Search Documents

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By B. K. Loveday, N. V. Ramlall

A study was carried out to evaluate various batch flotation models for the recovery of minerals in a UG2 platinum ore. The major minerals in a UG2ore can be grouped as platinum group minerals, chromite, and siliceous gangue. This study also examined the entrainment of minerals during flotation. The models were ranked using statistical methods and an analysis of model-fit residuals. Entrainment parameters obtained from model fitting were evaluated for logic using a simple mineral-to-water ratio versus time plot. The foremost conclusion from the study was the importance of entrainment modelling. The measurement of water recovery increased the size of the data-set, and the inclusion of a simple entrainment model was statistically significant. The overall fit to the data was improved, and the entrainment model provided logical information on the recovery of gangue minerals that were not considered to be floatable.

Jan 1, 2015

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

By S. J. Oosthuizen

This article explores the Fray Farthing Chen (FFC) Cambridge process, a novel method for the electrochemical deoxidation of metal oxides in molten salt, discovered at the University of Cambridge in 1997. The process was hailed as a highly promising, potentially low cost, novel method for the production of titanium metal direct from its oxides. The article should inform researchers in the field of some of the challenges in the commercialization of a novel, high profile process involving multiple stakeholders. The author, former senior process engineer at British Titanium Plc, the company originally tasked with commercializing titanium production via the FFC Cambridge process, reviews the latest literature and discusses past and present progress in the pursuit of low cost titanium metal via this process. Topics explored include the history of the process, attempts at commercialization, NASA?s alternative application, and present status of the process. Keywords FFC Cambridge, titanium, molten salt.

Jan 1, 2011

By I. C. Spangenberg

The status of sampling practices in the gold mining industry in Africa was determined as an initial step in a process to standardize sampling practices in the mining industry. Twenty-one gold mines, twenty metallurgical plants, and thirteen laboratories were rated for the potential influence of the relevant sampling errors on each component of the particular sampling system. The findings of the study on the status of equipment, standards, procedures, and management principles were presented in a dissertation (Spangenberg, 20121) and are now used by AngloGold Ashanti?s mines in the quest for correct sampling practices. The information is also used to compile a guideline on leading practice procedures for sampling methods in gold mining. This article is an overview of sampling best practice found in African mining Keywords theory of sampling, best practise, sampling errors, sampling standards.

Jan 1, 2014

By H. Immink

Keywords: Kyoto Protocol, carbon credits, global warming, energy, auditing Climate change is nowadays being taken increasingly seriously, and the link between global warming and the carbon dioxide released in the generation of energy is coming under increasing scrutiny. The Kyoto Protocol was signed in 1997, after five years of negotiation. So far, about 84 countries have ratified this agreement, under which terms developed countries have strict targets linked to their 1990 level of emissions. However, ?greenhouse gas? (such as carbon dioxide) emissions continue to rise alarmingly. According to the World Resources Institute, greenhouse gas emissions in the USA increased 13% from 1990-2002, while Australia recorded a 22% increase. In contrast, the European Union, a Kyoto signatory, has seen a small decline in its emissions during the same period. This is led by the UK and Germany, who reduced their emissions by 15% and 19% respectively. The concept of ?carbon credits? provides a funding mechanism for companies in the developed world to compensate for some of their CO2 emissions by paying companies (trading credits) elsewhere in the world to undertake projects to bring about reductions in emissions. In the southern African mining industry, it will be possible to get refunded for undertaking voluntary emission-reduction projects. Concern about the environment is creating business opportunities. A preliminary calculation has shown that various projects in South Africa (those in the pipeline, with quite a high likelihood of coming off) could earn a combined total of about R2.5-billion, under the initial phase of the Kyoto Protocol's carbon-credit scheme, which allows developed-country companies to trade credits with developing countries. A number of local companies are planning projects that could comply with the Clean Development Mechanism (CDM), in which they will implement techniques to achieve certified emission reductions (CERs) of greenhouse gases. In order to prevent abuse of such a system involving vast sums of money, vigorous audits need to be carried out. A company has to prove it has made real changes and is not simply conducting business as usual under a cloak of claimed environmental improvements. PricewaterhouseCoopers has applied to become one of only a few international agencies that will be accredited to conduct validation and verification of the credits, by auditing what is called the ?designated operational entity?. An independent validator needs to confirm that the project meets the strict requirements of the Kyoto Protocol. The company has to demonstrate that it?s not business as usual. So, if you refurbished every five years, the next refurbishment is not a good CDM project, unless you can demonstrate that you will do something beyond the maintenance - that is what can be registered. So, Kyoto intends to get additional projects going, and the money for that is actually quite good - prices of 14 euros per ton of carbon dioxide not emitted have been seen. The price depends on who takes the risk for non-delivery if a project doesn?t deliver the emission reductions on time. The highly energy-intensive South African mining industry is heavily dependent on coal. There should be many opportunities for the pyrometallurgical industry to come up with creative ideas to reduce emissions, and there is now an additional financial incentive to encourage this. Companies can actually get money in return for doing these types of projects, in addition to the contribution to corporate social responsibility.

Jan 1, 2006

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4 (the main product) and other waste metal chlorides. The TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amount of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify effects of using different feedstocks.

Jan 1, 2015

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl. Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hair-bottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice- Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl' Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hairbottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003