Search Documents

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By J. W. Leonard

Gravity based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets; but, because of historic control problems, recovery is frequently sacrificed to achieve quality resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grab-sample on-the-spot sink-float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is both serious economic as well as environmental losses. While the economic losses are obvious, less obvious environmental losses, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. A control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has until recently escaped technology.

Jan 1, 1991

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Pedro D. Lasota

Chile leads the world in copper production with an annual capacity nearing 2 Mt (2.2 million st). Most of the country’s copper production, about 74%, is mined by open-pit mining methods. Open-pit mining also accounts for a major portion of Chile’s production of other commodities, including iron, gold, silver and coal (Table 1). Chile’s mining boom began 10 years ago and is expected to continue through the end of the decade. From 1980 to 1990, copper production in Chile increased 48.7%. During the same period, gold production increased 303%, silver production increased 119% and coal and iron ore production increased 163.7% and 6.6%, respectively (Table 2). It is estimated that copper production will be in the order of 2.3 Mt (2.5 million st) by 1996, when new projects now under construction come onstream. Gold production could reach 35 t (1.1 million oz) and coal production could increase another 1 Mt/a (1.1 million stpy). Open-pit mining has played a significant role in Chile’s minerals production growth. The expected increases in mine operations will come about mainly through new open pits or expansions of existing surface operations (Table 3). However, the number of open-pit copper mines will decrease from 74% to 66% of the total number of Chilean mines. Gold mines will increase from 63% to 69% of the total, while coal mines will go from 41% to 59%. Most all of the present iron ore production is from surface mines and will continue that way.

Jan 1, 1992

By Emily Wortman-Wunder

Attendees at December?s Arizona SME Section Conference at the Hilton El Conquistador Resort outside of Tucson, AZ were feeling optimistic and ready to get to work after a year of steady growth and recovery in the mining industry. During the two-day event (Dec. 5-6, 2010) and the preceding American Mining Hall of Fame banquet and awards ceremony, the focus was on copper, worldwide population growth and regulatory pressures, with several smart new projects featured alongside updates to traditional large-scale copper development projects. Keynote speaker Timothy Snider, chair of the University of Arizona?s Lowell Institute for Mineral Resources, hit the mood of cautious optimism when he analyzed the global demand for resources, using the case example of copper. Over the next 20 years, he said, the world?s population is expected to grow to 9.2 billion and the average annual per capita copper use is expected to rise from 2.2 to 4.5 kg (5 to 10 lb). The increase in demand will provide tremendous opportunity for mining companies, he said, but cautioned that the opportunities are balanced by negative influences on demand and pressures on supply. While demand for copper is currently growing, Snider noted that there were significant downward pressures on demand as well. These included a western world that is overbuilt, in-creasing use of substitute materials in new construction and the rise of wireless devices. He also noted new regulatory pressures, and pointed out that resource development now had to occur within a context of sustainability on several levels.

Jan 1, 2011

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone; such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1985

By Ireneusz Tomza, Jolanta Lebecka

INTRODUCTION Radioactive deposits were observed in 1972 in some of the Upper Silesian coal mines. They were located mainly in the drains in galeries and on the inside surfaces of water pipes. They also caused some problems by accumulating in water pumps. It has been postulated that the deposits are produced by natural radioactive waters seeping from the rocks. Investigations were initiated to answer the following questions: - What is the composition and the amount of radioactivity in the deposits? - What radioisotopes are present in the water? - How are the radioactive deposits formed? - Do the radioactive waters also occur in other mines? - How does the radioactivity of the water depend on chemical composition? - What is the origin of the radioactive water? - Does the water and the deposits cause radiation hazards for miners? -How can the radiation hazard be reduced? METHODS OF MEASUREMENT Determination of Radium Isotopes in Water The commonly used methods of radium determination in water are either based on measurements of the radioactivity of 222Rn which is in equilibrium with 226Ra, or on the detection of alpha particles of the radium radioisotopes after chemical separation of radium from the water sample. The method based on radon activity measurements is very sensitive and does not require any chemical Separation, but it can be used for determination of 226Ra from the uranium series only, because the thorium daughter 220Rn has too short a half-life (55s to yield the required accuracy. The method developed by Goldin, 1961 [2] involved alpha-particle measurements in thin layers of RaS04 and BaS04 separated from the water. This method is not convenient for saline water and water with high barium concentration because the amount of barium carrier in this case is too large to obtain a thin layer of precipitate with sufficient activity. The Upper Silesian carboniferous waters are often saline with high barium content, so the method described by Goldin was not convenient for this case and it was necessary to change the detection system and modify the chemical preparation. The procedure developed by the authors for the determination of radium isotopes in water was as follows: - Depending on the Ba2+ content and the required sensitivity of measurement, a water sample of 200 cm3 to 3 dm3 was taken. - 10 cm3 of 0.25 M citric acid and 5 cm3 15M ammonia was added to form complex Ba2+ ions and avoid the immediate precipitation of BaSO4. (This was repeated as long as the addition of BaC12 did not form a precipitate.) - 1 cm3 of 1N solution of Pb(N03)2 as a carrier for radioactive isotopes of lead and 10 cm3 of 0.1 N BaC12 as a carrier for radium were added. - The sample was heated to the boiling point and the precipitation of RaS04, BaSO4 and PbS04 with 50% H2SO4 was carried out. - After several hours the sample was centrifuged and the precipitate was purified by washing with nitric acid and distilled water. - The precipitate was then redisolved in 20 cm3 0.125 M Na2EDTA and 3 cm3 6M ammonia and reprecipitated from the solution by dropwise addition of acetic acid to d pH of 4.5. At this value of pH, precipitation occurs only for the barium and radium sulfates, while lead and all other radioactive elements remain in the solution. The date and time of deposit precipitation was recorded. - The final barium-radium sulfate mixture was washed with distilled water and transferred to standard measurement vials. - Each vial containing a deposit had 6 cm3 of distilled water added and was then shaken vigorously. 12 cm3 of liquid gelling scintillator (INSTA-GEL UNISOLV-1 type) was then added and the vi 1 was shaken again. After a while the scintillator turns into a milky gel in which the deposit is uniformly distributed. - The standard sample of 226Ra was prepared in the same way. - The activity of the samples was measured using a liquid scintillation spectrometer. (In this case the TRICARB 3320 produced by Packard Instruments, was used). Tests run on standard radium solutions provided by Amersham Radiochemical Centre indicated that this method of measurement enables one to achieve an efficiency of almost 100% (within measurement error). For alpha particles no quenching effect was observed for the BaS04 concentration in the range up to 80 mg of BaS04 per 1 cm3 of liquid scintillator coctail (Fig. 1). This provides a sensitive determination of radium in water with high barium content and also in saline water. In saline water the solubility of barium sulfate is much higher than in

Jan 1, 1981

By III Feeley

Coal is the nation&apos;s most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By P. A. Mingione

AEROPHINE® 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn-and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treat-ing different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.

Jan 1, 1991

By Herbert P. Haschke

I. Changes made by the Economic Recovery Tax Act of 1981 (ERTA) which have an effect on investing in tax shelter investments A. Maximum ordinary income tax rate on individuals is now 50%. B. Maximum tax rate on long-term capital gains for individuals is now 20%. C. Maximum tax rate on alternative minimum taxable income for individuals is now 20%. D. Although not changed, the "add-on" 15% minimum tax on tax preference items and the possibility of paying the alternative minimum tax cause individual U.S. income tax planning to continue to be very complex. II. Real Estate A. The new Accelerated Cost Recovery System of depreciation (ACRS). 1. Mandatory for assets placed in service after 1980. ACRS will eliminate most if not all controversies with the IRS over depreciation. 2. Real property now depreciated over 15 years. Component depreciation is not available. 3. Accelerated depreciation is available - a 175% declining balance method with an automatic shift to straight line method at the optimum point in the asset&apos;s life. Alternatively, a taxpayer can elect to use the straight line method.

Jan 1, 1982

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other&apos;s supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

Although there was a significant improvement in the world economy, recovery in the iron and steel industry followed its traditional pattern and lagged the general economic recovery in 1983. World crude steel production increased from 645 Mt (711 million st) in 1982 to 664 Mt (732 million st) in 1983, an increase of less than 3%. Domestic iron and steel production showed a modest increase over 1982. Weekly raw steel pro¬duction levels ranged between 1.5 and 1.75 Mt (1.6 and 1.9 million st) for the last 10 months of 1983, compared with less than 1.25 Mt (1.4 million st) for the last half of 1982. The peak was 2.5 Mt (2.7 million per st) per week in 1978-79. This how level of steel operations kept most pelletizing and sintering operations at curtailed production levels. Extended shut-downs of pellet plants were also common. Pressure by management to reduce operating costs has continued with an increasing emphasis on maintaining quality and efficient unit productivity. With the extended decline, there have been significant personnel reductions in both operating and headquarters staffs. Many companies are anticipating a long-term how growth period in the iron and steel sector. Pelletizing Domestic pellet production showed a slight increase last year to about 34 Mt (38 million st), less than 50% of total capacity. What is indicative of the inevitable is the announced intention to chose down facilities, such as US Steel Corp.&apos;s Atlantic City ore operations pellet plant at Lander, WY, and the recent aborted move by US Steel to purchase National Steel with the apparent intent to chose the National pellet plant in Keewatin, MN. There is excess domestic pellet capacity that will not be needed. The question is what form attrition will take. South American pellets can be brought into the Chicago area at a cost competitive with Great Lakes plants. This raises the possibility that imported pellets can, in fact, displace domestic pellets at almost any US steel plant. The need to re duce total production costs at domestic pelletizing plants is crucial. Efforts to reduce fuel costs for pelletizing have focused on re placing natural gas or fuel oil with coal. More recently, petroleum coke has become available at an attractive cost, but systems must cope with its higher sulfur con tent, which limits its potential The direct firing of grate-kiln systems with pulverized coal hay been fully proven. The use of solic fuel in the straight-grate process however, is still being developer and no straight-grate system i running on solid fuel alone. The further development o coal-water slurry systems may provide a suitable fuel for both systems. It would appear, how ever, that the same ash quality restriction would hold for coal water systems as for direct-firin systems. So, the choice is based of the relative cost and convenience of a wet-grinding system with additives, compared with a dry-grind direct-fired unit. The high-temperature (two stage) heat recuperation system installed at US Steel&apos;s Minnta plant (Step III) has provided the fuel savings anticipated, any modification of additional in durating lines is planned. Other operators are hooking at similar heat recuperation improvement. Another area of potential cost savings has been in the reduction of bentonite requirements. A CCI&apos;s Tihden plant, major improvements have been made in this area. Progressive bentonit reductions were achieved over several years from the 8- to 9-kg (16- to 18-lb per st) range to the 5-k (12-1b) level by progressive moisture reductions and chose attention to operating practice. Further reductions were achieve by raising bentonite specifictions. In this instance, the wate plate absorption test specifia

Jan 5, 1984

By Donald J. Reining

The California Surface Mining and Reclamation Act (SMARA) is the nation&apos;s first legislation establishing a statewide mineral resource policy governing mining activities that recognizes regional needs and retains local autonomy. The Southern California Rock Products Association supported this proposed legislation. It was through our efforts that SMARA was passed in 1975. The local planning and zoning processes, which are so critical to the mining industry, have been significantly improved with implementation of SMARA. Recognition of the importance of the mining industry is now being developed by the State Mining and Geology Board and the California Division of Mines and Geology (CDMG).

Jan 1, 1984

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various&apos; shapes in sound rock.

Jan 1, 1967

By P. Conrad, S. Rosenthal

"Engineers remain in demand. Job opportunities in the United States still exceed the number of students graduating from college with degrees in Mining Engineering. Although enrollment is up for freshman studying Mining Engineering, many of those students will either change majors or not complete their degree, maintaining that deficit of available Mining Engineers. What can be done to ensure that enough Mining Engineers will graduate to fill the needs of the mining industry over the next ten to 20 years? The authors believe that this need can be met by recruiting students to Mining Engineering programs who are genuinely interested in working in the mining industry. With this in mind, Montana Tech conducted its first Mining Engineering camp in July 2014 to get junior and senior high school students interested in careers in the mining industry by showing them that Mining Engineering is both an exciting and rewarding career. This paper discusses What a Blast! The 2014 Montana Tech Mining Camp. INTRODUCTION The concept of summer camps for high school students is not new. For example, Missouri University of Science and Technology has offered their “Explosives Camp” for several years. A large percentage of attendees to these camps discover or confirm an interest in Mining Engineering and enroll in the school’s program. The Dean of the Montana Tech School of Mines and Engineering challenged department heads to develop and offer summer camps for prospective high school students to get a taste of engineering with the goal being to improve recruitment for each discipline. Mining Engineering embarked on the concept of a summer camp in 2013 with a concept to provide a week’s experience in Mining Engineering during the summer of 2014. What it takes to progress from concept to reality, with some of the learnings to be shared, follows."

Jan 1, 2015

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By Brenda B. Mehnert

Long-term monitoring is necessary to successfully develop predictive subsidence models. Thus, the Illinois Mine Subsidence Research Program (IMSRP) has documented subsidence over a longwall mine in south-central Illinois throughout a 3-year period. No monitoring results of this duration have been previously published for longwall mining in Illinois. To study the effects of surface subsidence and the rate of subsidence, precise level surveying was conducted at the site two or three times a year. Level surveys were conducted at approximately the same time of year using a WILD NA-2 level with a micrometer. Second-Order, Class-I, closure errors were obtained in each survey. Survey monuments were designed to minimize frost-induced movements. At this particular site in southern Illinois, subsidence over chain pillars and the panel centerline continued 3 years after mining. Since mining in 1988, 6.67 feet of subsidence or 70% of the extracted height has been documented over the panel centerline, with almost 0.30 feet in the last two years. The area over the chain pillars has subsided a total of 1.44 feet, with 0.44 feet occurring within the last 2 years. Monitoring over the chain pillars and at the centerline shows the residual subsidence to be fairly uniform. Monitoring is continuing over both of these areas. Long-term monitoring data can be used to improve evaluation of subsidence effects on land and structures. However, coal companies will time mitigation activities depending on other factors including the threshold of structural damage, type of repair needed, and maintenance of landowner and company relations.

Jan 1, 1986

By J. D. Miller, C. L. Lin

A PC, image-based, on-line instrument for measuring coarse particle size on a conveyor belt is under development. The hardware and software required to implement such a system are discussed, including the interface for the special image-acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1994