Search Documents

By C. T. O’Connor

Since the first IMPC took place in London in 1952 there have been many developments in our understanding of flotation, both in terms of chemical and physical factors influencing the process. Many of these developments have been captured in the proceedings of thirty congresses that have taken place since that first event, as well as in numerous journal papers and special volumes dedicated to flotation. This paper attempts to highlight the individual contributions which many eminent researchers and engineers have made over the past 70 years towards extending our understanding of, especially, the effects of chemical factors on flotation. Although the focus is mainly on more fundamental aspects, it seems that the ‘pull’ of practice has often preceded the ‘push’ from laboratory-based research. As the fundamental understanding of the role of chemical factors on flotation continues to be developed, the major challenge remains to transfer this knowledge effectively into the domain of operations of this profoundly complex process.

Jan 1, 2020

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

1. Book reviews Physiochemical properties of molten slags and glasses, by E.T. Turkdogan. London, Metals Society, 1983.516 pp. £35. Reviewer: A.F .S. Scboukens Microstructural characterisation of metals and alloys, by P.E.J. Flewitt and R.K. Wild. London, Institute of Metals, 1984. £14. Reviewer: M.P. Sbaw Metallurgical applications of magnetohydrodynamics, edited by H.K. Moffatt and M.R.E. Proctor. London, Metals Society, 1984.346 pp. U.K. £35, U.S. $70. Reviewer: N.A. Barcza Extractive metallurgy symposium. Proceedings of a meeting on 12-14 November, 1984, organised by the Melbourne Branch. Parkville (Victoria), Australasian Institute of Mining and Metallurgy, 1985. Reviewer: B.K. Loveday Conference on gold mining, metallurgy and geology. Proceedings of a meeting on 9-11 October, 1984, organisedby the Perth and Kalgoorlie Branch. Parkville (Victoria), Australasian Institute of Mining and Metallurgy, 1985. Reviewer: B.K. Loveday Corporate policies for the 1980's in the steel industry, by Patrick Genevaz in collaboration with B.A. Bloom. La Chambre des Cartes, 26 rue de Piepus, 75012 Paris (France). U.S.$7oo, additional copies $140. Reviewer: D.C. Maree Mineral processing technology, by B.A. Wills. Oxford, Pergamon Press, 1984 (3rd edition). 629 pp. Hard cover £31.50, soft cover £9.75. Reviewer: B.K. Loveday Ma1lllgement information-ma1lllging for improYement, volume 2: symposium proceedings and additional papers. edited by M. Hammond. Doncaster (England), The Institution of Mining Engineers, 1984. 86 pp. £60 for vols. 1 and 2 (124 pp.). Reviewer: M.J .R. Meyer 2. Recent publications Tins and its and its uses no. 144, 1985. This issue by the International Tin Research Institute (Fraser Road, Greenford, Middlesex, UB6 7AQ, Canadian minerals yearbook 1983-84. Department of Energy, Mines and Resources Canada, Mineral Report 33. Ottawa, Canadian Government Publishing Centre, 1985. $35.40. 82 Year 1984, edited by 1.0. Jones and RM. Louthean. Kalgoorlie (Australia), Western Australian School of Mines, 1985. 100 pp. Johnson Matthey Chemicals 1984-85, issued by Matthey Catalogue Sales (Orchard Road, Royston, Hertfordshire SG8 SHE, England). 416 pp. South Africa's mineral industry 1984. Johannesburg, Minerals Bureau, 1985. 190 pp. Coal 1985. Operating and developing coal mines in the Republic of South Africa. Johannesburg, Minerals Bureau, Directory 2/8S. 1985. 72 pp. Gold 1985. Operating gold mines and gold recovery plants in the Republic of South Africa. Johannesburg, Minerals Bureau, Directory 3/8S. 98 pp. 3. New journal Pergamon Press, New York, have announced the publication of a new quarterly known as the International Journal of Plasticity. 4. Mintek reports Report M93D Hydrochloric acid leaching and low-temperature roasting of tin-tungsten concentrates from Van Roois Vley. (First issued April 1983.) Report M99D The upgrading of coarse kyanite crystals. (First issued Report M105D The development and installation of a microcomputer based data logger, and the analysis and evaluation of data. (First issued July 1983.) Report M109D The remelting ofsi/iconfines. (First issued July 1983.) Report M180 An assessment of available corrosion inhibitors for the reticulation systems of South African gold mines. Report MW1 Quantitative assessments of abrasive and impactive wear from ball-size distributions in rotary mills.

Jan 1, 1985

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By A. L. Hinde

A review of real-time particle size analysers A. L. HINDE,. B.Sc., A.R.C.S., D.I.C., Ph.D. The physical principles of different sizing techniques are critically examined in order to evaluate the suitability of the techniques for real-time particle size assessment. Examples of both successful and unsuccessful attempts at producing an acceptable real-time sizer are described in order to delineate the difficulties involved in making rapid and accurate size measurements. Only two of the examples described have proved to be suitable for on-line particle size monitoring, namely the "MintekjRSM Onstream Slurry Sizer" manufactured by Cartner Group, Ltd., and the "PSM System 100" made by Autometrics Co. Both these commercial systems are capable of assessing particle size with an accuracy comparable with that obtained by routine sieving and weighing. The "PSM System 100" has been used successfully for automatic control of grinding circuits. Economic benefits derived from this system, operating under rigorous plant conditions for several months, have proved that real-time size analysers are of significant value to the mining and metallurgical industry.

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By John Freer

On 25th November, 1983, nearly forty members of The South African Institute of Mining and Metallurgy, together with Doris Gardner and Judith Money from Kelvin House, travelled by luxury motor coach to Secunda, there to visit the coal-mining and conversion operations of Sasol Limited.

Jan 1, 1984

VISIT TO HENDRINA POWER STATION AND OPTIMUM COLLIERY A visit to Hendrina Power Station and the Optimum Colliery, contractually committed to supply the coal for the power station, took place on the 20th September, 1972. INTERNATIONAL IRON AND STEEL CONGRESS This congress will be held in Dlisseldorf from May 23rd to 30th, 1974. The main theme is "Metallurgical Technology of Iron and Steplml1king".

By T. P. Chidakwa, T. R. Stacey

This study investigated the corrosion rates of various steel types and coatings used for friction rock stabilisers in a deep-level gold mine under diverse underground environmental conditions. Testing was conducted in situ within ramps, intake airways, and exhaust airways, and through simulated laboratory experiments. Results revealed that environmental variations significantly influence the corrosion performance of different materials and coatings. Duplex coatings, made up of galvanised steel with an organic paint layer, demonstrated the highest corrosion resistance. Zinc-based coatings provided moderate protection, while 3CR12 stainless steel and uncoated S420 carbon steel exhibited comparatively poor resistance under both aqueous and atmospheric conditions.

Mar 4, 2025

By P. J. Brereton-Stiles, C. J. Hockaday, I. J. Barker, M. S. Rennie

This paper reports on studies that have been done on the electrical conduction in silicon, ferro silicon, and charge chrome furnaces. A system has been developed that can distinguish between normal resistive conduction and arcing, and this was used to quantify in particular the relative amount of arcing that takes place in these furnaces. It was found that silicon and ferro silicon behave similarly and exhibit a relatively large amount of arcing. Charge chrome on the other hand exhibits considerably less arcing, and the extent of this arcing is highly correlated with the tapping of the furnace. The arcing measurements can also be used online in the control of the furnace, both for the electrodes and electrical circuit, and for the raw materials.

Jan 1, 2007

Visit to Premier (Transvaal) Diamond Mining Company Limited On the 14th February, 1973, 44 members of the Institute were the guests of Premier (Transvaal) Diamond Mining Company Limited. Metrication News PRESSURE GAUGES There appears to be doubt in some circles about the general acceptance of the pascal (Pa) as a unit of pressure and stress. NATIONAL INSTITUTE FOR METALLURGY / NASIONALE INSTITUUT VIR METALLURGIE REPORT. VERSLAG No. 1430 THE USE OF THE EKCO MINERAL ANALYSER FOR THE DETERMINATION OF COPPER AND ZINC IN THE PRESENCE OF IRON 27th June, 1972 Investigator: Gisela Domel SYNOPSIS The Ekco Mineral Analyser-a portable, radio-isotopic X-rayfluorescence instrument-is briefly described,

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By M. Aatach, St. Gaydardzhiev, M. Kadiyski, E. Visariev, V. Stoilov

Detailed process oriented characterisation on representative samples from plant survey of the slag flotation plant belonging to Aurubis, Bulgaria has been realised in order to evaluate the mineralogical occurrences of Cu, Ni, Mo and Co bearing phases. The slag subjected to flotation consisted in majority of fayalite, magnetite-iron oxides and a glass-like phase. Ni and Mo have been found to be closely associated to magnetite and fayalite. The tailing from the slag flotation has been subjected to sulphation roasting followed by water leaching as a hydrometallurgical means to recover the remaining Cu, Mo, Ni and Co. Based on the various sulphation roasting conditions (acid dosage, duration, temperature) copper, nickel and cobalt were brought to solution to a different extent. Molybdenum was the most difficult to be rendered soluble due to its close association with iron, suspected to form an insoluble compound with it. Sulphation roasting performed at 350ºC has secured the best extraction degree for Cu, Mo and Co, while maximum recovery of Ni has been documented when roasting was done at 150°C. Keywords: Copper slag; characterisation; SEM; roasting; metals leaching, hydrometallurgy 16(2), 153–65.

Jan 1, 2020

By John Freer

As an innovation on the annual programme, the Excursions Sub-Committee organized a social get together of the Institute's Councillors and their families on Sunday, 27th February, 1983. Asian Mining - change of date The Second Asian Mining Conference, previously announced as being held in Manila, The Philippines, from 5th to 8th November, 1984, will now be held in Manila from 11th to 14th February, 1985.

Jan 1, 1983

By G. H. Lind

New South Wales has a successful history of pillar extraction stretching back more than 60 years. Various methods of pillar extraction ranging from the rib pillar methods (such as the Wongawilli system) to the more recent pillar stripping techniques (similar to those used in the USA) are discussed in this paper. These discussions are based on the experiences of the author stemming from a recent research tour of seven underground pillar extraction operations in New South Wales as part of the Coaltech 2020 collaborative research initiative. Some operational issues of each site visited are presented before some general comments pertaining to the overall success of pillar extraction in New South Wales are discussed. Generally pillar extraction in New South Wales is on the decline in favour of longwalling. However, the pillar extraction that is conducted is done so along specific guidelines to ensure their success, and these are also discussed.

Jan 1, 2002

By David J. Haddock

On Wednesday, 6th July, 1988, 28 members of the Johannesburg Branch of The South African Institute of Mining and Metallurgy and their guests assembled at the Rand Refinery Sports Club, which is situated within the Refinery complex, to hear Dr Daniel Polnow, General Manager of the Refinery, give a very interesting lecture on the Rand Refinery Complex and its activities. Accounting for gold The South African Institute of Mining and Metallurgy will be holding a 3- or 4-day school in the third week of May 1989 on the topic 'Accounting for Gold'.

Jan 1, 1988