Search Documents

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

Significantly reduce respirable dust exposures of longwall shearer operators when cutting out at the headgate. Approach As a result of Bureau research, a ventilation curtain is recommended to be mounted between the stage loader and the coal rib to more effectively prevent the ventilation air from blowing across the shearer drum as it cuts out at the headgate. Some mine operators already employ this method of reducing dust, but a vast majority do not. How It Works One source of extreme concentrations of respirable dust for longwall shearer operators is the shearer headgate drum as it cuts through into the headgate entry. As the drum cuts into the entry, it is exposed to the primary ventilation airstream. The high velocity air passes through and over the rotating drum, picking up large quantities of dust.

Jan 1, 1982

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By J. M. Stuve

The standard heats of formation (?Hf°) of holmium trichloride and terbium trichloride were measured by solution calorimetry. Heats of solution of holmium and terbium metals and their anhydrous chlorides were measured in 4.360 molal HCI at 298.15° K. From these measurements ?Hf° for HoC13 (c) was calculated as -240,290 ±1,700 cal/mo1e, and ?Hf° for TbC13 (c) was calculated as -238,330 ±1,500 cal/mole at 298.15° K.

Jan 1, 1967

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

Produce an annotated bibliography to serve as a comprehensive source of published information available on the use of soil amendments in coal mine reclamation and the characterization of coal mine soils. The Problem There is a substantial amount of information available tin coal mine reclamation and revegetation, particularly on the use of soil amendments to ameliorate site conditions and aid vegetation establishment, growth development, and productivity. Additionally, site characterizations based on chemical, physical, and mineralogical properties have been thoroughly researched. This information, however, is widely disseminated throughout various professional and scientific journals, State and Federal documents, proceedings of conferences, theses, and other technical writings. A critical need exists for a comprehensive and up-to-date summary of published information concerning the uses, methodologies, and types of soil amendments that arc necessary for reclamation success.

Jan 1, 1991

By J. E. Pahlman

The Bureau of Mines conducted re-search to determine the resistance of basic refractories to corrosion by ash slags that would result from the burning of coal and lignite in metallurgical operations. Basic refractories are of economic interest because they are from one-third to one-half as expensive as 90-to 99-pct-alumina refractories. Static tests were performed at 1,300° C and dynamic tests at 1,400° to 1,650° C to investigate the stability of refractory specimens in a slag environment. In alkali-containing lignite ash slags, in order of decreasing resistance, magnesite, magnesite-chrome, and chrome-magnesite refractories all had corrosion resistances equal to or better than 90-to 99-pct-alumina refractories. These basic refractories formed slag penetration layers in dynamic tests, which helped protect them from further attack. Chemically bonded basic refractories in general did not have as good a resistance to slag attack as did burned refractories of the same composition. In very acidic coal ash slag, a chrome-magnesite refractory containing 30 pct MgO plus a slag inhibitor and direct-bonded magnesite-chrome refractories with 60 pct MgO had good resistance to attack. Chrome-magnesite refractories (30 to 40 pct MgO) were moderately to severely attacked, and refractories with greater than 70 pct MgO were severely attacked by this same slag.

Jan 1, 1982

Provide a strategy for calculating optimum distribution of selected sensors for detecting underground mine fires. Approach The Bureau of Mines performed research to determine adequate distribution of product-of-combustion (POC) fire sensors within mine entries. This placement strategy would improve the miner's chances for escape by locating sensors where they would most effectively, quickly, and efficiently detect fires resulting from coal or wood combustion. Spacing of Sensors Placement strategy guidelines were based on the performance of 160 F heat sensors with ideal operating characteristics which were placed at intervals of ten feet in underground mine entries. Data obtained from full-scale mine fires were used to estimate fire sizes and alarm activation times for the heat sensors. Various equations were then developed to determine spacing requirements for any fire detection system installed in entries of varying heights, widths, and ventilation rates.

Jan 1, 1983

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

Mine closing methods should be carefully considered. If not properly sealed, an abandoned mine may continue to produce acid water. Since 60 to 90 percent of the total acid discharged from all coal mines is from abandoned mines,(58) some states require that provisions for sealing be contained in the mining permit application. Closing an operation to prevent harmful mine drainage into nearby runs and streams is a subject of much concern to states as a result of continuing problems from long abandoned mines which were improperly closed.

Jan 1, 1970

By John C. LaScola

The Bureau of Mines repeatedly surveyed a grid of monuments over an active longwall mine panel in southwestern Pennsylvania during a 1-year period. Both conventional ground surveying techniques and photogrammetry were used. The objective of this investigation was to compare elevation measurements of subsidence obtained from aerial and ground survey methods under dynamic ground conditions. The results of a statistical analysis of the survey data show that the mean of the differences between 372 matched pairs of elevation measurements was 0.20 ft (61 mm) with a 95-pct-confidence interval of 0.05 ft (15 mm). The mean of the absolute values of the differences was 0.38 ft (116 mm) with a 95-pct-con-fidence interval of 0.04 ft (12 mm). Ninety-five percent of the absolute values of the differences were less than 1.11 ft (338 mm).

Jan 1, 1988