Search Documents

This paper describes DRA?s involvement with the expansions at Tati Nickel, Phoenix Mine, that have taken an initial plant design of 3.6 Mtpa (originally built by Murray & Roberts), up to 5 Mtpa, and eventually 12 Mtpa capacity. Initially, the plant could not achieve the design name plate capacity for the first few years of operation, as a consequence of the notoriously hard and abrasive nickel ore affecting primarily the operation of the crusher circuit. In order to extend the life of mine, Tati? assessed and then redefined the mining plan, choosing to increase the Phoenix mine reserves to a lower cut-off grade. In order to increase nickel units produced, the concentrator had to therefore treat additional tonnage at lower head grades. Site investigations and field tests around the comminution circuits are outlined, indicated that the milling circuit could be increased to 650 tph, from the initial design of 470 tph, for a similar feed grade and recovery. A project was initiated to debottleneck the crusher circuit and achieve the new target throughput. (Project 5M). This was followed by a feasibility study of the impact of pre-concentration by DMS, which after promising laboratory tests, was followed up with the installation of a 200 tph ?demonstration? plant. The success of this demonstration plant provided the impetus to expand the supply to the 5 Mtpa mill from a large preconcentration stage. A gyratory crusher (one of the largest and most powerful) will receive ore directly from the open pit operation, feeding into a secondary-tertiary crushing plant followed by a modular DMS preparation circuit. Four large DMS processing modules have been installed to treat the tonnage, with high expected rejection levels. Finally a review of the DMS process capability on an ostensibly disseminated micro-gabbro nickel ore is given, which shows the remarkable impact that preconcentration can have on an operation, both in terms of profitability and a successful process ?expansion?. The performance of the DMS plant has significantly extended the life of mine, allowing the mine to significantly reduce mine cut-off grades and curb its previously selective mining practice.

Jan 1, 2009

By N. T. Beukes

An engineering house?s perspective of required inputs in designing a copper electrowinning tank house and ancillary equipment calls for both understanding of the key fundamental controlling mechanisms and the practical requirements to optimize cost, schedule and product quality. For direct or post solvent extraction copper electrowinning design, key theoretical considerations include current density and efficiency, electrolyte ion concentrations, cell voltages and electrode over potentials, physical cell dimensions, cell flow rates and electrode face velocities, and electrolyte temperature. Practical considerations for optimal project goals are location of plant, layout of tank house and ancillary equipment, elevations, type of cell furniture, required cathode quality, number and type of cells, material of construction of cells, structure and interconnecting equipment, production cycles, anode and cathode material of construction and dimensions, cathode stripping philosophy, plating aids, acid mist management, piping layouts, standard electrical equipment sizes, electrolyte filtration, impurity concentrations, bus bar and rectifier/transformer design, electrical isolation protection, crane management, sampling and quality control management, staffing skills and client expectations. All of the above are required to produce an engineered product that can be designed easily, constructed quickly and operated with flexibility.

Jan 1, 2009

By R. T. Rudd

The impact of slimes-dam formation on water quality and pollution by R. T. RUDD*, B.Sc., AMI (S.A.) CE (Visitor) This paper discusses the mechanics of pollution by slimes dams in the gold- and fluorspar-mining industry, as well as that caused by coal dumps and slurry dams. The effect of coal mining on two typical rivers in Natal is shown and the implications discussed. The implications and trends of sulphates pollution on the Rand Water Barrage in the Vaal River are discussed. The spread of pollutants (sulphates and fluorides) from the Reef and elsewhere, and the impact on urban use and agriculture downstream of the barrage, are illustrated. Conclusions and future policy are outlined.

Jan 12, 1973

By John Freer

The time 06h30 in midwinter is a little early to set out on an excursion from Johannesburg. Yet this was the hour that members, many accompanied by their wives, started to assemble in the parking lot adjacent to the squash courts at the Wanderers Club, Illovo, for a visit to Premier Diamond Mine at Cullinan. All fifty were checked in and aboard the coach by 07hOO. Coffee and sandwiches, served en route by Doris Gardner and Pam Binstead, were most welcome. IMM awards Given below are details of the trust funds, etc., to which applications are invited for grants, etc., payable in 1985. Application forms, which must be returned to the Secretary before 15th March, 1985, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1984

By M. Shamsi, M. Nehring

One of the most challenging aspects in semi-mobile in-pit crushing and conveying (SMIPCC) system design is determining the optimum depth at which to change from a purely truck-based haulage system to a conveyor-based haulage system. We used scenario analysis to determine the optimum transition depth between a truck and shovel (TS) system and a SMIPCC system. Traditional pit-limit algorithms were used to generate the final pit limit on a copper deposit, which was then divided into four pushbacks. The final operating pushbacks (phases) were designed for both TS and SMIPCC. The end depths for each phase are viewed as candidate transition points to switch from the TS to SMIPCC haulage system. Economic calculations were applied for five different scenarios, including adopting SMIPCC from the outset (pure SMIPCC), after the first, second, and third phases, and finally not using the SMIPCC system (pure TS) at all. The analysis indicates that the second scenario, at a depth of 335 m, results in the lowest cumulative discounted cost (CDC). In this case, the CDC is 17.6% lower than that for the pure TS scenario and 10.7% lower than for the pure SMIPCC system scenario.

Sep 1, 2021

By B. McFadzean, N. Patterson, M. Becker, S. Geldenhuys

The retreatment of secondary tailings for platinum group metals recovery presents a range of potential challenges, which vary depending on the nature of the original ore and the type of pretreatment it was subjected to. These challenges include the prevalence of ultrafine particles, which promote slimes coatings on valuable minerals, hinder bubble-particle attachment, increase pulp viscosity, and lead to higher gangue entrainment; surface oxidation of minerals, which alters their floatability; and the presence of deleterious gangue minerals and residual platinum group metal species that are inherently difficult to recover by flotation. This study compares the batch flotation performance across a range of tailings samples from the eastern and western limbs of the Bushveld Complex. A complementary mineralogical analysis was conducted to gain deeper insights into mineral behaviour. The paper evaluates these findings to identify the key factors contributing to poor platinum group metal performance.

Mar 6, 2026

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By C. Hsu

Underground coal gasification (UCG) is becoming more popular as the reserves of good quality, mineable coal are starting to diminish, and yet the global energy demand from coal is still increasing. The purpose of this research project was to investigate cavity formation within a coal block due to the combustion reactions in the context of UCG. The cavity plays a pivotal role in the UCG process, as it is essentially the gasification reactor. Cavity formation in an in situ gasification process using the forward combustion linking method (FCL) had been investigated, and a laboratory model was created to simulate the process. The experiment was performed by drilling a U-shaped tunnel into a coal block, which was then combusted internally with air that was fed through an injection hole. A heating element (at approximately 500°C) was used to supply the required heat for combustion at the base of the injection well. The coal blocks were analysed using micro-focus X-ray tomography. The tomography results showed that the coal tended to crack along the bedding plane after a short duration of combustion, due to either the formation of clinker or the expansion of swelling vitrinite along the horizontal tunnel. The deposit was thicker at the base of the injection well compared to the base of the production well; this may have been caused by the turbulence of the air flow and the relatively high oxygen concentration at the base of the injection well. A comparison of the results with work by Daggupati et al. (2010) showed the same trend, despite the slightly different methodology applied.

Jan 1, 2014

By E. Chisakulo, M. W. Songolo, E. K. Chanda

Zambia’s mining industry has undergone various phases of mineral royalty changes since privatisation. Unlike many analyses that relied on subjective probability, this study employs the cut-off grade and mineral royalty model relationship to investigate how changes in mineral royalties impacted the net present value and cut-off grades of Zambian copper mines between 2008 and 2022. The results showed that net present value decreased by 10.39%, 6.13%, 9.69%, and 6.13% for Barrick Lumwana, Kansanshi, Nkana–Mopani Copper Mines, and Mufulira–Mopani Copper Mines, respectively, while First Quantum Minerals Trident’s net present value increased by 3.40%. Reductions in NPV correspond to higher government revenue, whereas the increase for FQM Trident reduced government revenue. For cut-off grades, returns increased by 0.42%, 1.20%, and 0.42% for Barrick Lumwana, First Quantum Minerals’ Trident, and Kansanshi, respectively, showing how portions of the Zambian copper orebodies accrued to investors, with a corresponding reduction in government revenue. Conversely, reductions of 0.24% and 0.38% for Nkana–Mopani Copper Mines and Mufulira–Mopani Copper Mines indicate that a share of the ore reserves accrued to the government, reducing investor returns. These findings demonstrate that mineral royalty adjustments redistribute economic value between investors and the government, affecting both profit margins and operational decisions. Despite these distributional effects, all projects remained economically viable. The findings underscore the need for an optimal mineral royalty framework that equitably balances the economic value of mineral resources between investors and the state

Jan 30, 2026

Plurigaussian simulation allows constructing lithofacies or rock type models that reproduce the contacts between facies in accordance with the geologist?s interpretation. Its implementation requires inferring the local facies proportions, but the uncertainty in the true proportions is not accounted for. The simpler model with constant facies proportions may not yield realistic results, due to the possibility of obtaining facies at locations where it is geologically unlikely to find them. This article presents a variation of the plurigaussian model, in which the facies proportions are represented by random fields. The realizations can be made conditional to soft geological informati onto account for local changes in the facies proportions. The model is illustrated via a case study of a porphyry copper deposit where four Gaussian random fields are simulated conditionally to drill hole data and to constraints on the probability of finding a given facies at specific locations (control points) in the deposit. Then the first two fields are truncated using the random thresholds defined by the last two, generating a three-facies model. The proposed random proportion model proves to be simple to use and to account for spatial variations of the geological characteristics and for the uncertainty in the facies proportions. Keywords: categorical variable; lithofacies; truncated plurigaussian simulation; regionalized proportions

Jan 1, 2008

By K. C. Corin, M. S. Manono

The mining and mineral concentration of Cu-Ni-PGM sulfide ores in South Africa occurs in semiarid regions. The scarcity and availability of water resources in these regions has become one of the biggest challenges facing mineral concentrators.S Owing to this challenge, concentrators have to find ways through which they can manage and control their water usage. Recycling and re-use of process water in mineral concentrators has therefore become common practice. This practice is beneficial in that it reduces reliance on municipal water, harnesses compliance to stringent environmental regulations on water usage, and it also offers a better response to the Sustainable Development Goals. This could however be somewhat concerning to the operator as recirculated water often has higher concentrations of ions compared to fresh or potable water. The unintended change in the process water quality may potentially affect critical aspects of flotation such as the stability of the froth. This has led to the need to find those process water ions that have the greatest impact on froth stability. Thus, this paper investigates the effect of various ions common in process water of a typical Cu-Ni-PGM concentrator on froth stability. Bubble size, water recoveries, foam height, and dynamic froth stability in both twophase and three-phase flotation systems are used as proxies for froth stability. Findings of this study are deemed crucial towards the development of a process water management protocol in sulfidic Cu-Ni- PGM ore concentrators. Keywords: Bubble diameter, electrolytes, flotation, froth stability, water quality

Jan 1, 2020

By G. B. Abaka-Wood, J. Addai-Mensah, W. Skinner

Recently, coal fly ash has become a potential candidate as a secondary resource of rare earth elements (REE). In this investigation, we studied the recovery of REE from fly ash from a commercial power plant. The specific aim was to assess the technical feasibility of recovering REE from the coal fly ash using conventional preconcentration methods, including gravity separation, magnetic separation, and froth flotation. The experimental results revealed that flotation achieved major gains in REE recovery and upgrading. However, during gravity and wet magnetic separation tests, the bulk of REE reported to the tailings. The results showed significant variations in the performance of the various beneficiation methods investigated. This study has confirmed that existing physical separation methods could be used to recover REE from coal fly ash prior to hydrometallurgical and pyrometallurgical processing, although some challenges persist.

Jan 2, 2022

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By B. Mbuya, A. F. Mulaba-Bafubianda, J. M. Mvita

The paper explains the main effects of input leaching parameters, such as addition of a reducing agent, acidity, agitation, temperature, and leaching system potential, in relation to observed and predicted yields of sought-after cobalt. An artificial neural network coupled with graphical probability networks was developed wherein the abovementioned input parameters were used to predict the percentage of dissolved cobalt. Furthermore, similarities and differences between the Bayesian and neural network approaches in terms of their key outcomes are compared with respect to study of the dissolution of cobalt in sulfuric acid. Key results indicate that there is a need to use neural network results to predict conditions for dissolution of cobalt, while using Bayesian network to explain inferences about conditions of the input parameters, thereby achieving realistic predictions.

Jan 1, 2023

By W. H. Holtzhausen

The purpose of this project was to compare two underground, batch coal haulers ? battery haulers and shuttle cars ? in order to determine the more viable machine to implement. The specific standards for battery haulers were investigated and compared to the requirements of shuttle cars in order to identify the unnecessary expenses related to the legal requirements that are attached to the machines. Costs such as running costs, capital costs, and maintenance costs were researched and compared over a typical life of machine. Average production rates and breakdown times were obtained and used to determine which machine would be more reliable in achieving the required annual production.

Jan 1, 2014

By P. W. J. Delport, E. Du Toit

Investing in a mining venture can be risky and stakeholders need transparent, unbiased reports to understand the Mineral Resources and Mineral Reserves a mining company holds. Readability and textual choice can be used consciously to manipulate perceptions, or it can be done unconsciously. This exploratory study investigates the readability and textual choice of supplementary Mineral Resources and Mineral Reserves Reports of companies listed on the Johannesburg Stock Exchange. The results indicate that narrative manipulation occurs in these reports through word choices that make the reports difficult to read, as well as specific narrative selections. This reduces the informational value of the reports. The results of the study will be useful to various stakeholders, such as mining company management, investors, investment specialists, financial analysts, and even employees and the general community, who all use these reports to make important decisions. It is also useful for the preparers of the Mineral Resources and Mineral Reserves Reports, Competent Persons, and other technical specialists to be aware of readability and that certain textual choices can affect the interpretation of these reports. It is recommended that bodies such as the JSE and the SAMREC and SAMVAL Code committees consider adding a plain language requirement to regulations, guidelines, and codes to ensure transparent, unbiased, and objective reports.

Mar 1, 2021

By M. B. C. Brandt

Richter magnitudes for seismic events were calibrated for use as a Local magnitude scale in the West Rand (WR), Far West Rand (FWR), and Klerksdorp–Orkney–Stilfontein–Hartebeesfontein (KOSH) gold mining areas. Richter magnitudes are currently calculated from seismograms recorded by local surface cluster networks using tabulated calibration values for Southern California, published in 1958. The Richter (1958) model is incorrect for distances of less than 30 km and should be applied only to crustal earthquakes in regions with similar attenuation properties to those of Southern California. When compared to the South African National Seismograph Network (SANSN), the cluster networks, on average, overestimate seismic event magnitudes by approximately 0.1 of a magnitude unit. A calibrated Local magnitude scale was derived by means of a multiple regression analysis between the Local magnitudes reported by the SANSN and the largest zero-to-peak trace amplitudes measured on the cluster network horizontal seismograms, after modelling the attenuation of the seismic waves as these progress from the epicentre to the station position. Magnitudes reported by individual stations for the same event show a significant scatter around the average magnitude owing to the near-surface amplifications of the seismic waves at the recordings sites. Average magnitude should be estimated using as many magnitudes of individual stations as possible to ensure an accurate estimate. Larger event magnitudes should be compared with those recorded by the SANSN.

Nov 1, 2021

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

By E. T. Boome, A. C. Schmidt

P .E.R. T. and how P .E.R. T. techniques can be used in modern mine management by E. T. Boome and A. C. Schmidt Published in the Journal, December 1972 DISCUSSION A. E.W. FLETCHER A.c.S.A.* In making this contribution to the authors paper, I should first like to congratulate them on the clear and yet detailed way in which they have illustrated their subject. I should also like this contribution to be linked with Mr Hazell's paper "Mine Management by Objectives".

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016