Search Documents

By Mauricio Brücher, Juan Camus

This article deals with open pit mine planning and a computer technology known as Direct Block Scheduling, or “DBS”. This is an emerging technology for modeling mine exploitation strategies using mixed-integer linear programming. This technique has proved to yield stronger economic results compared to the Lerchs-Grossmann (“LG”) algorithm currently used at the beginning of the mine planning process. The article briefly describes the shortcomings of current practice; then, this delves into the superior results obtained by DBS technology compared to current practice. Finally, the article argues that results achieve so far by DBS could be enhanced even further. To do this, the framework to apply this emerging technology, which is also used in current practice, should be modified to better exploit the capabilities of DBS technology. To better understand this change, an illustrated case study is presented at the end of the article.

Jun 25, 2023

By C. Zhou, C. C. Jobes, J. H. DuCarme

"Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM—the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered. INTRODUCTION Continuous mining machines (CMMs) can be up to 10 m (33’) in length and more than 3 m (10’) in width. These machines perform the coal cutting operations in underground room-and-pillar coal mines. Accidents during CMM operation accounts for an average of 250 injuries every year, and 43 miners have been killed by striking or pinning accidents involving CMMs in the United States from 1984 to 2015.Because of these fatalities and injuries, the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 that requires the use of proximity detection systems (PDSs) on all CMMs with the exception of full-face machines (Mine Safety and Health Administration, 2015). Currently, there are five different proximity detection systems that MSHA has approved as permissible for use in U.S. underground coal mines (Mine Safety and Health Administration, 2013). All of these PDSs rely on a miner-wearable component (MWC) to detect the generated magnetic fields that PDSs produce around a CMM (Schiffbauer, 2002). These systems use the magnetic field strength readings in terms of magnetic flux density from the MWC to determine whether a miner is at a safe distance from the CMM. A stable magnetic field is essential for the accuracy of a PDS."

Jan 1, 2018

Iron ores may be upgraded by flotation of iron oxides or siliceous gangue using either cationic or anionic collectors. The electrostatic mechanism of adsorption can account for the complex chemistry involved. In industrial practice, only cationic silica flotation is used at present in North America. Some of the seemingly paradoxical phenomena of cationic silica flotation behaviors in meeting the demand for low silica concentrates are reviewed.

Jan 1, 1989

By Robert C. Bates

Background is given on the various equations used to describe diffusion and convective flow of radon in porous media. Bureau-developed equations for modeling diffusion and Darcy flow through multilayered porous media are described briefly, and examples of their use are given. Analysis results discussed include: The transient effect of pressure changes in different length models, time dependent flux changes in multi-layered models, and radon flux through pinholes in sealants

Jan 1, 1980

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By John F. Schat, T. William Thompson

Laboratory data on the time-dependent compaction of porous rocks are presented, and various attempts to model this behavior are described. These lead to a discussion of the problems that arise in using laboratory data to estimate long-term effects. A method is suggested for combining laboratory data with information from the geologic record to estimate long term effects.

Jan 1, 1986

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth's surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By J. Brent Hiskey

INTRODUCTION Metal electrodeposition processes are of fundamental technological importance to a number of fields. Electrorefining, electrowinning, electroplating, and electrogalvanizing have all been the subject of intense study for over a century. More recently, electrochem- ical deposition has played a critical role in advances in microelectronics and lately has been an enabling technology for the production of certain nanostructured materials. Electrometallurgists have most frequently been concerned with the structure and morphology of massive deposits. For example, in metal recovery steps such as electrorefining and electrowinning, deposits demonstrating adherent coarse-grained characteristics are most desirable. In the case of electroplating, a bright fine-grained, tenacious and strongly adherent deposit is required. The fabrication of microelectronic devices and the production of nanoscale structures such as nanoparticles, nanowires, and nanorods requires a keen understanding of early stage deposition effects. The initial stages of metal deposition, usually referred to as electroclystallization, are fundamentally linked to nucleation and growth phenomena. Early stage deposits are typically very ordered. Whereas, bulk metal deposition structures are much more ran- dom. In both cases, the discharge of a metal ion at an electrified interface is represented by simple cathodic reduction as follows: [ ] Me(H2O)xn[ ] is a hydrated metal ion residing in the bulk solution and Me is the metal atom occupying a crystallographic lattice position. A similar reduction reaction can be

Jan 1, 2005

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By C. Konya, A. Konya

"INTRODUCTION Over the past twenty years this Linear-Regression Modeling has become widely accepted for ensuring limits are not exceeded at a site, using the Scaled-Distance variable. In today’s industry, numerous equations are present for different scenarios, geologic environments, hole sizes, and numerous other factors with an emphasis on site-specific equations developed for all major projects; however, underground blasting applications have not been analyzed to a great degree of detail. Without previous knowledge this puts underground blasting operations into a guessing-game to ensure that vibration levels are not exceeded. This paper will review two recent projects that have been worked on by the authors and linear-regression models that were used with both burn cuts and stope blasts. BLAST VIBRATIONS MODELING The first major research project conducted in the United States on blasting vibration was Bulletin 442 (Thoenen & Windes, 1942) which looked at the relationship between blasting and blast vibrations in the fall of 1940. This study examined numerous blasts and began the investigation into topics such as damping, structural damage from vibrations, frequency dependency on vibration, resonance vibration, delayed blasting, and numerous other factors. Bulletin 442 had two major conclusions which are: 1. The vibration from a blast can be predicted with a relationship of size of the shot and distance to the structure (now known as scaled distance) 2. “The vibration of a structure at resonance does not in itself cause damage because of the restraining effect of damping inherent in the building” (Thoenen & Windes, 1942) Due to the increase of blasting near homes and busier areas the USBM commissioned an additional study to further develop a few of the topics covered in Bulletin 442; this study would go on to be published as RI 6561 (Duvall, Johnson, Meyer, & Devine, 1963) with the study looking into delayed blasting and the relationship between charge weight, distance, and peak particle velocity of the blast. This relationship would be termed as the ‘scaled-distance’ and take the form of:"

Jan 1, 2018

By Jim Salley, Mohammad Saleem, Indra Banerjee, Kevin Sapp

"On underground construction projects, effective Quality Management is essential for ensuring facility durability, life cycle performance and low maintainability. Furthermore, follow on contracts also rely on an effective quality management system for interface congruency. An effective Quality Management System (QMS) is also essential in mitigating risks and meeting schedule and budget performance objectives. For the past 15 years Central Puget Sound Regional Transit Authority’s Link Light Rail extension has successfully completed over 10 miles of twin bore tunneling and associated underground features including cross passages, deep sump structures and shafts. After the completion of each segment, lessons learned have successfully been implemented to improve the quality of delivered projects. This paper presents the Sound Transit QMS with regard to a number of project elements of tunnel construction projects, with specific focus on quality performance of slurry wall construction, TBM tunnel excavation assessment, segment production and segmental lining installation, and other associated construction features. A collaborated total QMS will be presented in this paper that will serve as a guide for successful implementation of Quality Assurance and Quality Control processes. INTRODUCTION Implementation of a robust Quality Management System reduces defects, errors and omissions, identifies and addresses nonconformance in a timely manner and increases stakeholder confidence in the project. In fact and effective QMS helps ensure that optimal project outcomes are realized both in terms of project delivery and life cycle performance. The two key components of QMS are quality control and quality assurance. Quality Control (QC) is the procedure implemented to achieve a certain level of quality and ensure that products, processes and services meet specific requirements. Quality Assurance (QA) activities are carried out to evaluate the effectiveness of the quality control measures and ensure that the QC process is working. A team obligation that recognizes that quality is built into every aspect of a project is the basic concept of a successful QMS."

Jan 1, 2016

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state's population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By C. Tsatsanifos

Following closure of an old asbestos mine in Zidani, Kozani Prefecture, Greece, the geotechnical and environmental restoration of the tailings slopes was required. The geotechnical aspects of the restoration included the formation of gentler slopes to increase stability, in combination with drainage works for the same purpose. The environmental aspects of the restoration included covering the slopes with successive layers of soil in order to minimize infiltration of rainwater, and hence the potential for further transport of asbestos fibers, and to provide a suitable layer for revegetation of the slope. The paper presents results of slope stability evaluation using both limit equilibrium and finite element analyses and raises some issues related to reducing impacts to the geoenvironment when designing such restoration projects.

Jan 1, 2006

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993