Search Documents

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By D. E. Walsh

With the exception of the development of large scale mining equipment (haul trucks, draglines, shovels, etc.), there are likely few other candidates responsible for the ability to exploit large tonnage, low grade deposits, than the development of large capacity comminution equipment and circuits; crushers and grinding mills. Ball mills are often the final step in the comminution process and are responsible for providing what should be the optimum particle size distribution of ore to subsequent mineral concentration steps in the flowsheet. Because comminution processes are such high cost centers for milling operations, both capital and operating costs, an enormous amount of research has been conducted to study and model their performance, in order to improve efficiencies (Kelsall, et al., 1969; Austin et al., 1984; Napier-Munn, et al., 1999; Powell and Smit, 2001). With respect to modeling ball mills, estimates of the breakage rates for individual size classes of ore particles are fundamental, as are the particle size class breakage functions (the progeny of particle sizes produced from breaking a coarser particle size class), also termed appearance functions. Fundamental research into particle breakage in tumbling mills focuses on how much energy is input into single particles versus how they break and what size distribution of particles results. Several test methods, including JKMRC?s well known dual pendulum test and drop weight test, have been developed for the breakage of coarse particles down to 6 mm in size (Napier-Munn, et al., 1999). Work on the breakage of finer particles is still an area of intense research and single particle breakage is being investigated as are multiple particle, fixed bed methods (Hoffler and Herbst, 1990; Bourgeois et al., 1992; Whiten, 2007).

Jan 1, 2011

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7,200 kg (15,900 lbs) per day or 61%. Metals loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change, and fewer than 1% got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2002

By D. R. Hack

Increased consumption of concrete in the Pacific Northwest has pushed aggregate resource development pressure from urban areas west of the Cascade Range to rural areas east of the Cascades. Some recent development has focused on barge and rail accessible off-reservation Indian allotments that are exempt from state and county regulations. These lands have their own unique set of challenges, especially when Federal and Tribal governments have conflicting goals and attitudes pertaining to resource development. This paper discusses issues of leasing, reclamation, Federal vs. Tribal authority, cultural resources, and the history of allotment.

Jan 1, 2002

By Albert Musschoot

The expanding applications of vibrating feeders for controlling the flow of bulk materials, and their adaptation for processing requirements, have developed considerable interest in stockpiling and reclaim systems. The general design of these units consists of a material transporting trough, or platform, driven by a vibratory force system. Design flexibility and variety is limited only by engineering ingenuity. The basic motion of the vibratory trough, or work member, is a controlled directional linear vibration that produces a material tossing or hopping action. Material travel speeds vary from 0 to about 30 m/min, depending on the combination of frequency, amplitude, and slope vibration angle.

Jan 6, 1981

By P. L. Yorio, D. R. Willmer

"The current paper presents the results of a study designed to explore the types of practices that are fundamentally important to developing and maintaining comprehensive risk-based health and safety management systems (HSMS) in mining organizations. Eighteen practicing health and safety (H&S) executives, managers, and professionals from a variety of mining commodities were asked to assess the fundamental importance of 20 distinct elements and 133 different practices assembled from a review of several HSMS consensus standards. The research approach assumes that developing and maintaining a robust HSMS requires unwavering attention to activities designed to either: 1) directly contribute to a risk management system’s plan-do-check-act cycle; or 2) build an organization’s internal infrastructure without which the cycle cannot be sustained. The results of this study suggest that the following areas require consistent focus and attention: Leadership Development; Accountability; Knowledge, Skills, and Abilities Development; System Coordination; Culture Enhancement; Behavior Optimization; and Risk Management Studies. Each element and its corresponding top-ranked and top-rated practices are discussed.INTRODUCTION Since the time of the Industrial Revolution, occupational health and safety (H&S) management has been a topic of practitioner thought and academic inquiry (1). In the U.S., decades of regulation and research have resulted in a surplus of prescriptive information (techniques, tools, approaches, standards, programs, practices, policies, etc.). With an abundance of such information, a simple H&S solution to address a problem in the U.S. mining industry may seem straightforward. Counter to this assertion, however, some evidence suggests that the abundance of information may create complexity and cause confusion in the minds of organizational leaders and H&S managers, ultimately discouraging the voluntary pursuit of a sound approach (2). In line with this perspective, in 2006 the U.S. National Mining Association (NMA) formed an independent commission to examine H&S management issues within the mining industry. The findings of the commission called for the mining industry to adopt a risk-based management paradigm. In the presentation of its findings, the commission stated that “…every mine should employ a sound risk-analysis process, should conduct a risk analysis, and should develop a management plan to address significant hazards identified by the analysis” (3). Grounded in the well-known plan-do-check-act cycle, the recommended risk management system allows for mines to ground strategic management choices in their mine-specific hazards and risk profiles"

Jan 1, 2015

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

By Wern-ping (Nick) Chen

In concrete lined tunnels, formwork removal timing may be controversial. Contractors seek to strip the form as soon as possible, and designers seek to keep the formwork in place as long as practical to protect the fresh concrete. Formwork removal timing is normally specified as a function to its insitu concrete strength. This approach may work for smaller diameter tunnels, but fallacy occurs when applying this approach to larger diameter tunnels, since a larger diameter would experience more displacement than a smaller diameter tunnel from its own weight. Excessive deformation may fail a tunnel to meet its roundness criterion and overstress the lining causing cracking or falling from the crown. This paper presents a contractual mechanism to mitigate this issue.

Jan 1, 2008

The Golden Grove Project area is located 220 km (137 miles) east of Geraldton in Western Australia (Fig. 1). The project is a joint venture involving Amax Exploration (Australia) Inc. (Amax), Electrolytic Zinc Co. of Australasia Ltd. (EZ), and Esso Exploration & Production Australia Inc. (Esso), each with 31 116% interest, and Aztec Exploration Pty., Ltd. (Aztec), with a 3 1/2% carried and a 3% contributing interest. The venture covers two significant volcanogenic massive sulfide deposits and some 40 km (25 miles) of highly prospective Archean volcanics. During the course of the past 12 years (to 1983), all four companies were responsible for operating the project at one time or another and all influenced the discoveries. The Gossan Hill and Scuddles deposits are typical examples of volcanogenic massive sulfide deposits associated with Archean explosive submarine acid to intermediate volcanic complexes. They are located in the northwesterly trending Yalgoo greenstone belt of the West Australian Archean Shield. Gossan Hill, located in 1972, is essentially a copper deposit with minor zinc lenses; to date, 97 diamond holes have delineated a geological resource* estimated to contain 13 Mt (14.3 million st) of of 3.4% Cu and 13 g/t (0.38 oz per ton) Ag in the main lenses with minor lenses totaling 2 Mt (2.2 million st) of 3.7% Cu and 17 g/t (0.49 oz per ton) Ag and 1.7 Mt (1.9 million st) grading 1.5% Pb, 14% Zn, and 87 g/t (2.8 oz per ton) Ag. Scuddles is a zinc-copper deposit with gold and silver credits. It *Resource estimate provided by Esso for inclusion in Aztec Exploration Pty. Ltd. 1982 Annual Report was discovered in 1979 and, to the end of 198 1, had been delineated with 42 diamond holes. On the basis of this drilling, a geological resource* of 26 Mt (28.7 million st) has been estimated in three coalescing lenses. The lenses comprise 7.5 Mt (8.3 million st) of 2.1 % Cu, 12 g/t (0.35 oz per ton) Ag, and 0.3 g/t (0.009 oz per ton) Au; 7.6 Mt (8.4 million st) of 0.4% Cu, 9.9% Zn, 73 g/t (2.3 oz per ton) Ag, and 0.7 g/t (0.02 oz per ton) Au; and 1 1.0 Mt (1 2.1 mil lion st) of 1.1 % Cu, 9.3% Zn, 8 1 g/t (2.6 oz per ton) Ag, and 1.5 g/t (0.044 oz per ton) Au. Readers are referred to Frater (1978) and Harris et a). (1982) for a more detailed geological account of these deposits.

Jan 1, 1991

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched.

Jan 1, 1999

In subterranean mining operations, access to communication networks deep underground is critical for transporting data, voice and video, and other supporting applications that are essential for efficient and safe operations. Whether accessing sophisticated ERP or maintenance management systems, engaging in fleet management, video surveillance, or access control, or protecting miners with wireless locator systems, these networks serve as a literal lifeline between workers deep within mines and surface operations. For this, mining networks require more than permanently installed network cabling, it also requires unique deployable systems designed for quick installation, extension and even relocation as the active mine site area moves, or equipment is moved in and out.

Mar 1, 2014

By Gleason

"From June 16 to 19, more than 1,400 tunneling and underground construction professionals gathered in Chicago, IL for the bienial Rapid Excavation and Tunneling Conference (RETC). There, they were greeted by a full technical program and an exciting exhibit hall that provided a comprehensive look at the world’s bustling tunneling and underground construction industry.The successful conference was a reflection of the industry itself, which is to say, busy. As much of the world has begun to focus on creating a cleaner and greener environment, the global tunneling industry has seen an uptick in infrastructure projects move from design-build to construction phase. With a global shift away from the use of fossil fuels, major cities around the world are looking to increase public transportation options, which leads to the need for more transportation tunnels. And as urban populations continue to grow, the need for clean water calls for more tunnels, and as urban footprints continue to expand, the need to increase and update combined sewage overflow tunnel grows with them.During two and a half days, more than 20 sessions covering all of these topics were presented at the Hyatt Regency in Chicago, many to packed rooms in which every seat was taken and people were standing along the side and back walls.RETC is a biennial conference and one of the largest in the North America for the tunneling and underground construction industries. As such, it hosts a robust exhibit floor. This year 172 vendors occupied 205 booth spaces. The exhibit included everything from tunnel boring machine manufacturers, like Robbins and Herrenknecht, to the companies that supply all kinds of parts and services to the industry."

Sep 1, 2019

By Martin Herrenknecht

Tunnel boring machines continue to develop to take on not only larger and larger diameters but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar has required innovative design approaches. A systems approach has been required to produce tunnelling machines that can not only safely excavate the tunnel but do so in an efficient, cost effective manner that stresses production and labor saving approaches. This paper will review the current design developments and present recent projects where these most recent principles have been applied.

Jan 1, 2008

By Thomas de Lange

Extensive test work performed on the Coalscan 3500 ash analyzer at the Grootegeluk Coal Mine has led to the successful implementation of on-line ash monitoring to control the quality of coking coal and power station coal. Test work results are given and the advantages of on-line bias compensation discussed. Some details of the quality control systems subsequently implemented are also highlighted. Finally, the economic benefit of on-line ash monitoring based on the Mayer curve is demonstrated.

Jan 1, 1992

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.