Search Documents

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

By M. Bailey-McEwan

The application of refrigeration on deep South African gold mines is mostly achieved through the medium of chilled water which is produced in central installations either on surface or underground. The amount of refrigeration has been increasing rapidly over recent years, and the total installed capacity on all gold mines now exceeds 1000 MW(R), with annual running costs exceeding R100 million for electricity alone. Hence, there are strong incentives to design such installations for optimal cost-effectiveness. The duty required of these installations varies considerably, owing to daily and seasonal climatic changes and the varying nature of the water demand. It has long been recognized that a computer program to predict installation performance as a whole under any given conditions would be highly desirable. An interactive computer program, CHILLER, is described which enables the user to build an installation, consisting of any configuration of cooling towers, water storage reservoirs and packaged water chilling machines. Externally-dictated conditions such as the weather and chilled water demand must be specified, and all quantities under control of the installation, including internal water flow rates and compressor capacity regulators, must be set. The time-varying performance of the installation can then be simulated. Examples are given of the application of the program in the design of a new installation, and in evaluating the effect of any modifications to existing installations.

Jan 1, 1987

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014

By T. G. Maepa

"The creation of mine excavations alters the stress distribution in the surrounding rock mass. In modern mining, resin-grouted rockbolts are used as a means of support in order to redistribute stresses and reestablish equilibrium in the rock mass. The success of resin-grouted rockbolting depends on the design of the system and the correct installation of the support units.The support design and rockbolt installation procedure at a platinum mine in the Bushveld Complex were investigated. A number of issues that resulted in poor installation were identified, including resin admixture, incorrect length and orientation of support holes, over- or under-spinning of the resin, and incorrect rockbolt tensioning. The support design used at the mine was reviewed and its limitations identified. A number of recommendations were made for optimizing the support design by reducing the diameter of the drill bit and reducing the length of the support holes. These changes will enable the mine to use different combinations of resin capsules. Implementation of the proposed changes will lead to a significant reduction in the cost of installation per support hole, as well as improve productivity and safety.IntroductionThe creation of any mine excavation disturbs the virgin state of stress in the Earth’s crust. This results in stress concentrations that interfere with the stability of the rock mass surrounding the excavation. It is essential to modify the internal behaviour of the rock mass surrounding excavations in order to reinforce the ground and stabilize excavations. Resin-grouted rockbolts are extensively used for this purpose. Esterhuizen (2014) stated that when effectively installed, the rockbolt exerts a clamping force and a bonding strength that keeps the rock mass together. This increases the cohesive strength of all discontinuities in the rock mass and enhances the stability of the excavation. Poorly designed and installed ground support is ineffective and constitutes a safety hazard. It is therefore crucial for every mine to ensure that any form of ground support is designed and installed correctly. This research evaluates the installation of resign-grouted rockbolts and identifies challenges and solutions for improved safety as observed at an operating hard rock mine. The support design used at the mine was reviewed and the design parameters optimized. The outcomes will enhance the efficiency of support and minimize the costs associated with the installation of resingrouted rockbolts."

Jan 1, 2017

By E. Cetin

Orebodies that contain more than one economically important mineral are generally evaluated by parametric cut-off grades. This approach often leads to mis-valuation of mineral deposits because cut-off grades are not based on the grades of each individual mineral and, because of the parametric formulation, are only indirectly related to the individual grade distributions. The only realistic approach is a formulation that accounts separately for each component mineral. The grid search method can be used as a means of multi-mineral cut-off grade optimization in this context. This paper describes the use of the grid search method in cut-off grade optimization for multi-mineral deposits. The authors introduce the general concepts of the method and formulate its application to cut-off grade optimization; they describe a software implementation of the method that can accommodate cut-off grade optimization for mineral deposits that contain up to three economic minerals. Keywords cut-off grade, optimization, grid search, multi-mineral deposits.

Aug 1, 2013

By M. A. Roberts

Oebswana's Jwaneng Mine (south-central Botswana) is the richest diamond mine? in the world and has been contributing substantial revenue to Botswana since the mine started operating in 1982. The resource consists of 3 separate volcanic pipes/vents namely North, South and Centre pipes (2 additional small kimberlite bodies have also been intersected within the mining pit) which erupted through Transvaal strata and the overlying Karoo sediments -245 million years ago. Although earlier drilling and geophysical surveys suggest that the 3 pipes extend to depths greater than 1 km below the surface, the resource is only at an indicated level of confidence to a depth of 400m, and mining activities will start exploiting the inferred resource material below 400m in 2014.

Jan 1, 2010

By Steve Konieczki

[ ] Great Basin Gold Ltd. (GBG) owns the Hollister Mine and operates it through the wholly owned subsidiary Rodeo Creek Gold, Inc. The property is located in northern Nevada on the Carlin Trend gold belt within the historic Ivanhoe Mining District. The mine is located on the western edge of the Northern Nevada Rift, a major north-northwest trending structural zone that has localized middle Miocene volcanic rocks and numerous epithermal gold deposits. The precious metal deposits are low-sulfidation epithermal systems characterized by banded quartz veins with electrum and silver selenides. The Hollister Mine will employ the selective underground mining method of cut and fill. This will be combined with split shooting (resuing mining method) to optimize recovery and reduce dilution. The focus of mining will be on extraction of ?ounces? from the narrow-veins rather than trying to maximize tons. The initial drifts will be excavated along the strike of the vein and then capped with a substantial concrete sill pillar. Back stoping with hand held drills will be used to selectively mine the vein. The stopes will be backfilled with waste rock material. With every lift, an 18 inch concrete cap will be poured onto the backfill waste rock to prevent gold values from being lost into the fill. Targeted ore production rate will be over 400 tons per day. With current ore reserves, project life is estimated to be around eight years; however, Hollister geologists view the site as one of the most prospective systems for bonanza vein deposits in Nevada. Approximately $14

Jan 1, 2008

By M. Nakamura, T. Akamatsu

Embankment dams are often constructed on soft rock foundations in Japan, so it is important to precisely predict deformation of the foundations due to fill placement at the design stage. In order to accurately evaluate the settlement and the strain of the rock foundation surface during construction, the influence of the scattering of the deformability of foundations on the deformation behaviour should be investigated. In this paper, a method of evaluating the settlement and the strain of the rock foundation surface during construction was studied with stochastic deformation analysis considering the scattering of the deformability of the dam foundation. Based on the analytical results, a dam foundation design using the deterministic method considering the scattering of its deformability was discussed. Da in Japan Uferdämme of auf weichen Felsfundamenten gebaut werden, ist es wichtig, die Verformung der Fundamente auf Grund der Platzierung der Aufschüttungen bereits in der Planungsphase genau vorherzusagen. Im Zusammenhang mit einer genauen Beurteilung der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten sollte auch der Einfluss der Streuung der Verformbarkeit der Fundamente auf das Verformverhalten untersucht werden. In der vorliegenden Studie wurde die Bewertungsmethode zur der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten mit Hilfe von Wahrscheinlichkeitsanalysen der Verformung unter besonderer Berücksichtigung der Streuung der Verformbarkeit der Dammfundamente untersucht. An Hand dieser analystischen Ergebnisse wurde das Design der Dammfundamente dann enthusiastisch mittels deterministischer Methoden hinsichtlich der Streuung der Verformbarkeit diskutiert. Comme les barrages en remblai sont souvent construits sur des fondations rocheuses tendres au Japon, il est essentiel de prévoir précisément les déformations des fondations causées par la mise en place du remblayage durant la phase de conception. Afin d’évaluer avec exactitude le tassement et la déformation de la surface du rocher de fondation durant la construction, l’effet de la dispersion de la déformabilité des fondations sur le comportement de déformation doit être étudié. Dans cette étude, l’auteur a étudié la méthode d’évaluation du tassement et de la déformation de la surface du rocher de fondation durant la construction en procédant à une analyse aléatoire/stochastique de la déformation et en prenant en considération la dispersion de la déformation des fondations du barrage. En se basant sur les résultats de l’analyse, la conception des fondations de barrage avec la méthode déterministe considérant la dispersion de sa déformabilité a été activement discutée.

Jan 1, 2003

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

By L. A. Abichequer

ROM grade variability is one of the most important factors influencing plant product recovery. Due to the influence of grade variability on mine profits, it is deemed important to guarantee a proper homogenization of the ore through a well-planned blending and homogenization pile system from which the ore is reclaimed at an acceptable grade fluctuation. This study tests geostatistical simulation efficiency in predicting in situ grade variability. The methodology is illustrated using a data-set from a large phosphate mine in central Brazil. Additionally, real data obtained at the mine site during January and February 2007 were used to derive the actual grades of each pile formed during this period. Each pile was formed by a selection of blocks within a dig line and these lines mined along the year 2007 were also made available. Given the real grades, it was possible to reconciliate and validate the results predicted by the proposed methodology. The main outcome of this study is the opportunity to check the geostatistical simulation as a tool to quantify the variability of the homogenization system.

Jan 1, 2009

Material transfer in underground mines often relies on ore and waste pass systems. Over the years the authors have investigated the design and performance of orepass systems in several Canadian and South African mines. It has been recognized that while most mining operations have either implicitly or explicitly clearly defined objectives, in the design and successfully operate orepass systems there seems to be an absence of a strategy on how to best attain these goals. Consequently, it is not surprising that the majority of operations reviewed by the authors experience a number of problems of varying degrees of severity and economic consequences. This is illustrated by reference to both South African and Canadian operations. The second part of this paper focuses on a review of tactical interventions to rectify orepass problems or mitigate their impact. The paper closes with a framework for a flexible strategy for the design and operation of orepass systems. Keywords orepass; orepass design; orepass stability; orepass rehabilitation; orepass operation; orepass strategy.

Oct 1, 2013

By M. K. Matthews

The use of backfill has important environmental control implications which, although frequently overlooked, can be both beneficial and problematical. Where backfill is widely used, the reduction in stope heat load and improved air utilization influence the overall mine ventilation and refrigeration requirements significantly. A programme of work examining in detail all the environmental consequences of backfilling is currently underway at the Environmental Engineering Laboratory of the Research Organization of the Chamber of Mines. This paper gives an overview of the work and presents some findings. In so doing, the environmental implications to be considered when backfilling are highlighted.

Jan 1, 1988

Determination of mineral composition is of significant importance for the mineral sands industry as this information is required for orebody evaluation, the control of mineral processing plants and the determination of product quality. Mineral processing is made more difficult by the presence of pseudorutile, leucoxene, altered-ilmenite and particle inclusions. The paper investigates the properties of such elements from a single product stream using an MLA approach.

Jan 1, 2007