Search Documents

By P. M. Sandgren, H. Al-Dabbagh

Saudi Company for Precious Metals (SCPM) is jointly owned by the Saudi Arabian state organization Petromin (The General Petroleium & Mineral Organization) and Boliden of Sweden. The company operates the Sukhaybarat gold mine in the Saudi Arabian desert and produces some 80,000 ounces of gold per year by agitation and heap leaching. The discovery, development, and operation of this mine is a success story. After the first drill hole intercepted a gold mineralization in 1983, it took the partners only 8 years to delineate the ore reserve, locate water sources, prepare pre-and final feasibility studies, obtain permits, design, and construct the facilities. Sukhaybarat, which is an open pit mine, started off with a carbon-in-leach agitation plant only, but a heap leach facility was added in the beginning of 1995. Since start of operation in the middle of 1991, a total of 300,000 ounces of gold has been produced in the first four years of operation at a very competitive cost.

Jan 1, 1996

By Louis W. Cope

The various types of placer deposits will be described as an introduction to the subject. The several methods and machines used for sample taking and processing will be discussed. The advantages and disadvantages of each will be covered. Included will be mistakes and pitfalls of placer sampling and sample reduction.

Jan 1, 1987

By John T. Crawford

Various open pit limit-analysis techniques have been utilized for many years to design pit limit surfaces. In the last 15 years there have been many advances in developing sophisticated computer methods to aid this process. The extensive capability of the digital computer has led to effective utilization of multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long range and intermediate range mine planning and design needs. This paper provides an overview of some of the more important of these applications. While not covered in detail, they are meant to indicate the flexibility and adaptability of open pit limit analysis methods and to stimulate thought.

Jan 1, 1979

By Alan C. Noble

Ore reserves are often less than 30% of geologic resource estimates that are initially prepared by exploration geologists. Differences of this magnitude between resources and reserves can lead to serious . problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves and are later found to be misleading and gross overstatements of ore reserves. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery, and economics early in the project and by using appropriate qualifiers in the resource statement Examples using typical deposit characteristics are used to demonstrate how cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1992

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By Kenneth N. Han, Yuhong Chen

The removal of carbonaceous material from Carlin gold ore has been investigated via froth flotation. The effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material has been studied. Other variables affecting froth flotation efficiency were also examined closely. These included particle size, pH of the solution, and temperature. The effect of reduction and oxidation of carbonaceous material on froth flotation efficiency has also been investigated. This investigation showed that aromatic type oil was the most effective collector. Also found in this investigation was that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation. More than fifty percent of the carbonaceous material was able to be removed via froth flotation. It can be concluded from this study that the effect of pH and temperature during the rougher flotation state is of little significance to the overall recovery of carbonaceous material. Since pyrite is responsible for the high consumption of chlorine, removal of pyrite is very important in order to reduce the overall consumption of chlorine.

Jan 1, 1990

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By C. J. Pritchard

Productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity. So a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The low-productivity, tailgate-development, continuous-miner section has been transformed into to a high-productivity, development-retreat section that is also available for long-term mine development duties, increasing mine planning flexibility.

Jan 1, 1991

By F. F. Aplan, S. Chander, A. R. Alaboyun

Several aspects of the capture of hydrophobic dust particles by droplets in sprays have been studied. The particle capture depends on several sub-processes involving collision, adhesion and engulfment. The collision events between dust particles and a single droplet were observed with a high speed motion analysis system to determine the influence of a surfactant on the capture process. In the adhesive process it was observed that the dust particles are collected at the surface of the water droplet to produce a rigid film at high dust loadings. In the presence of the surfactant, however, the particles were engulfed inside the droplet keeping a fresh surface on the droplet available for capture of more particles. A theoretical analysis is presented to take into account the role of contact angle on the penetration of particles into droplets. A significant increase in collection efficiency was observed with decrease in droplet size.

Jan 1, 1991

By C. P. Mangelsdorf

Introduction During the 13 years since C. C. White introduced the Birmingham roof truss there has been a revolution in permanent roof support technology. While not all of the emerging concepts have their origins in the truss-resin bolting is a prime example - the combinations and permutations of devices presently available to the underground mining industry reflect a well-spring of creative activity. The purpose of this report is to chronicle a number of roof support system that have same physical similarity to the Birmingham truss, and to report on their application. Definitions The application of the tern "truss" to the device developed by White of the Birmingham Bolt Company in 1967 may be derived from the classical technique of stifwood, by the attachment of an underslung, sometimes pretensioned metal strap, rod or cable. If the beam is separated from the reinforcement by a single block or vertical post it is called a "King's Post Truss". If two equally spaced blocks or posts are used it is referred to as "Queen's Post". When the immediate roof of a mine is visualized as a beam, the Birmingham device completes a structure resembling this latter form.

Jan 1, 1982

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By T. D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

Jan 1, 2012

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By G. A. Rowell, T. M. Barczak, J. C. Zelanko

The US Bureau of Mines conducted a multifaceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps because the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements and microseismic monitoring, as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading and microseismic activity were monitored prior to, during and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and following the face bump. Shield load data, evaluated in an effort to identify trends that could be used to forecast coal bumps, appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source-location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1992

By Gerald H. Luttrell, Rick Q. Honaker

A coal preparation plant incorporates a variety of solid-solid separation processes that operate in relatively independent parallel circuits. Studies have shown that total plant performance can be optimized by selecting circuit cutpoints that maximize total clean coal yield irrespective of the performance of individual circuits. Although the optimum cutpoints can be determined using simulation programs, these mathematical routines require detailed washability data and empirical partition information that is not often available to plant operators. In addition, routine fluctuations in the washability characteristics of the plant feed make this approach impractical to implement in industrial facilities. As an alternative, practical optimization criteria can be developed for plant operators through a fundamental understanding of scientific principles involved in coal cleaning operations. This article provides an overview of the most important optimization criteria and presents several industrial case studies that illustrate the financial benefits of this practical approach m plant optimization.

Jan 1, 2005

By R. N. Chakravorty, R. J. Kolada

Explosions of methane in coal silos and coal ships is an ever present hazard. Recent investigations have shown beyond question that considerable accumulations of methane do occur in coal storage silos and numerous recent explosions in coal transport shipping strongly indicates that the same conditions also exist in ship storage holds. Investigations have shown that the main concentrations of methane occur within the actual coal pile. Within this region normal silo and ship ventilation systems are ineffective. The main 1ine of defence is therefore to exclude potential sources of ignition or to place the coal in an inert atmosphere, or both. This paper presents the results of a methane survey of all operating silos in Western Canada. These results demonstrate that a serious and widespread hazard of explosion exists. This paper also discusses various methods by which this hazard may be reduced including methods of venti1ation, inertization, microbiological control and early warning systems.

Jan 1, 1987

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980