Search Documents

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By J. Hazen, R. Jenner

This project was developed at the PCS Phosphate Mine in Aurora, NC. This site includes a surface mining operation, beneficiation plant and chemical processing facility located in the coastal plain of eastern North Carolina. The phosphate ore being mined at this operation is a 10 to 12 meter (35 to 40 foot) thick colloidal deposit located approximately 30 meters (100 feet) below the ground surface. The ore is pumped to the beneficiation facility where it is separated into clay, sand and concentrate streams. The concentrate product is utilized at the chemical plants to produce a wide range of products including fertilizer, industrial phosphates and animal feed products. The Cyclone Dike Builder (CDB) project developed a technique for dewatering the beneficiation tailing sand stream and providing innovative placement for dike construction. Future material balance requirements at the PCS Phosphate mine required an improvement in tailing sand placement technique to accomplish strategic objectives. The water volume of the sand slurry forces significant quantities of sand out of the dike profile during deposition. PCS Phosphate and MetPro Supply of Florida developed a mobile high-density hydro-cyclone station to remove most of the water and significantly increase the density of the sand being placed for dike construction. This high-density sand slurry is then effectively controlled using minimal heavy equipment operation.

Jan 1, 2004

By Fred T. Towne

Recent developments in fine grinding by the means of mechanical impaction are the result of continuing improvements in modern machine construction. This is especially true when related to the bearings and mechanically operated parts of impact mills. These improvements allow manufacturers to increase the speeds of the impacting members Most of the more common forms of size reductions, such as percussion, pressure, friction and sectioning, or cutting were at one time accomplished by human hands. These actions were transferred to machinery. Originally of limited application, their use widened as industrial materials and construction became more sophisticated.

Jan 1, 1965

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By A. E. Hunt

Over the past twenty-live years since large scale truck haulage in open-pit mining began, the periodic introduction of Larger capacity vehicles has provided increased productivity and reduced costs. WISEDA Ltd. has introduced a 220 ton capacity, two-axle rear dump, diesel-electric truck for the world-wide large open-pit mining industry. Design features and components selected in the development of this vehicle will be presented along with operating experience and a brief history of rear dump truck evolution.

Jan 1, 1983

By Anne Kathrine Kalager

"Stretching from Norway’s capital, Oslo, to the city of Ski, a new railway line is under construction with a 20 km long hard rock tunnel. This is a major project with high demands regarding quality, cost and schedule. In addition, restrictions concerning locations close to sensitive urban infrastructure require execution with the highest level of precision and expertise. The new double track railway line forms an important part of the intercity rail development southwards from the capital and includes the longest railway tunnel to date in the Nordic countries. With its novel methods and solutions, this project offers a model for future railway project developments in the region. This paper provides general pertinent details and facts relating to this current railway project and includes a description of the project with information relating to concept and design of the tunnels, geological conditions, particular challenges, selected tunneling techniques and contracting strategies. THE FOLLO LINE PROJECT The Follo Line is a new 22 km long double track railway line under construction between Oslo Central Station and the city of Ski. The project is divided into four subprojects, as shown in figure 1. The main part of the project consists of a 20 km long hard-rock tunnel, which will be the longest railway tunnel in the Nordic countries to date.The Østfold Line is the existing double-track railway line running between Oslo Central Station and Ski serving 12 local stations. The new Follo Line will offer a direct service, without stops, between Oslo Central Station and Ski and reduce the travel time from 22 minutes to 11 minutes. After completion of the Follo Line, these two railway lines will, in combination, more than double the capacity for train transport in the region south-east of Oslo."

Jan 1, 2016

By Martin G. Taube, Dwayne A. Lewis

Drainage improvements at O’Hare International Airport, Chicago, IL included the installation of a drainage and storm water system to control the over?ow from nearby Willow Higgins Creek. This involved construction of a weir structure at the creek and the channeling of water from the weir to a newly constructed reservoir via three, 3.7-m(12-ft) diameter, underground storm sewer lines. The sewer lines passed beneath an existing, 2.3-m (90-inch) diameter high-pressure water main, which was to remain in service throughout sewer line installation. The soil composition around the water main ranged from medium stiff clays to silty sands and sandy silts. Triple-fluid jet grouting was used to stabilize the variable soil profile beneath the water main in preparation for tunneling and installation of the sewer lines. The varying soil strata presented a challenge to the project team to establish a constant set of jet grouting parameters throughout the stabilized zone while keeping within the specified unconfined compressive strength range for the stabilized zone of 690 to 1,380 kPa (100 to 200 psi)at 28 days.

Jan 1, 2003

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By W. G. Lacy

Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the and to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area prompted by foundation failures and breaking, of buried service lines serve to illustrate some of these relationships between the geological environment and history, and engineering problems.

Jan 1, 1963

By Richard L. Ash

Less than optimum production in mining always results when poorly blasted material is provided at loading points. More often than not the cause is due to blasting founds that fail to fully control and utilize explosive energy. In many cases the problem exists because too few blasters understand how blastholes actually break rock and recognize that blasting is a three-dimensional process in designing their blasts. To better understand how blasts can be more effectively designed the two major rock breakage processes are described. In addition, the respective contributions of the borehole and detonation pressures are defined as are the specific roles of the several important blasting design variables. The concept of stiffness as an engineering principle and its significance in blasting design is introduced for explaining the breakup of rock. Basic guidelines for affecting control over fragmentation and side effects like over-break are offered.

Jan 1, 1975

By Edwin J. Connell, O&apos

Investment in mining and related process facilities will be more costly and complex in the 1980s than ever before. Interest rates and inflation are soaring; regulations are expanding; and in order to achieve economies of scale, plant facilities and mines are getting larger. As the pace quickens, the time/cost circuit closes around the resource owner or developer. Larger modern projects cost more money and take more time to build. The longer it takes to bring a project onstream, the more it costs in interest, escalation, and lost production. One solution to the time/cost squeeze is to take advantage of systems developed by major contractors serving the mining industry. These contractors have been serving clients in planning and executing large and small projects for many years. They have developed systems which, if applied at an early point in the project's life, can be a significant benefit in development of mineral resources. The systems involve performance of feasibility studies, economic evaluations, and the project installation itself. First the Feasibility Study Feasibility studies can minimize risk through systematic evaluations while progressing toward the ultimate objective-an operating plant. Normally, studies are initiated with a minimum amount of specific information and a maximum number of as¬sumptions. Through the course of the study program, assumptions are continuously confirmed, refined, or rejected by facts until a sound basis for decision is available. High on the list of cost effective tools for evaluation is the use of a geostatistically derived sampling program that provides a highly accurate ore reserve estimate for economic evaluation. When a predetermined sample of data from the drilling program and bench-scale or pilot-plant tests are received, a detailed feasibility study may be started. This study can involve design of the mine,

Jan 10, 1980

By Brahm D. Prasad

As in other mineral deposits, variation in bitumen saturation, thickness of ore and discard occurs throughout Alberta's Athabasca Oil Sands deposit. The economic stripping ratio developed here to determine surface mineable limits takes into account capital and operating costs, crude oil prices, quality of ore, thickness of overburden, and thickness of inter-ore waste. The surface mining systems employed to remove bituminous sands (oil sands) from huge mines at depths of 60-70m use gigantic draglines, bucket wheel excavators and reclaimers, and large mobile equipment.

Jan 1, 1982

By Fernando Pendás, Jorge Loredo, Alumudena Ordóñez

Water derived from mine-tailings typically contains high concentrations of H+, SO4, Fe and other metals, and it frequently suffers a decline in pH and the development of acidic mine drainage (AMD). A paper describing the results of a series of laboratory experiments with real AMD and a subsequent field trial with a in situ pilot system to assess a potential method for remediating tailings-derived water is presented here. After testing different organic substrates, residence times and flow conditions during two years to determine the most appropriate treatment for a polluted Spanish AMD, a pilot scale system combining SAPS, ALD, oxidation/sedimentation ponds and an anaerobic wetland was designed. Preliminary analyses of effluent samples indicate acidity and metal removal is occurring within the system, although sulphate removal is not complete. The results of this small-scale field trial suggest a potential cheap, long-term alternative for remediation of acid mine drainage.

Jan 1, 2000

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

Although mineral commodities used to play and still play a very crucial role in the development of civilization over the centuries, their extraction, transportation, transformation and use are at present sources of great concern in terms of sustainability. Some of the most discussed environmental problems are in fact closely related to the utilization of minerals as materials and fossil fuels. The paper analyses the origins of sustain-ability weakness of mineral supply through Environmental Economics models, which have interpreted the phenomena of pollution and non-renewable resource depletion as a market failure. Conventional market tools have proved to be unable to perform an optimal allocation of those resources that are priceless or have open access. An external intervention is needed in order to reduce the excessive exploitation of environmental and natural resources. Some of the solutions proposed by policymakers and subsequently implemented by governments are briefly considered and the achieved results are discussed. In several cases the public intervention, where the attempt was to restore the sustainability conditions, has failed. Restrictive environmental protection regulations have resulted in severe limitations to the mining activity, without, on the other hand, achieving the expected results in terms of sustainability. Some of these regulations instigate unfair international competition practices among those producers who do care about the environment, but who have high production costs, and those who supply cheap raw material but whose low costs hide heavy environmental impacts. Nowadays, most of the world?s supply of minerals is being produced in developing countries, with severe global environmental impacts. As effective tools for monitoring the problem, sustainable development indicators could be used by policymakers to duly associate the comprehensive environmental impacts for each mining product, depending on its origin and extraction history.

Jan 1, 2003

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

Jan 1, 2006

By W. N. Brown

One of the seemingly eternal problems with which we are frequently faced is that of providing adequate and economical warehousing facilities to store large quantities of bulk product. Seasonal consumption, transportation, marketing, and other factors very often dictate extensive product warehousing requirements for an operation geared for steady, year-around production of a material requiring weather protection during storage. Fertilizers such as potash and urea are examples of such products; the consumption of these materials is extremely heavy in the early spring at which time the materials must be placed in the soil, whereas, for obvious operating efficiencies, production is more or less constant for a given operation throughout the year.

Jan 1, 1961

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981