that contained in Buckwheat No.1 size and smaller. The Buck-wheat No.5 size has the highest ash content of all the sizes examined. Potential recovery from a mixture of the two veins as received at the breaker, separated at 1.90 specific gravity, is approximately 64 percent of the feed at 11.0 percent ash. The same materials separated at 1.80 specific gravity yield about 61 percent with an ash content of 10.1 percent. All rejects are from the Holmes vein, because the entire Mammoth material is less than 10.0 percent ash.

Jan 1, 1960

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

By William C. Larson

A study was conducted by the Bureau of Mines to provide quarry operators with information regarding (1) the effects of jointing and bedding on rock fragmentation when bench blasting in two small-scale (2.5-ft) limestone benches, and (2) the successful use of inexpensive equipment and field techniques to determine the orientation and spacing of joints and bedding separations within the quarry. Using inexpensive equipment, such as a pocket transit and steel and paper tapes, joint and bedding separations were mapped and their frequencies measured. Results from two small-scale bench blasts in the Stewartville member of the Galena limestone formation showed that when the row of vertical blast-holes was oblique to the vertical joint orientations, the backface expression was outlined by two relatively large triangular protrusions (joint surfaces). In this blast, part of the rock burden was unbroken. When the line of vertical blastholes paralleled a predominant joint set, all of the rock burden was broken and displaced. The thickness of fragments that had been displaced by a blast correlated with the observed bedding thickness in the bench.

Jan 1, 1974

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By H. R. Babitzke

The purpose of this investigation was to evaluate the potential of columbium-hafnium alloys as structural materials for use at elevated temperatures. The work described in this report was conducted to determine the properties of columbium-hafnium alloys and to select the more promising ones for further improvement. Properties determined in this report were machinability, hardness, workability, tensile strength, and oxidation resistance. Ten ingots, ranging from 100 percent columbium to 70 atomic-percent hafnium, were prepared and subjected to tests. The test results showed that the alloys with 33 and 50 atomic-percent hafnium were superior in workability, strength, and oxidation resistance. For the alloy series tested, the strength and hardness values increased with the increasing hafnium content. Maximum values were reached with 50 atomic-percent hafnium. The oxidation resistance was poorest at the 1 atomic-percent hafnium level but improved with increasing hafnium content through 70 atomic-percent. Eight of the ten ingots were fabricable at room temperature. The two remaining ingots, those with 5 and 10 atomic-percent hafnium, required hot-working.

Jan 1, 1962

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

By C. M. Frost

The hydrodesulfurization characteristics of a Venezuelan topped crude oil and a Venezuelan reduced crude oil were determined at temperatures from 740° to 850° F, pressures from 800 to 1,600 psig, and space velocities from 1.0 to 2.0 Vo/Vc/hr. Kinetic calculations showed that under these conditions the desulfurization reaction was first order with respect to sulfur and had an average activation energy of 32.5 kcal/mo1. Catalyst life tests made at 750° F, with pressures of 800, 1,200, and 1,600 psig and space velocities of 1.0 and 1.25 Vo/Ve/hr, showed that the decrease in the relative activity of the catalyst was a logarithmic function of time or volume of oil processed and the amount of vanadium deposited on the catalyst. Comparative tests made with residual fuels prepared from a Wilmington, Calif., crude oil and a Wyoming asphaltic crude oil showed that catalyst life may be extended by processing fuel oil with a low metal content, but it may be shortened by the presence of large amounts of asphalt in the feed.

Jan 1, 1971

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By H. Robert Ensminger

As a result of the new mining law implemented in August 1985 and the programs conducted by the Institute Ecustoriano de Mineria (INEMIN), which was created by this legislation, there was considerably greater activity in the nonfuels mineral sector during 1986. Over the next 2 years, INEMIN will be developing a national mining plan that will guide Ecuadorean mineral development for the balance of this century. As stage one of INEMIN's mineral study, historical records were reviewed and 300 abandoned mines and 1,200 unexplored mineral deposits were available for further investigation. In 1986, INEMIN established 5 branch offices and negotiated 250 new mining contracts with foreign companies valued at $16 million. Despite all this activity, INEMIN officials estimate that 100,000 square kilometers remain available for claim staking. Technical assistance contracts were signed with Belgium, the Federal Republic of Germany, Italy, Spain, and the United Kingdom, to assist in a variety of assignments ranging from helping prepare the national minion plan to the development of industrial mineral deposits.

Jan 1, 1988

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

By Oliver Bowles

"The American Consul at Guatemala City reports that the Guatemala Marble Mining Company is preparing to operate a marble quarry about 13 miles from the railroad station of Zacapa, which station is a little over 100 miles from Puerto Barrios, the nearest port from which the product may be shipped. The deposit is extensive, and though somewhat broken up in places, great quantities of sound marble are available. It is claimed that the marble is equal in quality to the best product of the Italian Carrara quarries.Access to the quarry by rail is obtained by a spur track of the International Railways of Central America (Ferrocarril Internacional de Centro America) from Marmol, 3 miles south of Zacapa. This spur is about 5 miles long and terminates at the foot of the mountains. A double-track incline cable-way 2000 feet in length has been constructed to bring the marble down the mountain. From the top of the incline to the quarry there is a railway six miles in length over which the rock will be hauled by two side-geared Shay locomotives."

Mar 1, 1920

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 4 Hoist Assemblies (not man-rated) A large number of manufacturers supply materials handling winches. These units are predominately electric powered while a limited number of vendors supply air powered equipment. Air powered units are currently used extensively for underground materials handling purposes. Suppliers of materials handling equipment normally include a disclaimer statement in their published literature which clearly states that the equipment "is not designed or suitable for lifting or lowering persons " This category of commercially available equipment can be adequate for emergency man hoisting provided that its' capacity is suitably derated and provided also that the necessary safety features are incorporated. Section C. 5 details the equipment which could be added to a commercial materials hoist to meet these needs. Four commercially available hoist assemblies, two electric and two pneumatic are discussed in the following paragraphs. This equipment is typical of what is commercially available and three of the units are currently used extensively in mining applications. Each hoist description includes a remarks paragraph which identifies the additional equipment each hoist would require for emergency hoist use.

Jan 1, 1976

By E. C. Lane

"INTRODUCTION This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36 3/. The second resort gave the same data for motor gasolines sold during the summer of 1936 4/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-37 5/.This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others."

Dec 1, 1937

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By E. R. Bauer

The U.S. Bureau of Mines is investigating strata interactions associated with mining of multiple coal beds to provide the mining industry with improved methods of planning and developing multiple coalbeds, conserving resources, and increasing the safety of underground coal mining. This study involves analytical predictions and underground observations of longwall development ground control problems at a south-central Pennsylvania coal mine affected by subsidence induced by multiple-seam mining. As predicted, strata interactions were found in upper mine areas mined over lower mine gob. Observations revealed roof deterioration accompanied by excessive water inflows in the first 170 ft after crossing the gob line as mining entered and exited the subsided area (over the lower mine gob). In contrast, superimposed mine areas and areas mined a substantial distance out over the gob showed no signs of interaction with previous lower seam mining, again as predicted.

Jan 1, 2010