Search Documents

By A. Bascetin

The human requirements have increased rapidly depending on population density and urbanization thus industrialization has grown steadily. As a result of the situation, the greenhouse gas emissions into the atmosphere and the global warming have increased slowly. Today this effect has continued to increase. Therefore, the effects of greenhouse gases in all areas of production must be controlled. The study presents the methods of determination the CO2 emissions (CO2-e) and energy consumption in aggregate production. The aggregate constitute approximately 70% by volume of concrete that has widespread use as construction material in the world. One of the most important elements in today's terms is sustainable use of resources and minimum CO2 emissions (CO2 + CO + NOx + CH4.vb.) at every stage of production of aggregate. Therefore, these elements must be taken into consideration in the aggregate production standards. The choice of production method of aggregate is very important for optimum use of energy and effects of greenhouse gas emissions. So the properties of the aggregate material must be known well to obtain the target. Within the scope of this study, the unit value of CO2-e that release when the production of aggregate in different formations is determined for our country. Thus, the effects of green house gas emission can be evaluated according to the characteristics of material in aggregate production planning. In this study, energies consumed during the production of aggregates at a quarry in Istanbul Cendere region were investigated by taking the different formations encountered at the quarry into consideration. The unit CO2 emission values per ton of produced aggregates were calculated as a result of this investigation. Besides, energy consumption values of previous months at this quarry were taken and the unit CO2 emission values were also calculated.

Jan 1, 2011

By F. M. Doyle, P. E. Richardson, E. Peters

A number of studies have attempted to correlate the semiconducting properties of mineral sulfides with their chemical reactivity. Frequently such studies are conducted on polished or abraded electrodes. Defects produced by abrasion may mask the influence of the semiconducting properties of electrodes, e.g., by pinning the Fermi level at the surface or by reducing the lifetimes of photogenerated charge carriers. It is shown that pyrite and galena electrodes have photocurrents that are extremely sensitive to abrasion of the electrodes. On freshly fractured galena surfaces, the space charge layer is readily polarized. Wet-abrasion is shown to produce a relatively thick ptype layer on galena electrodes and this p-type layer has a pronounced effect on the photoresponse. On freshly fractured pyrite surfaces, the Fermi level at the surface is pinned by a surface state. Wet-polishing reduces the magnitude of the photocurrent by over an order of magnitude.

Jan 1, 1993

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

Load transfer capacity and failure mechanism of a fully grouted bolt installed across joints in shear is evaluated both experimentally and numerically in five types of bolts (low strength steel, rebar bolt and high strength steel). The strength of the concrete, bolt profile configuration, bolt mechanical properties and bolt pretension load play significant influence on the shear resistance, shear displacement and failure mechanism of the reinforced medium. Failure location moves towards the bolt joint intersection due to the increasing shear load, shear displacement and axial load developed along the bolt. Finally bolt failure occurs as a result of the induced axial and shear stresses acting between hinge points on either sides of the shear joint plane.

Jan 1, 2006

By D. J. DeLeo

In recent years the hue and cry of American industry concerning the pressure of foreign competition on the domestic marketplace has become all too familiar to most of us, as we are all well aware, the steel industry has not been exempted from this pressure, reduced production levels, work force cutbacks, and in some extreme cases, plant closings and company liquidations have resulted, new regulations governing imports and quotas have been enacted, foreign trade agreements reached, and more strict regulation enforcement practices undertaken, despite these, and other measures, the impact of aggressive foreign competition has not lessened, the concensus of numerous management consultants is that in order to successfully cope with these problems we must draw on all available technology to provide the tools which will enable us to enhance our management effectiveness, one area requiring particularly close attention in any mining operation is that of managing critical resources - namely time, energy and equipment in a fast and efficient manner, In mining, with critical resources deployed over a large geographical area, any degree of success involved with resource management is dependent upon knowing the current status of all work related activities, if we, as mine operators, are to be more successful in this area, additional tools are a necessity and modern technology has provided a multitude of new options from which to choose.

Jan 1, 1985

By Kostas Fytas, Sebastien Perreault

This paper presents EOLAVAL, an integrated mine ventilation design software. In its new expanded version it is a user friendly and fully interactive computer package. The features of the new version are a graphics interface fully compatible with Autocad files, an integrated database of fan characteristics and the optional use of the thermodynamic approach in carrying out network simulations. This software can be used in underground mine ventilation planning: mine ventilation network analysis and simulation, economic design of airways, auxiliary ventilation design, calculation of a mine air heating plant, and evaluation of the natural ventilation and pressure losses in a mine shaft. This paper presents a case study illustrating the use of the computer package in mine ventilation design.

Jan 1, 2002

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By J. Mark Richardson, Mary S. Sredanovic

The use of computerized steady-state process design balance systems has reduced engineering man-hours by as much as 80 to 1 over conventional manual balance calculations. The popularity and widespread use of such systems by the minerals industry increased dramatically in recent years, but these systems were mainly available for use on large main frame computers and lacked graphic capability. A considerable amount of engineering manpower was required to "conceptualize" a process flowsheet. After sketching the flowsheet layout, the engineer was still faced in most cases with a time-consuming reduction of his graphic concept of the problem to numerical data required by the balance program. Furthermore, output from these early systems was usually in tabular numeric form. The computer results then were transferred manually to a pictorial representation of the process. A new process design balance system has been developed which runs on a popular and inexpensive personal computer. This system combines modern Computer Aided Design (CAD) principles and the graphics capabilities of the personal computer to allow the process engineer to define a flowsheet problem while creating a process flow diagram. The system provides balance results in both pictorial and tabular form. Past, present, and potential applications of the system are discussed, and an analysis of the cost benefits derived from its use are provided.

Jan 1, 1985

By K. V. S. Sastry, A. J. Hunt, K. D. Lofftus

Sol-gel processing is rapidly becoming an important process for producing such advanced materials as high activity catalysts, fiber optics and ceramic precursors. These materials can be tailor made with properties unique to sol particles as well as the gel aggregates by controlling production of the sol, the formation of the gel, and the removal of the interstitial fluids. This paper presents colloidal and kinetic principles of sol generation and gel formation. Hydrolysis of alkoxides provides the best means of controlling sol production and electrostatic stabilization enables the formation of the most homogeneous gels. Gelation occurs by hierarchial aggregation which produces inhomogeneities much larger than the sol particles. Colloidal and kinetic principles can be applied to reduce the size of the inhomogeneities and obtain high performance transparent insulation and new ceramic composites.

Jan 1, 1990

By Harold A. Taylor

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 AD graphite crucibles were being made in the Haffnerzell District of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still being used for the mineral are plumbago, meaning lead-silver, and black lead. The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it graphite from the Greek word graphein, meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Sri Lankan graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite.

Jan 1, 1994

By J. C. Weimer

The goal of Bethlehem's mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By Philip G. Meikle

The Bureau of Mines Coal Mining Technology program has developed new concepts aimed at improving the efficiency of underground coal product ion. Conceptual designs have resulted in equipment prototypes, some of which are currently undergoing proof-of-concept evaluations at Bureau and cooperator facilities. Several of these systems and concepts are described.

Jan 1, 1984

By George Bárdossy

Most of the bauxite deposits in Europe belong to the karst type. They are located mainly ill Southern Europe along the Mediterranean Sea and in the Ural Mountains. Lateritic bauxite deposits occur on the Russian Platform, in Poland, Northern Ireland and in Turkey. Tikhvin-type deposits arc found on the Russian Platform. Bauxite formation in Europe started in the Middle Devonian. The main bauxite forming period was the Upper Cretaceous. Very few bauxites are younger than Eocene. Most deposits are covered by overburden of up to 1000 m. Prospecting is carried out by drilling. Several geophysical methods are used to detect the hidden deposits. Geostatistical methods were introduced in several countries for evaluation of the reserves and the geometry of the deposits. Data on bauxite production are given for 1982 and since the beginning of mining in Europe.

Jan 1, 1984

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By T. G. Hayes

Economic and environmental regulations in the coal industry have required companies to evaluate their current blasting method of loosening in-situ coal. This paper will review ripping vs. blasting thick in-situ coal seams, handling frozen active coal stockpiles and proper stockpile conditioning and reclaiming. How basic operating technique can improve job efficiency, productivity and cost per ton.

Jan 1, 1995

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have been made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modeling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developed that can be calibrated for ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables prediction of the complete composite particle distribution and thus is valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1988

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018