Search Documents

By G. Banini

A plug-flow model is described for the reactor mass balance of a typical AARL gold elution process. The model is in the form of a hyperbolic differential equation and was transformed using the method of characteristics. The transformed model was then solved simultaneously with models dependent on intraparticle surface diffusion and film transfer parameters. The solution was found to represent the experimental data for a modified form of the AARL elution. Correlation between the experimental conditions and the film transfer parameters estimated by the model are also presented.

Jan 1, 1998

By Louis A. Sandbak

Drift excavation by boom-type roadheaders in the San Manuel and Kalamazoo sulfide copper ore bodies has been successfully demonstrated. Geomechanical rock classification in conjunction with detailed geologic mapping has been necessary to assess roadheader performance, and to predict advance rates in the varied rock classes in the San Manuel block caving mine. Rapid excavation and less fractured ground are obvious advantages of roadheader drift excavation over conventional drill and blast techniques. The geomechanical system of Engineers International (1984) can be an effective roadheader performance and ground support tool.

Jan 1, 1985

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By S. S. Peng, V. Z. Sun

One of the major concerns of ground control in a coal mine is the prevention of roof, pillar and floor failures of the mine entry. To better design and evaluate the stability of a mine entry within a certain level of confidence, a reliability approach is introduced. The advantage of using the reliability approach, rather than the conventional safety-factor (SF) method, is that it not only takes variability of both rock/coal properties and stress into consideration but also assesses the stability of each component and the mine entry as a whole. Therefore, it is anticipated that by using this approach the current ground-control technology in a coal mine will convey a better sense of confidence. The results of a case study show that there is a significant difference in mine entry stability between the current design method and the reliability approach.

Jan 1, 1999

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By Robert A. Robinson, Steven R. Thompson, Harvey W. Parker

The Mt. Baker Ridge Tunnel, under construction in Seattle, will be the world's largest-diameter soil tunnel with an inside diameter of 19.2 m (63 ft) and an effective outside diameter of about 24.4 m (80 ft). The five-lane highway tunnel will be constructed using a "stacked-drift" scheme in which an articulated or "flexible" tunnel lining consisting of 24 concrete-filled drifts is constructed to form a horizontal compression ring followed by removal of the soil core. Geotechnical factors, including variable strength hard fissured soils, high horizontal stresses, potentially unstable sands, and prior slope instabilities, significantly influenced the innovative design and construction approach.

Jan 1, 1983

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Aquifer. A formation, group of formations, or part of a formation that contains sufficient satu rated permeable material to yield significant quan tities of water to wells and springs. Artesian. Synonymous with confined; see ground water, confined. Capillary fringe. The zone immediately above the water table in which all or some of the interstices are filled with water that is under less than atmospheric pressure and that is continuous with the water below the water table. Conceptual model. A conceptualization of a field hydrogeologic framework that facilitates the development of analytical field testing procedures. The results of the test(s) may force changes in the initial conceptual model. Conductivity, hydraulic. Replaces the term "field coefficient of permeability." The volume of water at the existing kinematic viscosity that will move in unit time under a unit hydraulic gradient through a unit area measured at right angles to the direction of flow, if the porous medium is isotropic and the fluid homogeneous. Confining bed. A body of "impermeable" material stratigraphically adjacent to one or more aquifers; its hydraulic conductivity may range from nearly zero to some value distinctly lower than that of the aquifer. Flow, steady. Any point where the magnitude and direction of the specific discharge are constant in time. Flow, uniform. At every point the specific discharge has the same magnitude and direction. Flow, unsteady. At any point the magnitude or direction of the specific discharge changes with time. Fluid potential. The mechanical energy per unit mass of a fluid at any given point in space and time with respect to an arbitrary state and datum; the fluid potential is proportional to the head. Ground water, confined. Ground water under pressure significantly greater than atmospheric; its upper limit is the bottom of a bed of distinctly lower hydraulic conductivity than that of the material in which the confined water occurs. Ground water, perched. Unconfined ground water separated from an underlying body of ground water by an unsaturated zone. Ground water, unconfined. Water in an aquifer that has a water table. Head, static. Height above a standard datum of the surface of a column of water (or other liquid) that can be supported by the static pressure at a given point. Homogeneity. Hydrogeologic properties are identical everywhere. Hydraulic gradient. Change in static head per unit of distance in a given direction. Hydrostratigraphic unit. A body of material having considerable lateral extent and comprising a geologic framework for a reasonably distinct hydrogeologic system. Isotropy. Condition in which all significant properties are independent of direction. Porosity. Property of containing interstices or voids; may be expressed quantitatively as the ratio of the volume of its interstices to its total volume. Porosity, effective. Interconnected pore space available for fluid transmission; expressed as a percentage of the total volume occupied by the interconnecting interstices. Potentiometric surface. A surface that represents the static head along a particular specified surface or stratum. Specific retention. Ratio of the volume of water that the rock or soil, after being saturated, will retain against the pull of gravity to the volume of the rock or soil. Specific yield. Ratio of the volume of water that the rock or soil, after being saturated, will yield by gravity to the volume of the rock or soil. Storage, specific. The volume of water released from or taken into storage per unit volume of the porous medium per unit change in head.

Jan 1, 1986

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986

By G. W. Luxbacher

Acid rain legislation included in the Clean Air Act Amendments of 1990 caused a great deal of uncertainty regarding the price, source and production quantities of coal supplied to the eastern coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward. South American coals move into the northern markets. States are proposing legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries. Some utilities question the long-term availability of eastern compliance coal. Major coal producers must make decisions now to assure their continuing presence in the market place. Several companies have adopted a strategy to acquire eastern compliance reserves, while others have invested in technology to compete as a low-cost producer. Legislation "Acid rain." This is a topic that was debated within the scientific, environmental and industrial communities for years. Those discussions resulted in a large outlay for the federal National Acid Precipitation Assessment Project (NAPAP), which was then ignored. Acid rain then became the subject of a "60 Minutes" broadcast that debunked the acid rain theory, supporting the NAPAP study conclusions. In the final outcome, however, acid rain was the driver for the Clean Air Act Amendments of 1990.

Jan 1, 1992

By R. B. Coleman, T. P. McNulty

HISTORICAL PERSPECTIVE Environmental protection is not a newcomer to the minerals industry, there having been numerous examples dating from decades ago. Sometimes the awareness of a need for preservation or restoration derived from the ethics and principles of the engineers and management responsible for development and operation of a property. On the other hand, pressures to clean up industrial messes frequently were applied by special interests such as farming and ranching, recreational and conservational groups, and local governing bodies. Mineral industry environmental controls in this century have therefore been a patchwork of good intentions and bad, clean operations and dirty ones. The Hoboken siphon converter for converting copper matte while effectively capturing sulfur dioxide at a relatively high concentration was developed in Olen, Belgium in 1928, a full sixty years ago. The alternative was closure of the Hoboken smelter by Belgian government health officials who had become intolerant of sulfur dioxide emissions which were causing serious respiratory ailments in the river valley in which Olen is situated. As early as 1958, the Anaconda Company had a full-time botanist on its metallurgical research staff with the responsibility of learning how to vegetate the extensive tailings deposits at Anaconda, Montana. By that time, considerable progress had already been made in restoration of Silver Bow Creek, which at one time was “dead” for as far as 40 miles down- stream from the point of entry of acid mine drainage in Butte.

Jan 1, 1989

By R. L. Grayson

The Office for Mine Safety and Health Research, National Institute for Occupational Safety and Health is responsible for providing research leadership in the prevention of mining work-related illness, injury and death. Planning of the NIOSH FY99 research program focused on the comprehensive collection and risk analysis of fatality, injury and illness data according to commodity and mine type. This data, coupled with the mapping of information obtained from stakeholder meetings over several years, provided the basis for prioritizing research needs. Results of the combined analysis were compared to the FY98 program to identify surveillance and research gap areas. The FY98 research program was then assessed according to commodity and mine type and compared with exposure assessments, traumatic fatality rates, injury rates and employment trends in each commodity-mine type combination to gain insight into the potential balance of the future research program. This paper presents the methods, data and results of this planning process.

Jan 1, 2002

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Francis S. Kendorski

INTRODUCTION Drift design problems in caving operations are a re¬sult of the geologic factors contributing to the overall success of the system, of the engineering factors dictated by economic and technical considerations, and of ore production practices. Combining these factors, a rational underground sup¬port system of rock reinforcement, light steel channel section or welded wire fabric, and shotcrete can be de¬signed based on rock fracturing, rock load, abutment loadings, ground movement, expected repair and desired flexibility. The design concept uses the effect achieved by restraining, reinforcing, and maintaining some of the intrinsic strength of the fractured rock mass composed of interlocked blocks of intact rock and rock fractures. Three different examples of drift support design in hypo¬thetical mines using the caving system are given. Caving is a system of underground mining where ore is extracted by means of gravity after the ore body is allowed to fail by removing support from underneath. The rock mass of the ore body fractures and flows ver¬tically downward to let gravity do as much work as pos¬sible. Caving differs from many other mining systems in that blasting is used only to initiate the rock mass failure by removing the rock supporting the ore but not to break the ore itself. The initial movement of the rock mass dur¬ing failure and the consequent crushing and grinding during the continued movement serve to reduce the ore to particles of a manageable size, with only limited sec¬ondary blasting necessary. The broken ore is extracted from the bottom of the failed rock mass through funnels of some sort pre-excavated in the rock. Ore extraction must continue or the swell of the broken rock will even¬tually fill the cavity and stop further rock mass failure and movement. The excellent general discussion on block caving in the SME Mining Engineering Handbook (Julin and Tobie, 1973) adequately covers the principles and application of this type of underground mining. Many rock mechanics aspects of block caving have been covered by others (McMahon and Kendrick, 1969; Swaisgood, et al., 1972; Mahtab and Dixon, 1975; King, 1946) and will not be reviewed further. Maintaining the stability of production drifts is one of the most troublesome problems plaguing the mine manager in a caving operation. Many factors contrib¬ute to drift support problems, and identifying the causes of instability and producing a reasonable support design are two steps toward achieving stability consistent with the mine plan. This chapter sets forth a technique for the design of support systems for production drifts in caving opera¬tions. The basic support system elements employed are rock reinforcement, welded wire fabric, and shotcrete. Recognized as contributing to the design are the factors of rock load, additional load from mining activity, rock fracture characteristics, repair expected, and flexibility. It must be emphasized that the drift must first be stabilized as for a tunnel, and the additional strengthen¬ing for mining-induced loads cannot contribute to the initial premining stabilization, or the reserve of strength is used up. MINE PLANNING The efficient mine planning engineer not only must satisfy the economic, human, and environmental aspects of his task but must also consider the mechanical con¬sequences of his plan. The problems created for the mine by placing parallel drifts too close, by crossing drifts on different levels with inadequate, if any, separa¬tion, and by installing connections and crossovers in the haulage plan without regard for the effective spans cre¬ated, are only a few of the problems a mine planning engineer can create for himself and the mine. The effect on immediately adjacent mine areas when an area is caved is important to drift design because the removal of vertical support from a rock mass causes the weight of that rock mass to be shifted elsewhere. The adjacent rock mass will carry this load and reach a new equilibrium with the applied stress. The advancing front of stress increase that results from caving (and many other mining systems) is generally called the abutment load and is the increase in stress over the gravity or tec¬tonic stress that already exists, as shown in Fig. 1. In general, the abutment load will be similar in nature to the stress change found around an opening in rock and will be taken as causing an increase in the vertical prin¬cipal stress, due to an approaching caving boundary, so that

Jan 1, 1982

By Wang Dianzuo, Luo Lin, Hu Yuehua, Qiu Guanzhou

This paper introduces a novel classification approach named the flotation classification approach which works by controlling interactions between particles. It differs considerably from the conventional classification processes operating on mechanical forces. In the present test, the micro-bubble flotation technology is grafted onto hydro-classification. Selective aggregation and dispersion of ultrafine particles are achieved through governing the interactions in the classification process. A series of laboratory classification tests for -44 pm kaolin have been conducted on a classification column. As a result, about 92 percent recovery for minus 2 pm size fraction Kaolin in the final product is obtained. In addition, two criteria for the classification are set up. Finally, a principle of classifying and controlling the interactions between particles is discussed in terms of surface thermodynamics and hydrodynamics.

Jan 1, 1995

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistent properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables that should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operation's survival in the competitive mineral industry.

Jan 1, 1990

By W. A. Niepelt, F. A. Locher

Flow in steep cascades may lead to the occurrence of a nearly periodic train of waves known as slug flow. This, in turn, may result in overtopping of the channel walls and problems with energy dissipation in receiving sumps. Experimental data from an operating facility was used to extend clear water technology for predicting the occurrence of slug flow to conditions with slurry flows. A design methodology and a design chart to determine the region of steady flows is presented that will permit the design engineer to avoid slug flow in cascade systems for conveyance of slurries.

Jan 1, 1990

By Sriram Padmanabhan, Jan M. Mutmansky

The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Utah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7. The results will be presented using two categories of data collected during two separate phases of the research: (1) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and (2) quartz concentration data from mines chosen at random. The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent.

Jan 1, 1989

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By R. V. Ramani, S. Tan

A computer-oriented systems simulator (CMHS) has been developed for analysis of continuous materials handling systems. Special emphasis has been placed in the model on several features that are unique to these systems. These features include periodic pattern of material arrival from several sources, several types of material to he transferred, material dispatch processes, intermediate storage capacities, and multiple material destinations. Both the deterministic factors of the continuous material handling system, such as the physical decomposition of the system and the scheme and schedule of its operation, and the stochastic factors, such as variations of material arrival, material pattern on the conveyor, and availabilities of the system elements, are considered in the simulator. The application, of the model is demonstrated through a study of an underground conveyor belt network serving long- wall and continuous miner sections.

Jan 1, 1990

By Robert C. Bates

Published information on costs of radon-daughter control in uranium mines was analyzed to develop estimates of the cost per ton for any level of radiation exposure control. All data were converted to 1967 cost of living index to provide a common analysis base. Results of the analysis show that the cost per ton increases exponentially as the radiation level is lowered. A linear relationship with the cost of living index is assumed, and equations and graphs are provided to estimate control cost per ton for any exposure control level and cost of living index.

Jan 1, 1981