Search Documents

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By Earl C. Lane

This is the second of a series of reports on a survey of petroleum products manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in other parts of the United States, and the claim has been made that some of the present federal Specifications for petroleum products tend to discriminate against California products. The purposes of the present survey are to determine what particular specification requirements California petroleum products characteristically fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what 'lines investigation to determine the question should proceed. The first report* of the series gave the physical and chemical properties of gasoline and mineral spirits made from California crudes. The present report deals with lubricating oils. Sixty-one samples of lubricating stocks and finished commercial products were generously donated by four of the large refining companies of California. Fifteen samples of automobile lubricating oils, made in California from California crudes, were purchased in the open market. Nine samples of lubricating oils mode from Gulf Coast crude were contributed for comparison by a company in Texas. The refining companies have continued the helpful and cordial cooperation shown by them in connection with the earlier work of the survey.

Jan 1, 1923

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By C. N. Schuette

"The production of silica and magnesia crucibles in the induction furnace was attempted and achieved in the laboratory of the Pacific Experiment Station of the United States Bureau of Mines. This work was undertaken at the request of other stations for laboratory crucibles of a certain specified wall thickness and capacity.The essential new parts of this work are the development of a technique for the high-frequency furnace production of silica crucibles of greater wall thickness than could be readily fabricated from commercial fused silica, and for heavy-walled magnesia. crucibles of great density and mechanical strength. A considerable bode of patent literature on the Production of fused silica ware in resistor-type furnaces was examined, but it furnished no significant help for the present problem. Similarly sintered magnesia refractories are often made for technical purposes, but for use at temperatures of 2000o C. or over, the material must be sintered at higher temperatures than can be attained by combustion firing, and the very great shrinkage encountered at these temperatures requires special methods. Small crucibles. of magnesia fused in the electric arc have been made by Tritton and Hansen,3 but the practical size of such containers is very limited.Many different methods of making crucibles in the induction furnace were tried before satisfactory results were obtained. The following description covers only the most satisfactory method, which produced crucibles of excellent quality in a reasonable time and with a moderate expenditure of power and materials."

Oct 1, 1929

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

By Connie S. Musulin

Radon concentrations in shallow uranium mines such as the Bureau of Mines experimental research mine are affected by barometric pressure changes. The radon concentrations show a significant correlation with absolute pressure; but over a period of days, a steady rise or fall in barometric pressure will result in noncorrelation of data. Fan shutdowns also affect radon concentrations, and an equation was derived to determine the time required for the radon concentration to return to normal after a fan shutdown, whether the ventilation is blowing or exhausting.

Jan 1, 1982

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

Reduce spillage hazards and contamination when adding hydraulic nil to mining machine reservoirs. Approach An easily transported module, that delivers hydraulic oil directly into mining machines, was built and tested. How It Works The Hydraulic Oil Delivery Module is carried, from the oil storage area to the equipment needing oil, in the bucket of a scoop or other utility vehicle. Oil is pumped into the module reservoir from storage, or out of the module reservoir into the machine being serviced, through a long hydraulic hose. During long-term testing, the 115 foot long delivery hose made it possible to replenish the hydraulic oil in mining machines at the face with only limited interruption to the mining operation. (Figure 1 shows one! version of the module.) The compact Hydraulic, Oil Delivery Module consists of: an oil reservoir: a pump driven by a hydraulic motor; two high pressure, low volume oil lines, filters; and a low pressure, larger capacity delivery hose equipped with quick-connect-couplers. The high pressure oil lines are connected to the scoop's hydraulic power takeoff, which supplies the power to pump oil in or out of the module reservoir.

Jan 1, 1977

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By Fred N. Kissell

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By R. D. Currie

Many coal companies have a system for checking men into and out of the mine , and generally such systems appear to be perfectly sound and adequate . However , when the real test comes at the time of a mine disaster , too often the system is found to have failed , and hours and sometimes days pass before it is known how many men are in the mine and who they are . Most of the systems in use , when properly maintained , are adequate for the routine work of the mine , and some of them may prove adequate at the time of a mine disaster . All systems , however , depend upon proper supervision and strict adherence to the system .

Jun 1, 1930