Search Documents

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By L. A. Neumeier

Sound experimental ingots of zinc alloys for use as rolling slabs were cast with a specially constructed, semicontinuous casting machine. Nominal alloy compositions of Zn-1.0 percent Cu, Zn-0.12 and 0.36 percent Ti, and Zn-1.0 percent Cu-0.03 to 0.36 percent Ti were cast. This Bureau of Mines study was conducted to evaluate the suitability of the casting procedure for providing stock for rolling into sheet. Microscopic examination of ingot sections revealed structures in which grain size varied from the outer to center ingot zones. Columnar grains present in the center zone of the Zn-1.0 percent Cu ingot were absent in the titanium-containing ingots. The ingots with titanium displayed a finer grain size and eutectic structure in the center ingot zone than in the outer zone; the transition in grain size between the two zones was quite abrupt in some ingots. The overall grain size of the titanium-containing ingots was finer than that of alloys cast by more conventional methods. Chemical analysis revealed that compositional segregation is not a significant factor in the formation of the ingot structure. Microstructural studies of small ingots of similar alloys solidified at slow, fast, and intermediate rates confirmed that the ingot structure in the semicontinuous-cast ingots is related to cooling rate, which is, in turn, related to the particular casting machine design and the influx of cooling water on the withdrawing ingots. Microstructures of thin sheet hot-rolled from slabs of the semicontinuous-cast ingots demonstrated that the ingot structure does not preclude the rolling of sheet having a uniform microstructure. Results of hardness surveys of the semicontinuous-cast ingots demonstrated that copper and titanium exert essentially additive hardening effects in these cast alloys.

Jan 1, 1968

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure., but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo,, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of intolerability which -accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a nonodorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By P. G. Barnard

The Nation's steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

By H. Kenneth Sacks

The Bureau of Mines has developed hardware for electromagnetic (EM) detection and location of miners trapped in underground coal mines. This report describes a technique for using the developed equipment for locating uncased boreholes underground. Results of several field and laboratory experiments are described.

Jan 1, 1978

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Michael R. Grubbs

The Bureau of Mines is currently developing methods for reclaiming the metal and mineral values contained in unburned urban refuse. One important phase of this research deals with recovering Mastic from shredded refuse using in electrodynamic separation process. The results of this study have indicated that mixed plastic concentrates analyzing 99.4 percent plastic can be consistently recovered from the light material fraction of shredded refuse, leaving a mixed paper traction analyzing 99.9 percent paper. Recovery of the plastic exceeds 99 percent.

Jan 1, 1972

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By Raymond P. Maloney

The Rhyolite mercury prospect is on the south flank of Juninggulra Mountain--a large rhyolite intrusive in the Kuskokwim River region about 36 airline miles northwest of Red Devil, Alaska. Bulldozer trenching by the Bureau of Mines exposed bedrock at intervals in a 2,000-by 3,000-foot area where previous prospecting by the owners had disclosed abundant float and several in-place stringers containing cinnabar in widely varying amounts. The additional trenching indicated that the mercury mineralization in the limited area investigated was confined to erratically distributed short stringers and to small lenses, occurring in discontinuous zones in numerous silica-carbonate dikes and sills or along their altered contacts with sedimentary rocks. The geologic relationship of the mercury-bearing silica-carbonate dikes and the nearby rhyolite intrusive is similar to that existing at several other mercury mines and prospects in the. Kuskokwim region. The depth of over-burden and the presence of permafrost were serious obstacles to bulldozer trenching, and only a comparatively small part of the mineralized area was thus investigated.

Jan 1, 1962

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to 'precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961