Search Documents

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

By D. D. Bolstad

The Bureau of Mines has developed procedures for sampling the geometry of fractures in underground coal mines. Stratified cluster sampling and the unit area concept are applied to the collection of fracture orientation data. The use of unit area mapping, stratification, and site delineation is made to assure collection of representative data. The procedures developed here help to isolate sources of variability in the fracture patterns.

Jan 1, 1973

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989

By R. O. Pynnonen

Tunnel-driving is recognized as a hazardous occupation; adequate support of roof and sides for preventing accidents from falling material is usually one of the most important safety problems. Where extraordinary conditions of sand and water are found, this problem becomes even more difficult. Tunneling at the Tioga No.2 mine was stopped when a 22-foot bed of water-saturated, fine gray sand was encountered. The tunnel, designed to house an ore-conveyor belt, was being driven from both ends. Driving was extremely difficult at both the upper and lower faces when the sand horizon was reached. A distance of 178 feet remained between the faces. Heavy pressures deformed the steel-supporting rings at the upper face, and there was an inrush of mud and sand at the lower face.

Jan 1, 1958

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By W. D. Ryan

The American public has at all times been prone to discuss important questions that call for consideration and adjustment. Debatable subjects upon which sides may be taken always receive unusual prominence, but other questions equally important may be neglected. The real "paramount issue," calling for remedial action, is the ever-increasing number of deaths caused by preventable accidents. This matter demands the attention of the entire American people; the importance of accident prevention can not be overemphasized, and in many phases of American life, especially among the mining and allied industries, far too little real attention has been given the importance of conserving life and limb by accident prevention. ACCIDENTS COMPARED TO WAR AS A CAUSE OF DEATH Harry T. Hoffman, Wyoming labor commissioner, writes the following: It is one of the peculiar complexes of this rapidly moving age that we all stand aghast at the horrors of war and view with appar- ent indifference the greater havoc of industrial peace. Did you ever stop to think that approximately twice as many people were killed by accidents in the United States in 1929, as there were American soldiers killed in the entire period of the World War? Every employer and every worker should be thoroughly aroused over the tremendous toll levied against industrial forces by accidents which are largely preventable and develop a faith in safety efforts that will fire them with a zeal as pronounced as that of their religion or their patriotism. Let us remember safety-first to the end that the workman shall live to enjoy the fruits of his labor; that his mother shall have the comfort of his arm in her age; that his wife shall not be untimely a widow; that his children shall have a father; that crip- ples and helpless wrecks who were strong men shall no longer be a by-product of industry.

Apr 1, 1931

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

Reduce the dust levels to which jacksetters and helpers on auger mining sections are exposed by identifying viable, effective methods for control-ling respirable dust on these sections. Approach The Bureau of Mines con-ducted laboratory tests and respirable dust surveys to identify the factors that distinguish clean auger mining operations from dusty ones. Study Results Results of the Bureau's study revealed that ventilation is the most important element of auger mining dust control. The four must important venitilation parameters are airflow, curtain configuration, curtain setback, and curtain installation.

Jan 1, 1988

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By R. Hogg

"Some basic features of the science and technology of particle systems are reviewed in the context of agglomeration processes. Emphasis is placed on the force of interaction among particles and with their environment and on their dependence on particle characteristics and interfacial phenomena. The complex role these forces play in the various stages of agglomerate formation, growth, consolidation and structure development, and their influence on final product properties is discussed.INTRODUCTION Agglomeration is an example of a process where the technology has generally preceded the science. Process development• has very often been by trial-and-error albeit with an eye on some basic principles. Nevertheless there is' a scientific basis to the process and a better understanding of the fundamentals can surely lead to improvements in process design and control.Successful processes for the agglomeration of fine particles depend on proper control of the adhesional forces between particles, to encourage agglomerate formation and growth and to provide adequate mechanical strength in the product. At the same time the rheology of the particulate system can be critical to the rearrangement of particles necessary to permit densification of the agglomerate and the development of an agglomerate structure appropriate to the end-use requirements.AGGLOMERATION SYSTEMSUltimately, the performance, of any agglomeration process depends on the• characteristics of the particles and their environment. The specific effects, however, are often complex and may be very difficult to pinpoint by simple observation of the process. A typical agglomeration process involves a number of concurrent or consecutive steps - adhesion, growth, compaction, etc., - each of which is affected by the characteristics of the system, but not necessarily in the same way. The effect of particle size, say on agglomerate growth may be quite different from its effect on compaction and its optimum value may differ widely from one stage to the other. Obviously there.is a general need for compromise in the design and operation, of agglomeration systems. Furtnermore, an understanding of the details of the process and their complexities can be critical to process optimization and improved product quality control."

Jan 1, 1989

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

SMCRA contains five principal regulatory provisions that form the basis for its implementation: Performance Standards Performance standard safe intended to ensure that all surface mining is conducted in a way that protects the environment and the public and ensures that the mined land is restored to productive use following mining. Permits Before developing a surface or underground coal mine, an operator must have a permit issued under SMCRA. An application for a permit to conduct a surface coal mining operation is a detailed document that consists of text and numeric data describing the proposed mining and reclamation. Information must be furnished on pre-mining environmental conditions, existing land use, proposed mining and reclamation, how the performance standards will be met, and the post-mining land use. This provides the regulatory authority with the information necessary to determine that the operation can be conducted in accordance with the regulations. Performance Bonds Before a permit can be granted, an operator must post a performance bond sufficient to cover the cost of reclaiming the site in the event the operator fails to complete reclamation. The bond is not fully released until all performance standards have been met and reclamation of the site has been determined to be successful after five years in the East and Midwest, and after 10 years in the arid West. However, the bond can be partially released as various phases of reclamation are completed. Inspection and Enforcement If a violation of SMCRA or of a state surface mining and reclamation law is observed, an inspector issues a notice of violation to the operator. The violation must be corrected within a specific time, and the operator may also have to pay a fine based on the severity of the violation. If the violation is not corrected, acessation order is issued to immediately stop active coal mining, and the operator must pay a fine. If a violation is especially serious (for example, creates an Following reclamation, the land was immediately put back into agricultural production. Today, grain and corn crop yields have continually exceeded targets. 2 imminent danger to public health or safety or causes significant damage to land, air, or water resources) the inspector immediately issues a cessation order. An operator must correct all violations in order to obtain permits for new mines. Lands Unsuitable For Mining Congress recognized that certain coal deposits cannot be mined without permanent damage to unique cultural or natural resources. As a result, SMCRA protects these resources in two ways: It prohibits mining within the boundaries of national parks, forests, wildlife refuges, trails, wild and scenic rivers, wilderness and recreation areas; in areas which will adversely affect sites listed on the National Register of Historic Places; and within a restricted distance of occupied dwellings, public roads, buildings, parks, schools, churches, and cemeteries; and Provides a process that allows anyone whose interests may be adversely affected by proposed mining to petition to have specific lands designated unsuitable for mining.

Jan 1, 1992

By Thomas R. Bur

The order of identification and in same cases the magnitude of the elastic constants of an anisotropic material depends on the orientation of the cartesian coordinate axes with respect to a set of reference coordinate axes within the material; thus confusion will result unless standard orientations are used. In this paper the relationship between the cause (the internal fabric) and the effect (the elastic properties in this case) is discussed for single crystals and for polycrystalline and amorphous materials. While reference axes based on the cause are used in the IRE (Institute of Radio Engineers) standard for piezoelectric crystals) it is shown that a reference coordinate system that would be suitable and practical for all anisotropic polycrystalline and amorphous materials must be based directly on a three-dimensional expression of the effect. The conventions offered are similar to the IRE standards for piezoelectric crystals) but use the elastic coordinates of the wave surface which can be quite readily established experimentally as the reference coordinates.

Jan 1, 1969

The faculty, graduate students, and post-doctoral researchers are an integral part of the Generic Mineral Technology Center for Respirable Dust. More than fifty (50) scientists, engineers, and medical personnel are engaged in respirable dust research at five universities, The Pennsylvania State University, West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University. The expertise, effort and contribution of these individuals has proven to be invaluable in the attack on respirable disease. Nationally and internationally recognized researchers in the areas of particle characterization, interaction of dust and lungs, dilution and dispersion, rock mechanics and continuing education lend their laboratory facilities, equipment and human resources to benefit the mining industry. The expertise and resources of the National Institute for Occupational Safety and Health--Division of Respirable Disease Studies is available through their relationship with West Virginia University.

Aug 31, 1989