Search Documents

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023

By D. C. Fuller

CoaLiquid, Inc. (CLI) has been in the coal- oil-mixture (COM) business for over five (5) years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August of 1979. For over two (2) years CLI has been expanding its efforts and conducting large scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit. CoaLiquid has conducted commercial scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.

Jan 1, 1982

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

By L. Berwick, A. Karunanayake, D. Skutt, H. Heath, J. Wang

Thallium (Tl) is a highly toxic heavy metal, soluble over a wide pH range. Tl levels may exceed discharge limits in mining-influenced water associated with processing gold, lead, cadmium, zinc, and copper ores. In this work, the effect of sodium permanganate (CARUSOL® C liquid permanganate) on Tl removal from mining wastewater was studied. Factors influencing Tl removal, namely permanganate dosage/demand, coagulant and flocculant use, order of chemical addition, and co-existing metal ions were examined. The results show that permanganate addition is very effective at removing Tl to below target limits and can provide a unique solution for improving wastewater quality and optimizing overall treatment costs. In addition, several on-line monitoring techniques were evaluated for process optimization. The Hach DPD Free Chlorine method was optimal, allowing plant operators to rapidly and easily spot check effluent samples for excess permanganate dose.

Mar 2, 2022

By Liuming Wu, Willis Forsling

The complexation of Alizarin Red S (ARS) at the surface of hydrous fluorapatite particles has been investigated at 25.0 C by means of potentiometric titrations, adsorption experiments in 0.1 M NaCI ionic medium, and Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFT) studies. A chemical model describing the reaction at the aqueous mineral surface has been established under equilibrium conditions according to the reaction [== -CaOH2 + HA2 - « _ =PO CaA2 - z + H30&apos;; to (int.) = -5.61 ± 0.02 3 a =PO- logBs-1110(int.) ( ) within the range 8.40 <_ -log[H ] <_ 9.80.] Experimental data were evaluated using the computer program FITEQL on the basis of a constant capacitance model for the electric double layer. The surface complex structure, has been proposed to involve the quinoid and alpha phenolic oxygens of ARS coordinated to the calcium sites on the fluorapatite surface.

Jan 1, 1993

By T. Rudolph, M. Pawlik, J. Benndorf, X. Yin, J. F. Brune, P. Goerke-Mallet

The long and often undefined period in the post-mining phase challenges geo-monitoring with its various responsibilities, like the detection of environmental changes, ground movements and water management. Modern methods of geo- and environmental monitoring observe numerous aspects using active and passive sensors with multispectral, hyperspectral and microwave sensors, with diverse spatial dimensions and spatiotemporal resolutions from satellites, Unmanned Aerial Vehicles (UAVs), in-situ sensors. Data integration, together with on-site knowledge and experience, provides the basis for comprehensive modeling, which improves the understanding of the environmental changes and their related causes, which is an essential step for public acceptance. In this paper, we aim to give a brief overview of various geo- and environmental monitoring methods.

Mar 2, 2022

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author&apos;s company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By R. DasGupta

The dissolution behavior of gold in ammoniacal solutions at 75°C has been investigated. The variables investigated include concentration of lixiviants, pH of the solution and various oxidants. The anodic dissolution of gold was studied in the absence of oxidants using the potentiodynamic polarization technique. The cathodic reaction of oxidants was studied on a platinum electrode. Tafel polarization tests were also performed to determine the dissolution rate. The overall dissolution of gold in ammoniacal solutions was examined using a mixed potential theory. A comparative study on the role of cupric am mine, oxygen, hydrogen peroxide, sodium hypochlorite as oxidants for the dissolution of gold in ammoniacal solutions has been carried out.

Jan 1, 1996

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By Lance Rasband, Richard Hanke, John Starcevich

"Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m (14.9-ft) thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal m (400 ft) of jet grout improved soil at a rate of slightly more than 1.6 m/d (5.3 ftpd). It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s second largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m/d (36 ftpd). By the end of October 2013, Bertha had mined roughly 131 m (430 ft), averaging 1.4 m/d (4.7 ftpd), and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m (800 ft) mark and Bertha was averaging 3.6 m/d (11.9 ftpd), achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on Dec. 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm (0.9 in.) diameter monitoring well casing, previously installed by the Washington State Department of Transportation (WSDOT) to monitor groundwater conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jun 1, 2016