Search Documents

By T. N. Patra, Sanjeeva Latchireddi, B. K. Mishra, Sravan K. Prathy

The motion of grinding balls has been the subject of study since 191 9 when Davis published the first treatise on this subject. Subsequently came the notion that knowing mill power draft, using Bond equation or others, is sufficient to do an analysis of grinding. Next, population balance models provided accurate scale-up from small laboratory size mills to very large plant size mills. However, this success was not repeated when dealing with semiautogenous grinding mill. The study of charge motion with the discrete element method provides support and answers to such issues. Besides providing an accurate picture of charge motion in large mills, the method begs the investigator to study grate and pulp lifter equally critically with fluid dynamic principles. Hence, in recent years, the field of comminution in grinding mills is advancing on a firm footing.

Jan 1, 2005

By Hardy J. Smith

The rock mass parameters which need be evaluated to estimate the rippability of rock are briefly outlined and their significance is discussed. Several methods used for estimating rippability are compared, and the advantages of taking into account a wide spectrum of rock mass parameters are emphasized. A systematic means of numerically weighing six rock mass parameters to produce a Rippability Rating (RR) is recommended, and a method of correlating this rating with the refraction seismograph method and with tractor horsepower is shown. Although the overall method demonstrated is systematic and yields specific numerical results, an integrated approach is recommended to its application, taking into account: the Rippability Rating; seismic velocity and geologic material; and other engineering judgment factors.

Jan 1, 1986

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By J. C. Cawley, J. Sottile, J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts and make the repair. Of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner and tested. This paper summarizes the development of the diagnostic system and provides examples of the system&apos;s diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Comments on the system&apos;s performance are also presented.

Jan 1, 1995

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii&apos;s Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world&apos;s first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By A. L. Hornbaker

Management of mineral resources through land-use planning procedures is not a new concept, particularly at the local level of government. Colorado may well be one of the first states, however, to vigorously attempt to evaluate on both the state-wide and regional basis, mineral resource potential and to make certain that potential for mineral resources is included as one of the primary factors considered in the local land-use decision-making process. Less than a decade ago the only consideration given to mineral resource extraction, particularly aggregate resources, was whether or not they could be produced at the particular time they were needed. This attitude has now shifted to the other extreme, not only in Colorado, but other states as well, so that other interests, especially housing projects, mountain subdivisions, recreational and wilderness areas are gaining prime consideration in land-use decisions. Ideally, in a more acceptable median position, mineral resource potential would receive definite consideration at the local level.

Jan 1, 1977

By J. S. Murty

In this paper, a report is given of studies undertaken in a laboratory rod mill to obtain the optimum conditions for the desired particle size distribution for long-distance transportation of coal through slurry pipelines.

Jan 1, 1987

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors&apos; experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By J. M. Kaufman

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is linited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized.

Jan 1, 1984

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By R. Parkins

This paper will discuss a method used to refine the fill level, and orifice size for a dual motor conveyor drive with extended delay chamber fluid couplings. The subject conveyor is located on the surface at the Mountain Coal Company West Elk Mine, located near Somerset, co.

Jan 1, 1996

By B. J. Swenty, J. L. Hubbard, R. L. Peyton

Based on the results of the National Program of Inspection of Nonfederal Dams conducted by the US Army Corps of Engineers during 1977-1981, Missouri was found to have the highest number of "unsafe" dams in the nation. Many of the dams classified as unsafe in Missouri were tailings dams.

Jan 1, 1987

By Egon Pohl, Friedrich Steinhäusler, Werner Hofmann

INTRODUCTION Anticipated increase of nuclear fuel production in the future coincides with growing concern about the occupational health risk of miners from inhaled radon decay products. As a consequence it has been suggested to even lower presently permitted exposure levels (NIOSH, 1980) and implement more stringent control on measurement programmes. Compliance with these regulations requires large investments in new or modified ventilation systems as well as in increased expenditure for staff and instrumentation for health physics operational monitoring. Since both costs are directly related to the overall ore production costs, this can have far reaching implications with regards to the economic feasibility of certain mining operations and consequently reduce estimates of low-cost minable ore reserves. In addition there is increasing evidence that the radon problem is not limited to the nuclear fuel cycle only, but can also represent a significant hazard to non-uranium miners. A key component in the cost-effective implementation of legislative control measures is the monitoring system employed. The choice of system is decisive for the total costs of installation and maintenance, manpower requirements and accuracy of nuclide determination. In the following operational specifications are defined for monitors in mining and milling environments. Different types of available instrumentation are discussed with regard to their suitability for practical radiation protection in underground mines, open cut mines and mills. ATMOSPHERIC CHARACTERISTICS Underground mines Radon in the air of underground mining operations is exhaled from surrounding rock surfaces, crushed material and, to a lesser extent, from water seepage. Whilst in uranium mines radon releasing ore bodies are generally localized in distinct areas, radon sources in non-uranium mines can be very dispersed throughout the system of mine tunnels. The ventilation scheme used influences the absolute atmospheric level of radon as well as the equilibrium conditions between radon and its decay products (factor F). In uranium mines mechanical forced-air ventilation is normally the only way to achieve and maintain legally required nuclide levels. This causes the F-factor to be rather low, e.g. in French CFA-mines F is of the order of 0.2 (Francois, Pradel, Zettwoog, 1975). At the same time the fraction of unattached radon decay products (fp) can increase due to the high air velocities employed. However, it is possible to find non-uranium mines with either natural draught ventilation only or assisted on demand by forced air ventilation during special operations or climatic conditions. Thereby the F-factor is more dependent on seasonal changes of temperature differences between outdoors and mine atmosphere and work routines. As a result F can cover a wide range from 0.02 to 0.95 (Steinhäusler, 1976). The use of filters or electro-precipitators in mine ventilation systems can modify the atmospheric characteristics twofold as it generally decreases the content of radon decay products, but at the same time increases the content of the unattached fraction fp . Average concentration levels of radon decay products are mostly lower in mechanically ventilated non-uranium mines than in equally ventilated uranium mines and are below 0.3 Working Level (UNSCEAR, 1977). However, some working places in non-uranium mines, specially with only natural draught ventilation can occassionally approach maximum permissible levels as defined for uranium mines (Strong, Laidlaw, O&apos;Riordan, 1975; Snihs, 1976; Sciocchetti, Scacco, Clemente, 1981). Open pit- and surface mines Radionuclide levels of radon decay products in the atmosphere of these mines are mostly too low to represent a significant inhalation hazard for miners, ranging typically from 0.03 to 0.1 Working Level (Steinhäusler, 1976). However, personnel using airpurifying respirators or working in cabins ventilated with filtered air can be exposed to a radon atmosphere with low value for the F-factor (F [<] 0.1) and high fp-value up to 80 % (Leach and Lokan, 1979). Mills Atmospheric radon concentration in crushing, grinding, drying and packing sections depends on the radium 226 content of the ore, ore storage methods and ventilation system employed. Providing adequate ventilation ([>] 2 air changes per hour) and control of dust production radon and its decay products represent only a minor problem (Saconney, 1979). MONITORING OF OCCUPATIONAL EXPOSURE Objectives Operational monitoring of the working places provides information on: - confirmation of appropriate control of the routine mining methods employed - indication of abnormal conditions. Although this type of monitoring enables the location

Jan 1, 1981

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader&apos;s orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature&apos;s effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By Robert S. Ondrey, Robert A. Haney, David J. Atchison

The Mine Safety and Health Administration has conducted tests to determine the effectiveness of two methods for reducing diesel particulate emissions in underground coal mines. Both methods involved collection of the particulate material before being released into the environment. One method utilized a disposable pleated paper filter attached to the tail pipe; the other utilized a reusable wire mesh screen attached to the tail pipe. This paper describes the instrumentation and testing used to evaluate both control methods. Results of respirable dust and diesel particulate measurements made underground are presented and analyzed.

Jan 1, 1992

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993