Search Documents

By Robert F. Chaiken

A quasi-steady-burning channel model is used in this Bureau of Mines study to describe the conductive heat loss from an in situ coal combustor to the surrounding rock strata. The calculated heat losses are significantly greater than those previously estimated, but are still very acceptable from the viewpoint of energy recovery. Approximately 80% to 90% of the heat of combustion of the coal should appear as sensible heat of the gaseous exhaust, with exhaust temperatures in the range of 1,000° to 1,200° C. The effects of burning stoichiometry and channel size on the heat loss are also discussed in terms of the model. Such effects are shown to be compatible with an in situ combustion process even in thin seams. However, these results depend on gas leakage and adverse roof falls not being important factors in deter-mining the heat loss mechanism.

Jan 1, 1977

By Nicholas T. Zilka

One mineral deposit in the Golden Trout Wilderness has potential. The currently producing Pine Tree Mine on the Little Kern River has an estimated 120,000 tons (109,000 t) each of indicated and inferred reserves averaging 0.77 percent tungsten trioxide. No apparent potential exists for base or precious metal or other mineral deposits. INTRODUCTION The Golden Trout Wilderness, established by Congress in 1978 under Public Law 95-237, encompasses 240,000 acres (97,000 ha) of conifer-forested, rolling, upland plateau at the headwaters of the Kern River in Inyo and Sequoia National Forests (fig. 1). Abundant streams locally contain Golden Trout, namesake of the area. Major roads serve the area to the west and east of the Wilderness; access is poor to the north and south.

Jan 1, 1982

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By Scott Turner

The settlers of a new country necessarily suffer at first from the lack of accumulated stocks of metals - in-use that are possessed in older countries . Our American colonists were at first compelled to import their metals in manufactured forms , and it must have proved difficult to produce an exportable surplus of commodities with which to pay for them . These circumstances stimulated a search for domestic ore deposits . Various discoveries resulted , so that as early as 1628 , we find the colonists importing two craftsmen from England to establish iron -works in Massachusetts to beneficiate local ores . In 1648 , an iron -works at Lynn was producing metal at an annual rate of 400 tons . Later on , the colonial iron industries became of importance , some metal being actually exported to England . The people of this country thus early became convinced of the necessity for domestic mineral production . It is now little realized how persistent were their efforts to - make mineral discoveries , before the gold- rush to California ; the extraordinary success of our subsequent mineral explorations has overshadowed the earlier record . Precise and complete accounting of our mineral production , having the character of national bookkeeping , is available only for the series of years beginning with 1880 , when commences the official record that is provided by the Government publication called Mineral Resources of the United States . In the period of 52 years , from 1880 through 1932 , the value of mineral production of the United States amounted to more than 122 billion dollars . Only 12 billions of this total were produced in the 21 years , 1880-1900 , while nearly 110 billions were produced in the first 31 years of the present century . Of this 110 billions , over 53 billions were produced in the most recent decade , 1921- 1930 , the production of the previous decade , 1911-1920 , having been only 37 billions , though it included the war period ; that of the decade 1901-1910 was 16 billions . In 1931 , the total value of mineral products of the United States was $ 3,180,000,000 , compared with an average annual value of $ 5,556,000,000 during the previous five - year period , 1926-1930 . The decline in 1931 from that average was therefore 43 per cent . As to the three great groups of mineral commodities , metals fared worst , with a decline of 55 per cent in the value of their production , while the value of fuels declined 39 per cent , as did that of the nonmetals group .

Jan 1, 1933

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

By M. MacLaughlin, J. Whyatt

A case study is presented that relates statistical descriptions of joint sets to the distribution of local wedge failures along the crest of a catch bench at the Yellowstone Talc Mine. The fracture sets and bench width were mapped by teams of geological engineering students from Montana Tech under the direction of Dr. Mary MacLaughlin. The students analyzed the fracture data, conducted physical property tests, and used a beta version of a NIOSH program “Bwedge” to predict the distribution of surviving bench widths. In the course of this analysis the students developed evidence of software performance issues that, unfortunately, frustrated their analysis. These have now been addressed and a full analysis completed. The analysis confirms the validity of the student mapping program and provides insight into the effects of blasting and excavation practices on the bench. It also provides a tool for exploring the pattern of bench crest failure that would result from variations in both bench geometry and blasting practices.

By L. W. Brandt

As part of its objective to expand the body of mineral information as a basis for new technology, the Bureau of Mines conducted research on the fundamental behavior exhibited by phosphate clay waste in settling ponds. A semiempirical equation used to describe the compaction of ceramic powders in a single-acting die was applied to aqueous phosphatic clay waste and attapulgite slurries. This equation, [*V = a1 e ?k1/P + a2e ? k2/P] was found to describe the compaction of an attapulgite gel and a phosphate slime gel by a moving screen. [*V] is the ratio of the compaction achieved at a given pressure, P, to the compaction achieved at a pres-sure sufficient to remove all space between particles. The constant al represents the fraction of compaction achieved at low pressure by rearrangement of floes to higher packing density, and a2 represents the fraction of compaction achieved at higher pressure resulting from removal of voids within floes. K1 and K2 are constants determined from the experimental data. Both the low-pressure and high-pressure compaction mechanisms were observed in the compaction of the clays. These two compaction mechanisms offer an explanation for the observation that impounded slimes initially dewater rapidly and then dewater at a much slower rate.

Jan 1, 1982

By R. D. Currie

"A million tons of coal mined in the Pennsylvania anthracite region without a fatality is a feat of which to be proud and one that deserves the commendation of the entire mining industry. The average production per fatality in this region for 1933 was 206,823 tons, an exceptional record showing the results of an intensive drive made by the Pennsylvania Department of Mines and the anthracite operators and-workers to curtail the high accident rates heretofore prevailing in the region.This paper gives information about a mine with a record five times better than the average which should prove to the industry that mine accidents can be reduced through the proper safety organization and effort. The Pine Hill Coal Co., managed by Weston Dodson & Co., Inc., and located at Minersville, Schuylkill County, Pa., has made such a record at its Oak all colliery by studying its accident experience, realizing the facts, and pursuing a definite safety policy with a view to bettering its accident occurrence.As a direct result of its safety policy this colliery has produced 1,044,000 tons of anthracite without a fatality; within 3 years it has reduced its total accidents from 645 to 105 per year, its compensable accidents from 204 to 45 per year, and its lost-time accidents from 335- to 67 per year. In addition, it has set up a smoothly functioning safety organization that will go fax in aiding in the continuance of this great work of mining anthracite at a lower .cost in human suffering.This circular describes the accident-prevention methods perfected and the results obtained by this colliery in the belief that similar methods will produce essentially similar results at any other colliery where they may be adopted.The writer acknowledges his indebtedness to the officials of the company who furnished him with the details of the safety organization and the data from which this report was prepared. He especially desires to thank Messrs. Stockett, general manager, Wells, general superintendent, Morgan, safety engineer, and Kistler,- statistical department, for their hind assistance.The mine is opened by shafts, slopes, and drifts, a characteristic of minas in the Southern anthracite field. Thirteen different beds of coal are being mined. The thickness of the beds ranges from 3.5 to 16 feet and the pitch from 0 to 900. The roof and floor exhibit the entire range of conditions found in anthracite mines. Table 1 describes the coal seams being worked."

Aug 1, 1934

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

By G. W. Murrie, W. P. Diamond, C. M. McCulloch

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over- burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By Staff

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground 'bed resistance monitor.

Jan 1, 1979

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

Tables

Jan 1, 1992

By D. Harrington, B. W. Dyer

"One of the products of the activities of the United States Chemical Warfare Service is a simple device and method for nearly instantaneous determination of small quantities of carbon monoxide in air. Since the war, this device has been diverted to commercial uses, and is now being marketed in connection with rapid determination of the comparatively small but dangerous quantities of CO, which may be found in garages, in sewers, about blast furnaces, etc. Also, it probably has a definite field of use in both coal and metal mines in connection with fires and explosions, as well as in confined places after firing of explosives) the latter applica-tion being of especial importance in metal mining.The device as marketed is readily portable, being small and light enough to carry in a coat pocket of medium size. In operation, a sample of the air mixture is drawn into a small rubber bulb, then forced through a small glass tube filled with certain chemicals upon which CO has the effect of changing the original color from gray or white to shades of green, the deepness of the green determining the percentage of CO in the air. A color scale is attached for purpose of comparison and determination of CO percentage. Only a few minutes are consumed in obtaining the result, all work being done on the ground.The exact effect of minute quantities (up to 1/10 of 1 percent) of CO on the human system is somewhat uncertain, and much research has been and is being done to obtain definite data on this point. It is, however, definitely known that in air containing more than 1/10 of 1 percent CO men doing hard work are quickly and seriously affected. As the gas is tasteless, colorless and odorless, methods of determining the presence of both small and large quantities have been of much importance. Technical Paper 11 of the U. S. Bureau of Mines gives much data as to effect of CO on mice and canaries. It was found that mice show very little distress until the CO content is about 0.20 percent, but quickly succumb when that percentage is exceeded; canaries are somewhat more susceptible; they quickly show distress in as little as 0.15 percent 00, and soon collapse when that percentage is exceeded."

Jan 1, 1921

By Launa G. Mallett, Barbara Fotta

This report examines the effects of mining height on injury rates in U.S. underground nonlongwall bituminous coal mines, controlling for both the employment size of the mine and the mining methods. Using the mine-level employment and injury data reported to the Mine Safely and Health Administration, mines were stratified by average coal seam height (<43 in, 43-60 in, and >60 in) and by the average number of employees working at the mine (<20 employees, 20-49 employees, 50-99 employees, and >99 employees). To reduce the confounding effects of mining method on injury rates, mines using longwall mining methods were identified and excluded from analysis. The employment data show that as the mine size increases, the proportion of hours worked in low seams decreases substantially. Additionally, miners injured in small, low- scam mines arc, on average, younger and less experienced than those injured in large high-seam mines. Nonfatal disabling and fatal injury rates were computed within each category of employment size and seam height for the major types of accidents (ground falls, powered haulage equipment, machinery, handling materials, slips and falls, and hand tools). Our findings suggest that, regardless of the employment size, as mining height increases, miners are at increasingly higher risk of injury from accidents due to slips or falls and accidents involving shuttle cars and falls of ground. As mining height decreases, miners are at higher risk 01 injury from accidents involving roof bolting machines, load-haul-dump types of powered haulage equipment, personnel carriers, and powered haulage conveyors. On the other hand, regardless of the height of the coal seam, miners working in large underground mines had higher rates of injuries resulting from accidents involving handling materials and nonpowered hand tools, but lower rates of injury from accidents involving continuous mining machines and lower rates of fatal injuries from falls of supported and unsupported mine roof. Finally, miners working at small mines in low or medium seams are at higher risk of being fatally injured by a ljll of unsupported mine roof. These findings suggest the importance of&apos; considering the working height of the mine, as well as the employment size of the mining operation, when developing intervention strategies to reduce injury risk to underground coal miners. Results also identify the need to further explore how mining height contributes to the frequency and severity of injuries.

Jan 11, 1997