Search Documents

By Ekkehart Mertins, Hans-Dieter Wasmuth

During the last years many new concepts have been presented for magnetic separation of feebly magnetic minerals by using the new high-duty permanent magnetic material especially in Open Gradient Magnet Systems (OGMS). In this respect KHD Humboldt Wedag AG developed an improved version of a drum-type magnetic separator called PERMOS® with a special magnetic field configuration for the NdFeB permanent magnets, which gives a magnetic field strength of at least 0.7 Tesla and a wide working zone outside the drum. The magnet system within the PERMOS® unit is no longer made of relatively large magnet blocks of alternating radial magnetisation; the system is now made up of a multitude of small NdFeB bars with a specially oriented magnetisation. This PERMOS® Open Gradient Magnetic Separator can be used for dry magnetic separations in "top-feed" and 'free-fall" feed configuration as well as in the conventional wet "drum-type" feed mode. It allows high throughput rates of up to 40 metric tons of solids per hour and meter of drum length without any clogging problems, even when strongly magnetic com-pounds are present in the feed material. The important design features and the actual machine characteristics of the improved PERMOS® units for dry and wet magnetic separation are described and typical examples for their commercial application for industrial minerals and for martitic iron ores are presented.

Jan 1, 1995

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By Kevin Fitzpatrick, Carmen Scalise, Patrick Jensen

"The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) owns and operates the Tunnel and Reservoir Plan (TARP) system which was adopted in 1972. TARP is a network of 110 miles of deep tunnels and ultimately 3 large reservoirs to combat waterway pollution and flooding within a 350 square mile area served by combined sewers. The original TARP concept included additional tunnels to convey CSOs from the largest storms to the reservoirs. With the initial TARP tunnels complete and the reservoirs nearing completion, MWRDGC commissioned hydraulic and hydrologic modeling studies to analyze the benefits of additional conveyance tunnels. These updated studies optimized the configuration of additional tunnels considering integration with potential future local sewer system upgrades. The alternatives considered several routes of 25, 30, and 35 foot diameter tunnels, ranging from 10 to 18 miles. Alternatives were analyzed based on projected reductions to basement flooding compared to the relative costs. TUNNEL AND RESERVOIR PLAN After World War II the Chicagoland area underwent rapid growth and development. With the Metropolitan Water Reclamation District of Greater Chicago's (MWRDGC) service area becoming increasingly impervious, the flat Chicago landscape was increasingly at risk of significant flooding. In the mid and late 1950's, Chicago experienced multiple extreme storm events that had significant impacts on the city and generated the momentum necessary to initiate what would ultimately become one of the world's largest civil works undertakings. In 1957 a Flood Control Coordinating Committee was formed, consisting of representatives of the MWRDGC, Illinois Department of Public Works, Cook County, and the city of Chicago, to review various plans and develop recommendations for a course of action. With more than 50 alternative concepts being identified, the Tunnel and Reservoir Plan (TARP), which itself is a composite of various alternatives, was adopted the by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) in 1972. The need to adopt a long term plan was further influenced by the Clean Water Act, which was enacted only 8 days prior."

Jan 1, 2016

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By J. D. Noll

An effective technique to minimize miners? respirable dust and diesel exposure on mobile mining equipment is to place mine operators in enclosed cabs with designed filtration and pressurization systems. Many factors affect the performance of these enclosed cab systems, and one of the most significant factors is the effectiveness of the filtration system. High-efficiency particulate air (HEPA)-type filters are typically used because they are highly efficient at capturing all types and sizes of particles, including those in the submicron range such as diesel particulate matter (DPM). However, in laboratory tests, minimum efficiency reporting value (MERV) 16 filters have proven to be highly efficient for capturing DPM and respirable dust. Also, MERV 16 filters can be less restrictive to cab airflow and less expensive than HEPA filters. To verify their effectiveness in the field, MERV 16 filters were used in the enclosed cab filtration system on a face drill and roof bolting mining machine and tested at an underground limestone mine. Test results showed that DPM and respirable dust concentrations were reduced by more than 90% when the cabs were properly sealed. However, when the cab door was opened periodically throughout the shift, the reduction efficiency of the MERV 16 filters was reduced to 80% on average.

Feb 1, 2014

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By Marcus Digre

The autogenous grinding method has been progressively employed in mineral dressing plants during the last 15 years. The term has been used with somewhat different meanings (1), (2), (3). In this paper the author will use it in the most restricted way, for processes where run-of-mine ore (rock) in one step is reduced to a grind product by the action of the ore itself without any other grinding media present. The pebble grinding process where the major part of the ore enters the mill as finely crushed product which is ground further with selected coarse ore pieces acting as grinding media, is not considered autogenous grinding. Processes where a minor amount extraneous media as steel-balls is added to supplement an autogenous mill charge will be called semiautogenous. Other terms need also to be defined. "Mill charge" will be used about the active part of the mill content which performs the grinding, that is the steel balls in ball grinding and the coarse ore pieces in pebble and autogenous grinding. The interstitial nearly finished material is not included in the term "mill charge", and for the wet grinding operations is called the "mill pulp' The term "pebble" will be used for any rounded ore or rock piece in the mill charge whether it is an autogenous or a pebble grinding operation.

Jan 1, 1970

By W. R. McDonald

The U.S. Department of the Interior, Bureau of Mines, conducted field tests on acidic copper tailing as part of its program to devise, improve, and demonstrate technology for stabilizing mining and mineral processing wastes. Results will be presented from successful 1/8-acre and 1-1/2-acre demonstration revegetation plots established in 1973 and 1974 on an abandoned copper tailing pond located on public land adjacent to Holden Village, Wash. The tailing was neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Plant growth covering 60 percent of the surface was achieved on both test plots. Regar brome, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. In neutralizing the tailing, the target pH of 6.8 was not achieved; however, good plant growth occurred in areas where the pH ranged from 2.9 to 5.8.

Jan 1, 1979

By Z. D. Yu, J. E. Gebhardt, D. I. Phillips, S. X. Jiang, R. Z. Zhang

The potential application of flotation for the treatment and processing of a fine-particle coal stream was investigated for the Chaili Coal Washery of the Zaozhuang Coal Mine Administration, Shandong Province, China. A goal of the test work was to evaluate the application of the Microcel™ flotation column and compare its performance to conventional flotation. Small-scale flotation tests were performed in the laboratory and on-site with fine coal slurry samples from the plant thickener underflow, i.e., the washing plant's undersized reject material. Flotation tests were conducted on-site with a 7.6-cm diameter Microcel™ column and with small-scale conventional cells. Column flotation tests were performed to determine a recovery-grade relationship for the fine coal feed, which contained about 24% ash, and to obtain sufficient data to enable scale-up to a large diameter unit. A primary objective as to establish the maximum throughput capacity of a Microcel™ flotation column while operating to produce a clean coal product with ash content of 7.5-7.8%. Results of the test work indicate that this product quality could be achieved at feed rates of 15-19 tph to a 3-m diameter Microcel™ flotation column. Lower ash products, i.e., 5-7% ash, were obtained but at lower column throughput capacities. Comparative flotation tests, conducted with conventional flotation cells, indicated that a product ash of only 8% or greater was achieved in a single-stage test.

Jan 1, 1995

By P. Raffinot, C. H. G. Bushell, S. Hodgson, E. F. Milner, H. J. Bosshardt, N. Draper, D. E. Pickett, Edwin T. McKnight, J. Prieto

Zinc ranks third and lead fourth in world nonferrous metal conumption. In 1972 the free world consumed 3,333,000 mt of refined lead and 4,422,000 mt of refined zinc. The lead tonnage was divided into the following end uses: storage batteries (42%), lead allows (7%), pigments and chemicals (11%), cable sheathing (9%), gasoline additives (13%), pipes and sheets (8%), and miscellaneous uses (10%). The corresponding distribution of zinc uses in 1972 was galvanizing (39%), die casting (26%), brass (15%), rolled zinc (8%), oxide excluding American Process zinc made directly from concentrate (6%), and other uses (6%). The pattern of usage of lead and zinc varies considerably from country to country. During 1972 in the USA 49% of refined lead was consumed in storage batteries, 19% in gasoline additives, and only 3% in cable sheathing, whereas in the United Kingdom 28% of the lead was consumed in batteries, 14% in cable sheathing, and 14% in gasoline additives. For zinc the major US uses were die casting (41%) and galvanizing (37%), with about 3% consumed as rolled zinc; corresponding usages in the same applications in France were 12, 28 and 28% and in Australia 12, 67, and 3%, respectively. The outstanding resistance of lead to corrosion, its density, and

Jan 1, 1985

By L. Adler

A fairly complex analysis is required to select, or evaluate a piece of excavating and bulk handling equipment and obtain its performance. At present there is little agreement as to what specific points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment from the bulldozer and the continuous miner, to the B.W.E. The importance of the equipment characteristics, job activities, and work conditions are stressed and separate analytical stems are established in a flow chart for these. They are combined using suitability tests in the following steps: 1) problem statement, 2) natural conditions, 3) suitability guidelines, 4) appropriate equipment types, 5) operational activities, 6) encumbered space, 7) geometric design, 8) equipment sizing, 9) failure and limits, 10) performance and consumption, 11) public policy checks, and 12) costs and profitability. Public policy and economics while considered throughout receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1983

By John E. Frost

Duval's (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval's entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval's interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco's properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco's properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By J. F. Allan

The main conditions which affect investment in mineral exploration and development are compared in five countries currently considered attractive for mineral investment - Canada, the U.S., Australia, Brazil and the Philippines. The primary parameters - the probability of occurrence and discovery of mineral deposits and the short and long term viability of mineral development - are evaluated and compared on a relative basis by a form of factor analysis. This analysis indicates that of the five countries studied, Canada is second only to the United States in degree of favourability for mineral exploration and development.

Jan 1, 1976

By Christine M. Kammer

In 1852, six barrels of iron ore were loaded aboard the steamer Baltimore at Marquette, MI, after a trip by mule wagon from the nearby Cleveland Iron Mining Co. Shipped to Sault Ste. Marie, they were portaged around rapids and reloaded onto another ship for the final journey to the steel mills of Cleveland. In 1855, the same company-the predecessor of Cleveland-Cliffs Iron Co.-chartered the brigantine Columbia to carry the first iron-ore cargo through the newly opened Soo locks. In 1981, about 2,190 iron-ore shipments in the form of taconite pellets were transported by water from US Great Lakes-ports. The total volume during the 284-day shipping season was 63 Mt (62 million It). Counting Canadian ship¬ments, almost 76 Mt (75 million It) of iron ore were moved on the lakes last year. The five Great Lakes-Superior, Huron, Michigan, Erie, and Ontario-contain 20% of the world's fresh water. The area surrounding the lakes has 26% of the nation's populations, 47% of its steel production, and over 80% of the raw materials required to make steel. That figure includes 71% of the country's iron ore and 40% of its limestone. Only the availability of low-cost water transportation of raw materials has kept the heartland steel producers competitive. Iron ore shipped on the lakes originates in the Lake Superior district's Mesabi and Marquette iron ranges. Major mines and their principal partners are Cleveland-Cliffs Iron Co.'s Empire, Republic, and Tilden; Armco and Republic's Reserve Mining Co.; Oglebay Norton Co.'s Eveleth; Hanna Mining Co.'s National and Butler; Inland Steel Co.'s Minorca; Pickands Mather & Co.'s Erie and Hibbing, the latter operated in conjunction with Bethlehem Steel Corp.; and US Steel Corp.'s Minntac. Pelletized ore products at these facilities is shipped through seven principal ports on the upper lakes: Duluth, Two Harbors, Silver Bay, and Taconite Harbor, MN; Superior, WI, and Marquette, MI, on Lake Superior; and Escanaba, MI, on Lake Michigan. In 1981, tonnage volumes ranged from 13.3 Mt (13.1 million It) shipped from Duluth, to Marquette's total of 5.4 Mt (5.3 million It). The ore docks, with two exceptions, are operated by railroads, most of which are owned by mining companies. Table 1 illustrates US iron-ore shipments in 1981. In the lower lakes, ore is discharged at dock facilities close to the great steel-producing centers of Chicago, Detroit, Cleveland, Pittsburgh, and Buffalo. Between the mines and mills, lakes and connecting waterways form one of the country's most effective transportation systems. Each year, vessels on the Great Lakes transport about 181 Mt (200 million st) of bulk industrial and agricultural materials-a greater quantity at a lower cost than can be achieved by any other transportation mode. Major commodities in Great Lakes trade are iron ore, coal, grain, limestone, cement, sand, and petroleum products. About 125 US flag vessels serve this trade, among them 13 "1,000-

Jan 10, 1982

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983