Search Documents

By E. Rigopoulos

Mining disturbs the environment, even when the ores or the minerals extracted are non-toxic. Silver & Baryte Ores Mining Co S.A (S&B) is committed to minimizing the environmental impacts of its mining activities, by implementing an integrated rehabilitation program wherever it operates. The paper discusses the principles for mining-disturbed land restoration activities on Milos Island for a successful outcome.

Jan 1, 2003

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14' horseshoe tunnel in rock, a 95' deep work shaft on shore, and a 50' deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100' in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

By Musa I. Marto

The theory of ore flotation has developed at a rather fast rate and the application of theory to practice has been successfully investigated. Significant technological advances have been made in such areas as control of the ore grade, automation in metallurgical control through conductivity measurements, and the development of faster and continuous analytical techniques for ore pulp analysis. Further significant improvements in mill control are being_ investigated through the application of a computer control to the process. This represents the more advanced trend in process control. At the heart of a control system installation, the digital computer will communicate directly with process instrumentation, perform' complex calcu¬lations to determine on a timely basis the control settings for attaining optimum results and automatically furnish signals to effect control actions. The process is considered as an integrated unit and economic criteria are used to measure its performance. The approaches to a mathematical model development to describe the process, optimization and control schemes as applied to an ore beneficiation process will be discussed.

Jan 1, 1962

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962

A charge of the Research Council of the Society for Mining, Metallurgy and Exploration, Inc. (SME) is to ?? identify longer term research ideas/needs, that in the perception of the SME Research Council, could represent significant technology breakthroughs ?? (SME, n.d.). In 2008, the Council decided that instead of unilaterally developing a list of top priorities, it would involve the entire membership of SME in identifying the top priorities. Additionally, it decided to keep the list short. This paper describes the process and results from that exercise.

Jan 1, 2010

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959

By R. Freer

Recent developments in expanded PTFE membrane filter cloths offer high flow rates and sub-micron particle removal. These high strength, industrial grade filter cloths can be tailored for tubular filters, leaf filters and rotary vacuum drums. Filtration techniques using tubular filters make possible filtration of difficult slurries with the elimination/reduction of filter aids and chemical additives. This paper describes principles of surface filtration, applying the membrane filter cloth and comparisons to gravity separators. Benefits to the mining industry include clear effluent, enhanced solids recovery and accelerated cost payback.

Jan 1, 1996

By C. J. Webb

Abandoned uranium mines in the southern Black Hills of South Dakota were sampled for uranium, radium, and rare earth elements during 1992 and 1993. Analyses of water samples from several shallow ponds in the mine pits showed pH values between 3 and 4 with uranium concentrations between 1600 and 2600 ppb. Rare earth elements and their respective isotopes were analyzed with an inductively coupled plasma mass spectrometer and were referenced to a shale normalization pattern. All samples showed an enrichment in the middle rare earth elements. Rare earth levels often were greater than 0.2 ppm. At one site, the concentrations of lanthanides were 150,000 times above background levels. While the southern Black Hills have long been known for rich uranium ore deposits, these analyses show that significant levels of rare earth elements also are present, indicating that the potential exist for future development.

Jan 1, 1995

By Ken E. Baylis

Current over-capacity in coal production provides assured and relatively low-cost supplies to coal importers. At the same time, it is of serious concern to coal producers who invested considerable sums in the expectation that overseas demand would continue to grow rapidly. This paper assesses the reserves available for export, the export facilities, the coal supplies which can be put through them, and the market prospects for the future. It assumes, rightly or wrongly, that there will be no major and prolonged disruptions in supply from any major sources of coal. COAL RESERVES FOR EXPORT Economically recoverable reserves in the non-communist world amount to about 470 billion tonnes. These are sufficient to sustain current production levels of 2 billion tonnes a year for 235 years.

Jan 1, 1984

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By Alan R. Johnson

Because of the competitive nature of the iron ore pelletizing industry, commodities required for the production of pellets are continually being scrutinized to minimize their usage and offset rapidly escalating costs. In the Tilden pellet plant, the usage of one commodity, bentonite, has been reduced from over twenty-four pounds per long ton of pellets to as low as eight pounds per long ton. The evolution of bentonite usage from plant start-up to the present time is described.

Jan 1, 1984

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By Emmet K. Oslen

Kaiser Steel Corporation, the pioneer steelmaker on the Pacific Coast, was founded by the late Henry J. Kaiser. In 1944 the Company purchased from the Southern Pacific Railroad an iron ore property 200 miles east of Los Angeles known as Eagle Mountain. Today the domestic operation of Kaiser Steel Corporation consists of the iron mine at Eagle Mountain; two coal mines, one each in Utah and New Mexico; an integrated steelmaking complex at Fontana, California; and several steel fabrication and erection facilities along the west coast. Kaiser Steel also has interest in Hamersley Iron, Ltd., Australia, and Kaiser Resources, Ltd., British Columbia. Eagle Mountain Mine is located about 80 miles east of Palm Springs and adjacent to the southeast corner of Joshua Tree National Monument. The area is one of the most arid in the world averaging only two inches of rain annually. Geologically, the mine is at the western edge of the Basin and Range Province which covers about one-half million square miles of the western United States. The Province is typified by north to northwesterly trending fault block mountain ranges separated by sediment filled valleys, Production has totaled over 82 million tons of finished products since the first shipment in June, 1947. Over 500 million tons of material have been mined from the deposit to date. Eagle Mountain Mine is noted for the pioneering use of the largest and most up to date equipment to mine and process its ore. In 1961 Eagle Mountain received the first fleet of 100-ton haulage trucks in the mining industry. There were thirteen semi-trailer units in the fleet. The first 12 to 17-yard size shovel in the mining industry was placed in operation at Eagle Mountain during 1962. Rotary drilling was introduced at Eagle Mountain in 1954 to replace churn drilling. Eagle Mountain was the first major mine to use metallized slurry when three aluminum slurries were introduced for primary blasting in 1962.

Jan 1, 1972

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By Lewis Gordon, Alan Morrow, Aundra Nix

At the ASARCO Mission Mill, a multivariable, predictive controller was used to optimize parallel grinding circuits, improving throughput and product size. Using a dynamic model of the grinding circuit developed from on-line testing the software manipulates 4 variables to control 14 quality and constraint variables in each circuit. Traditionally, model-based control in grinding is difficult due to ore changes. This is addressed via a novel method to predict mill overload and automatic model switching.

Jan 1, 2000

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010