Search Documents

By Tim Q. Haldane

The ability to efficiently process low grade gold ores has allowed the Gold Fields Mesquite Mine in Imperial County, California to expand from a 2.1 million tonne per year rate in 1986 to its present 7.3 million tonne per year processing rate. Increased tonnage demands led to the 1989 construction and start-up of a dump leach pad to supplement the existing heap leach operation, resulting in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. An overview of current operating practices at Mesquite is presented along with metallurgical and economic comparisons between the crushed and run-of-mine ore heaps.

Jan 1, 1990

By J. -C. Roegiers, M. Thiercelin

Accurate toughness determinations are difficult to achieve in the case of soft or heterogeneous rocks. The existence of a large process zone ahead of the crack tip makes the determination of the apparent toughness crack length dependent, in the case of subsized specimens. In order to use practical size specimens, the authors propose a new toughness test, the Modified Ring Test, which pre- vents a largely developed process zone to form ahead of the crack tip. This test has also the advantage that its geometry is core-based. Numerical and experimental results are discussed.

Jan 1, 1986

By J. B. Nanor, J. Lorengo, M. Misra, C. B. Bucknam

The dissolution of mercury during the gold cyanidation process is the cause of many environmental, health and processing problems. The removal of mercury-cyanide complexes from synthetic solutions and process water were investigated using sodium and potassium dimethyl dithiocarhamates and sodium sulfide as precipitating reagents. The results have shown that efficient mercury removal can he achieved by the formation of stable mercury compounds with the addition of potassium dimethyl dithioearhamate. The mercury dimethyl dithioearhamate precipitates are stable under plant operating conditions, and they do not have any deleterious effect on gold adsorption by activated carbon. Furthermore, it is possible to stabilize mercury in the heap during cyanidation by adding dimethyl dithioearhomate.

Jan 1, 1999

This paper discusses how the link between design software tools and recycling models can be established in order to predict the recyclability of the car during the design phase, as well as to be able to apply design for recycling on a solid technological basis. Due to the complexity of the design of the car, optimisation of recycling can only be realised based on a sound technological basis, in which the dynamic and statistically distributed parameters affecting the recycling rate are described and understood. This paper gives a brief overview of the dynamic and recycling models, which are developed for optimisation of the recycling of the car and the calculation of recycling rates of the car in the design phase in view of EU legislation. Moreover the possibilities for modelling of shredding and liberation within the recycling system are discussed. The performance of experiments on a fundamental basis in order to collect statistically correct industrial data, supported by a closing mass balance, is referred to on the basis of a large scale industrial recycling experiment. It will be shown how design for recycling and environment can be supported by the sophisticated models as developed by the authors.

Jan 1, 2005

By David L. Bradfield

This paper covers the development of the Yeelirrie Uranium Project from the discovery of the Yeelirrie deposit in 1970 to the present time, with emphasis on the mining, processing, and environmental requirements of the project. The Yeelirrie Uranium Project is managed by the "Yeelirrie Uranium Joint Venture Partnership", which, when formed, consisted of Yeelirrie Development Company Pty., Ltd., Urangesellschaft, Australia Pty. Ltd. and Esso Exploration and Production Australia Inc. The Yeelirrie Uranium Joint Venture Partnership holds mineral claims over the Yeelirrie uranium ore deposit in Western Australia. This deposit encompasses some 35 million tonnes of ore containing in excess of 50,000 tonnes of uranium as U308. Agreement has been reached with the State of Western Australia to mine and process the ore to produce uranium ore concentrate. The Project scope provides for an open-cut mine, alkaline leach hydrometallurgy plant, power plant, township, airstrip, access roads, community services and utilities. The Yeelirrie Uranium Project described herein has progressed through the stages of exploration, mine evaluation, process testing, project scope definition, environmental approval, Pilot Plant operation, preliminary engineering and the publishing of a definitive Project Feasibility Study. This article summarizes the project development through the above stages.

Jan 1, 1984

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By James C. Burrows, Frances Kramer Mesher

Tungsten-containing ores are mined on all continents of the world. China is the world's largest producer and controls the world's largest reserves. The USSR, itself a sizeable producer, is estimated to be the world's largest consumer. The major use for tungsten in the noncommunist world is in production of cemented tungsten carbides for cutting, drilling, and wear parts. Other major uses include lamp wires, steels for tools, and armaments. Real tungsten prices have been in a general decline since 1977-1979 as the tungsten market undergoes basic and lasting structural changes.

Jan 1, 1986

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

By M. Z. Rashad, H. A. El-Sageer

The intersections of numerous joint sets at the surface of tunnels of the Abu-Tartour project in Egypt create blocks of irregular shape and size in the rock mass. Although most of these blocks are unable to move into the free space of the tunnel, a few key blocks are capable of such movement. In addition, as soon as they move, some restrained blocks will be liberated. The aim of this work is to find the removable key blocks of the walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks and then determine the best tunnel direction.

Jan 1, 1993

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By Michael Schultz, Gregory Sanders

The City of New Haven is proposing to construct Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 200 cubic feet per second (cfs) stormwater pump station; and a 914 meter (3,000 linear feet) long tunnel segment with an internal diameter of 2.1 meters (84-inches). The tunnel alignment will cross under the Long Warf railyard and then continue parallel to the Vison Trail Route. This paper presents the local geology and subsurface conditions, as well as discusses the major project challenges and risks including construction in soft marine soils and encountering remnants of the former wharf.

Jun 13, 2021

By Thomas P. Meloy

The understanding, quantification and use of locked particles. Specifically discussed is the use of Textural Transforms (Meloy, 1991) for the implementation of the Interfacial Area Conservation hypothesis (Meloy, 1984); the quantification of the locked particles as a function of fragment to inclusion size ratio; and the selection of set points.

Jan 1, 1991

By Frank T. Wheby, Edward M. Cikanek

A computer performs all logic and computations customarily done by hand in preparation of engineers' estimates or contractors' bids on tunnel-shaft systems. The program described is based on construction methods, work forces and equipment selections corresponding to the current state-of-the-art of rock, soft ground and cut-and-cover tunneling. The program contains logic to permit estimates of cost of complicated tunnel-shaft systems; it is not necessary to input quantities, as the program calculates those from the tunnel design that is internally generated. In any estimate, the program bases its cost computation on user-input requirements and site conditions, such as tunnel shape and size, shaft depth, ground characteristics, construction methods, and other factors. To provide great flexibility, the user of the program is provided with options for accepting designs built into the program or overriding these designs by his own inputs. An illustrative example is presented.

Jan 1, 1974

By H. M. Breza

Utilization of Bucket Wheel Excavators and Overland Conveyor Systems to remove overburden provides increased productivity and flexibility to a surface mining operation. The utilization of such a system at the Texasgulf Inc. Aurora, North Carolina Mine has significantly improved the overall productivity of the mining operation. System flexibility is evidenced by adaptation to operation requirements such as mining area moves, movement of excavated overburden to designated sites, selective handling of overburden, spoil placement contouring, and providing an environmentally sound and safe operation. System productivity is evidenced by actual case studies relating to overall production, excavation rates, and cost effectiveness.

Jan 1, 1993

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

By Joel K. Witt, Jackson G. Jenkins, Wendy M. Gort, Brent A. Whitman

A major concern for operators of leaching/SX-EW plants is a phenomenon known as gunk or crud. The build up of gunk is typically the result of fine particulates which are transported via the leach operation to the solvent extraction plant. The particulates develop into a solid layer that concentrates at the aqueous/organic interface. This can cause phase separation problems which can result in entrainment and other deleterious operating conditions. Most operations physically remove the gunk from the SX settlers and process it via a centrifuge or coalescer to remove valuable organic. While both methods have served for many years, Magma is currently evaluating the use of a chemical surfactant which induces a definitive separation of particulates from organic.

Jan 1, 1994

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By S. K. Kawatra, S. Bagley, T. C. Eisele

To meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1988

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993