Search Documents

This paper describes the operating practice and design features of an intensive-cyanidation plant at the East Gold Plant of Vaal Reefs Exploration and Mining Company Limited (V.R.E.M.). After the development oh cyanidation route for the treatment of gold-plant gravity concentrates by the Anglo American Research laboratories (A.A.R.L.), a full scale plant was commissioned at Western Holdings (Welkom Division) Gold Mine in March 1977, and the V.R.E.M. plant was commissioned in August 1981. Although the gravity-concentration route does not now enjoy the prominence of former times, in an existing conventional plant the intensive-cyanidation route can successfully replace mercury amalgamation.

Jan 1, 1984

By R. K. Brummer

The support of stopes and tunnels in South African gold mines subject to rockburst damage requires special attention. The interaction of a seismic wave with either a stope or a tunnel is subject to a number of variables, namely the distance from the source of the event, the ground velocity, the orientation of the excavation with respect to the direction of the seismic wave, and the geology and fracturing around the excavation. This paper discusses these factors in relation to the support requirements in stopes and tunnels. The need for the integration of hydraulic props with stope support and the use of yielding anchors for tunnel support are emphasized.

Jan 1, 1988

By R. R. Mankowski

The work described here is an extension of current theory applied to obtaining the power dissipated at the wavefront of a transverse disturbance traveling along a mine hoisting cable. A previously derived empirical relation is adapted to the present problem, and is solved by use of a Lagrange-type reference frame moving with the wavefront. As a result of tie limitations inherent in the original relation, only a lower-bound for the domain of predicted power losses is defined. A qualitative assessment of conditions leading to the undesirable effects of internal frictional losses at the wavefronts are discussed in terms of the operating environment found on typical mining installations

Jan 1, 1990

By G. B. Lundstrom

SYNOPSIS For some time, Vaal Reefs South has operated blindhole borers successfully as an integral part of the mining cycle of operations. To date, over 13 000 m of mechanized boxholing has been completed, and from time to time impressive performances have been achieved. The paper describes the machines, the modus operandi, and the structure of the boring organization at the Mine, with some of the results recorded. The Mine recently took delivery of two new machines with interesting design features. The introduction and early experiences with these two machines are also described.

Jan 1, 1985

By J. T. Davies

Note: Melting techniques in the iron foundry by J. T. DAVIES* INTRODUCTION The selection of melting equipment for use in an iron foundry has for several years been the subject of numerous discussions, papers, and conferences. The controversy that has raged throughout the world has been brought about by the following factors: IF AC Symposium The 2nd IF AC Symposium on Automation in Mining, Mineral and Metal Processing will be held from 13th to 17th September, 1976, at the Carlton Hotel, Johannesburg. Advance registration takes place on 12th September, 1976. World phosphates The Minerals Bureau of the Department of Mines has released the second publication in its series of reports on the economic aspects of minerals that are of particular importance to South Africa.

Jan 7, 1976

By M. Reuter

This paper gives an overview of some criteria for the selection of processes for the recovery of lead and zinc from various raw materials and/or intermediate products. A glossary of possible processes and process variants, is presented and discussed, as well as the way in which these are interlinked. Recent developments in metallurgical process synthesis are also discussed, and the results produced by an eco-techno-.economic synthesis procedure for process routes in zinc metallurgy are given briefly. The way in which such a synthesis can complement a life-cycle assessment (LCA) of zinc-producing technologies is also described.

Jan 1, 1997

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By C. O. Beale

This, the second and final part of a review on the subject(the first part was published in the March issue of this Jouma/), deals in detail with the 9 copper-producing companies in the Republic of South Africa. These are The Phosphate Development Corporation, Prieska Copper Mines (Pty) Ltd, Black Mountain Mineral Development Co. (Pty) Ltd, Rustenburg Platinum Holdings Ltd, Impala Platinum Holdings Ltd, Western Platinum Ltd, The O'okiep Copper Co. Ltd, Messina Ltd, and Palabora Mining Co. Ltd. The following are described for each company: background, development, geology, mining, concentration, and current situation. The last-mentioned company, being South Africa's largest producer, is dealt with in greatest detail.

Jan 1, 1985

By J. Zwartendyk, A. Azis

Optimizing the public gains from the exploitation of mineral resources By Dr A. AZIS and Dr J. ZWARTENDYK Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived.from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit. The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits. Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels. Computer simulations can be run of discounted cash flow models at various taxation levels to showthe impact of taxation changes on future tax revenues.

By R. J. Dippenaar, J. C. van den Berg

This paper describes an investigation into the prereduction of hematite fines in a fluidized-bed reactor as a means by which they can be prepared for direct smelting in a transfered-arc plasma furnace. A single-stage fixed fluidized bed reactor using the in situ gasification of coal was employed. It is shown that the hematite is reduced to magnetite at 1000 QC, the degree of reduction being limited by the inherent shortcomings of a single-stage reactor in which both the gasification and the reduction reactions have to occur. Methods by which the degree of reduction can be increased are suggested. The gasification process was studied in some detail, and three different reducing agents are compared. The dominating effect of the Boudouard reaction on the behaviour of the fluidized bed is clearly illustrated. Non-coking coals of high reactivity are best suited to this process, a finding that would complement the trend away from coke as a metallurgical reducing agent.

Jan 1, 1989

By M. Cortie, L. Iorio

The amount of nitrogen contained in an austenitic stainless steel affects its properties significantly. The maximum content of nitrogen feasible in a range of experimental low-nickel austenitic stainless steels containing significant additions of copper is evaluated The nitrogen content is calculated based on published interaction coefficients, and by use of the FACT thermodynamic computer program and database. The differences between the two methods of prediction can be attributed to inaccuracies in the published interaction coefficients. The calculated nitrogen contents of some experimental alloys are compared with the actual nitrogen contents obtained when the alloys were produced in an induction furnace. The actual nitrogen contents obtained were higher than those predicted by either method, and this is believed to be due to a super saturation of nitrogen occurring in the melt, which was not relieved during the short period in which the charge was molten. It was evident that the experimental alloys can contain between 0,25 and 0,40 per cent nitrogen (depending on temperature, composition, and nitrogen pressure) when melted in a sealed induction furnace, and this is more than adequate for the purpose of forming and stabilizing the austenite phase.

Jan 1, 1994

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

By A. N. Brown

The importance of the minerals industry in the economy of the country is discussed, and the tremendous changes that have taken place over the past two decades, including the widespread application of computers and the use of mechanization, are outlined. A discussion of the future of the minerals industry points out that, with the rise in the price of gold, the life of the gold-mining industry can be expected to extend beyond that previously predicted, and that the demand for uranium, which has been depressed, is uncertain. As a result of the oil crisis, the demand for coal has increased and large expansion programmes are planned. These involve coal exports and the use of coal for the generation of electric power, for the production of liquid fuels, and for the smelting of metals. Technical challenges face engineers in every avenue of the minerals industry: in deep gold mines, underground coal mines, strip coal mines, and open-pit mines. Studies indicate that only one-third of the demand for trained mining and metallurgical engineers is being met and that the position is worsening. However, there are indications that the industry is succeeding in attracting more engineering students, and the supply is expected to improve. These efforts should be co-ordinated, expanded, and intensified. There is a need to ensure that sufficient teaching staff of the right calibre and experience are attracted to universities and technikons. The first degree course is comprehensive and basic, and specialization through post-graduate study should be encouraged. The influence of national service on the education and training of engineers is discussed.

Jan 1, 1982

By Dick Stacey

Many open pit mines are now being mined at very significant depths, often at depths far greater than was originally planned. Even deeper open pits are also being planned, to depths that would be considered deep by underground standards. The heights of the resulting rock slopes are usually beyond the current experience and knowledge base. The exceptions are, perhaps, some very high and steep natural rock slopes. These natural rock slopes are also assuming greater significance owing to pressures of infrastructure development and consequent exposure of such infrastructure to the hazards of slope failure and landslides. Developments in road and rail infrastructure are also resulting in higher rock cuttings. Present understanding of the mechanisms of slope behaviour and failure for high slopes, and for slopes subjected to high in situ stress conditions, appears to be lacking. If the mechanisms of slope behaviour are not well understood, the validity of commonly applied methods of analysis of the stability of such slopes may be questionable. The papers in this specialist International Symposium, including papers on mechanisms and monitoring techniques, and case studies will contribute to the understanding of these issues. The Symposium has attracted good international participation, from both the attendance and authorship points of view. We are very grateful to all presenters and delegates for taking timeout of their very busy schedules to come and share their knowledge and we hope that all will benefit from this event. Thanks are due to the Organising Committee and to the members of our International Advisory Panel for the ideas, the contacts and the badgering, and to the Secretariat of the South African Institute of Mining and Metallurgy for the organisation.

Jan 1, 2006