Search Documents

By John J. Mulligan

Ear Mountain is an isolated mountain mass that rises abruptly from the coastal plain on the northwest shore of the Seward Peninsula. Geologically it resembles the more accessible Brooks Mountain and Cape Mountain areas to the southwest, being composed of a granitic core surrounded and partly capped by metamorphosed sediments. The occurrence of lode- and placer-tin deposits in this area has been known since the early 1900's, when the Seward Peninsula region was prospected extensively for both gold and tin. The Federal Bureau of Mines investigated the tin deposits in the Ear Mountain area during the 1953 and 1954 field seasons. The objectives were to delimit the areas in which tin minerals occur, as a guide to future prospecting, and to determine the amount of tin in the known prospects. Work by the Bureau of Mines included both placer and lode sampling.

Jan 1, 1959

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By Donald O. Capstick

In 1481, U.S. Bureau of Mines personnel conducted a survey of mines, prospects, and mineral resources in the Table Mountain RARE II area. There are no mines or active prospects in the study area. One prospect in the study area, the Waterfall Prospect, is estimated to contain 480 tons (440 t) of indicated subeconomic tungsten resources averaging about 0.18 percent tungsten trioxide (W03). Other tungsten occurrences are at the Stevens Prospect, just northwest of the area. Stone and sand and gravel deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 4,400-acre Table Mountain study area is 13 mi (21 km) southwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir wilderness adjoins the study area on the southwest (fig. 1).

Jan 1, 1982

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By Margaret R. Egan

The U.S. Bureau of Mines investigated the product-of-combustion (POC) characteristics of combustible materials used in typical coal mining operations in a series of experiments conducted in an intermediate-scale fire tunnel. The materials examined include wood cribs, transformer fluid, coal, conveyor belting, brattice cloth, and ventilation ducting. Smoke and toxic gases evolved from burning materials contribute to panic conditions and hinder escape. Smoke irritates and obscures vision, while toxic gases physically debilitate and disorient the victims. However, POC emissions may be used for early warning fire detection. POC levels will vary not only between materials but also between stages of combustion and the conditions in which they are burning. This report summarizes the POC characteristics of each material and evaluates their effectiveness for early warning mine fire detection. Results show that smoke was the POC most readily detected from the smoldering materials tested.

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

This chapter defines light as a type of energy, and tells how different features of light are measured. It 1s important to understand the units of light measurement because they are used throughout the rest of the book. But more Important, this will help you to understand the "regs" and how to get the best out of the lighting you have available! By the time you complete this chapter, you should know what candle-power, foot-candle, and foot-lambert refer to, and you will also be able to tell why the helmet that the new miner wears appears orange to human eyes. Light that you "see" is really radiant energy that hits the retina of the eye. Radiant energy moves out from a light source much like a series of bullets from a number of machine guns being fired at the same time in all directions.

Jan 1, 1976

? A roof bolter reaches for a lever while guiding the drill with his other hand. Since he's watching the drill and many of the controls look and feel alike, he hits the wrong control and crushes his hand. ? Six hours into the night shift, an ore truck driver dozes off. The truck plows over the berm and down into the pit. ? Fleeing a afire, a face crew sees smoke in the intake entry. Assuming the fire is ahead, they cross over to another entry, but soon encounter even worse smoke. These very different accidents have at least one factor in common: the human factor. The actions, decisions, thoughts, or perceptions of one or more humans contributed to the accident. These are just a few examples of safety problems researched by the Human Factors Group of the Pittsburgh Research Center, U.S. Department of Energy.

Jan 1, 1998

By Miklos D. G. Salamon, Jim M. Galvin, Bruce K. Hebblewhite

A series of mine design accidents in the late 1980s resulted in a major research program at the University of New South Wales, Australia, aimed at developing pillar and mine design guidelines. A database of both failed and unfailed Australian underground coal mine pillar case studies was compiled. A procedure was developed to enable the effective width of rectangular pillars to be taken into account. The database was analyzed statistically using the maximum likelihood method, both independently and as a combined data set with the more extensive South African database. Probabilities of failure were correlated to factors of safety. It was found that there was less than a 4% variance in pillar design extraction ratios resulting from each of these approaches. There is a remarkable consistency between the design formulas developed from back-analysis of the two separate national pillar databases containing many different coal seams and geological environments.

Jan 5, 1999

By E. R. McMillan, M. R. Geer, Joseph Daniels, H. F. Yancey

Investigations of coking properties of Washington coals made before 1939 and studies of coking precesses indicated that PiaTceC:Countyx:oals, particularly those from the Vlilkeson-Carbonado--Fairfax area, yield excellent coke structures. ThE: ash content of the cokes W2S relatively high, sulfur ordinarily.was low, and the phosphorus, although variable, was not excessively high for some purposes. For years the coals had been coked in beehive and standard byproducts ovens and had entered Pacific coast markets for every purpose to which coke is adapted. Certain areas of the Roslyn bed of Kittitas County also were known to possess coals with coking properties. This coal had been employed largely for bench-gas manufacture and occasionally, blended with other coals, in byproduct ovens. Coals from other western Washington areas also had baen utilized for coking in the past but were not of immediate significance.

Aug 1, 1943

By Margaret R. Egan

In an underground mine fire, a toxic mixture of combustion product gases and particulate matter is transported by the ventilating system endangering everyone downstream. To determine the magnitude of the problem that these toxic combustion products pose, the U.S. Bureau of Mines is investigating the combustion products of typical materials found in underground mines. The total toxicity of the combustion products depends upon the evolving gas species and particulate matter, the amount of material involved, and the ventilation rate. In a simulated mine environment, the products from smoldering poly- vinyl chloride (PVC) brattice and conveyor belting were analyzed for gas concentrations and smoke characteristics. The primary toxic gases are hydrogen chloride (HC1) and carbon monoxide (CO). Smoldering conveyor belts are more detectable than smoldering PVC brattice cloths. These results, combined with previous analyses, are used to estimate relative toxicities, product levels, and detect-ability of smoldering mine combustibles.

Jan 1, 1992

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

By BUREAU OF MINES

The approval of the U. S. Bureau of Mines when granted to a manufacturer for a gas mask is a certification that the particular device has been submitted to the Bureau of Mines for inspection and test and has been found to meet that bureau's published minimum requirements for safety , durability , and satisfactory performance . Any de- Gas masks are approved by the Bureau of Mines only as a complete unit or assembly of parts , as canister , facepiece and harness . This is in order that responsibility for rigid adherence to the bureau's requirements may be definitely located and not divided . vice marketed under this approval must be a unit composed of parts identical in detail of design , assembly , workmanship , and quality , and produced under the same control and inspection as the original device to which approval has been granted . The particular parts which comprise the approved assembly are designated in a letter to the manufacturer at the time the approval is granted . In recent years they are also specified in the approval plate authorized for use in connection with the sale of the device . Each part permitted in the assembly is legibly marked by name or number for the guidance of users of masks in ordering and identifying approved parts when making repairs , and thereby maintaining their equipment as an approved device . In view of the foregoing , any change in the design of parts or deviation from the permitted assembly of parts would violate the conditions under which approval was granted and the device would not be considered as meeting the approval requirements of the Bureau of Mines . The U. S. Bureau of Mines has been frequently requested to interpret the approval status of a gas mask assembled from parts which have separately met its requirements as components of two or more approved devices but which in the form of a complete unit has not been submitted for tests or been granted approval . Responsibility for the elements and for their proper assembly is in such case divided . Such assembled units have no status as permissible equipment under the Bureau of Mines system of schedules . The reasons underlying this policy are that the approval is granted only to some one who assumes responsibility for the whole and that the details of assembly and coordination of parts are considered to be important to the satisfactory performance and safety of the device .

Sep 1, 1932

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By J. L. Ambs

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground, mines, to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such 'as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

Jan 1, 2010

By E. D. Gardner

About five minutes after 3 o'clock on Thanksgiving morning, November 24, 1927, smoke was discovered coming up No. 2 shaft of the Magma Copper Co.'s mine at Superior, Pinal County, Arizona. Of the 49 men in the mine at the time, 42 were able to make their way to the outside unassisted, but 7 perished. Six bodies were recovered, and the seventh, that of an Apache Indian cage-tender at No. 2 shaft, is thought to be in the caved section between the 1,600 and 2,250 foot levels A second and independent fire broke, out in No. 1 shift about 2 a.m., November 27, burning .out the shaft timbers from the surface to the 200-foot level and destroying the surface fan and structures. About 20 men were underground fighting the fire in No. 2 shaft, but all were safely withdrawn, aril the fire in No. 1 haft was quickly controlled.

Jan 1, 1928

By Bryan F. Ulrich

If resin-grouted roof bolts are not installed correctly, mine roof reinforcement can be affected, and roof falls can result. A bolt installation variable that is readily controlled by the mine operator is annulus thickness. The objective of this U. S. Bureau of Mines investigation was to study the effect of annulus thickness variations on the integrity of 3/4-in-diam resin-grouted bolts. Forged-head test bolts, 2 and 1 ft long, were installed in concrete blocks that had been drilled with 1-, 1-1/8-, 1-1/4-, 1-3/8-, and 1-1/2-in-diam bits. Standard pull tests were performed; then the concrete was broken away from the bolts so that grout mix quality could be inspected. It was found that the optimum annulus thickness is 1/8-in (l-in-diam drill hole), and as annulus thickness increases from the optimum, there is a corresponding decrease in grout mix quality, effective grout ratio, and axial stiffness.

Jan 1, 1989