Search Documents

By D. F. Watson, G. M. Philip

The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write: "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accumulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common.

Jan 1, 1988

By L. G. Austin

A program has been written to combine the Klimpel-Austin approximate model for liberation in a binary system with a mill model applicable to ball milling. The model applies for a system where the volume fraction of valuable B in host matrix A is small. The mill model is treated as an equivalent series of fully-mixed reactors. Twenty-three classes of material are considered: pure A; pure B; unchanged AB; 0-10.2 B in AB either as surfac- exposed B or as wholly-contained grains of B; 10-20% B in AB, surface-exposed or wholly- contained;etc.. to 90-100% /b ub /ABm syrface-exposed or wholly-contained. Illustrative cases are given making reasonable assumptions concerning relative rates of breakage and primary breakage distribution functions for each class of material.

Jan 1, 1986

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By I. Iwasaki

The effects of percent solids, mill loading and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of minus 325 mesh - material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition.

Jan 1, 1984

By J. J. Moore

Combustion synthesis or self propagating high temperature synthesis (SHS) reaction systems are discussed with respect to thermodynamics and kinetics. In particular, tile effect of the process parameters, ego particle size, AHf, ignition and combustion temperatures on these self sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall activation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti -X intermetallic shape memory alloys, TiC-Al2O3 and ZrB2 ?Al2O3 ceramic composite materials.

Jan 1, 1991

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

The Mesquite mine is being operated by Gold Fields Operating Co.-Mesquite, a subsidiary of Gold Fields Mining Corp. The mine Is located in southeastern California about 56 km (35 miles) east of the farming community of Brawley, California. The mine has been in commercial production since early 1986 and Is a conventional open pit mine developed on 6.1 m (20 foot) benches. The gold is recovered by heap leach using permanent heaps built in multiple 6.1 m (20 foot) lifts. This year's gold production will be in the range of 5,600 kg (180,000 troy ounces). Current ore production is about 18,140 tonnes (20,000 tons) per day while the total tons mined Is averaging 65,000 tonnes (72,000 tons) per day. The climate at the mine is extremely arid with rainfall of 7.6 cm (3 inches) per year. From early May until late October daytime temperatures generally exceed 37.8 degrees Celsius (100 degrees Fahrenheit) and can be as high as 37.9 degrees Celsius (120 degrees Fahrenheit).

Jan 1, 1989

By J. C. Motz

With ore grades continually decreasing and finer mill feed requirements, it becomes increasingly important to have the capability to handle the larger tonnages economically. With the 10 ft. Standard capable of reducing 1,633 metric tons per hour (1,800 short tons per hour) to 80 percent passing 50 MM (2 inches) and the 10 ft. Short Head following to produce a mill feed of all minus 12 MM (1/2 inch) at a rate of 608 metric tons per hour (670 short tons per hour), we feel significant savings will be realized in installation and operating costs. The largest concentration of cost in the secondary and tertiary crushing stations is the building itself that houses the process equipment. An example of the savings to be attained can be seen from an examination of a 40,820 metric ton (45,000 short ton) per day crushing plant. A total of nine 7 ft. Symons Cone crushers is used to generate 12 MM (1/2 inch) ball mill feed. The average center distance between units is 6.1 M (20 feet) and allowing a 6.1 M (20 feet) nominal distance from the centerline to the wails, the building becomes 61 M (200 feet) long. For this production rate, four 10 ft. Symons Cone crushers would be required. With the 10 ft. crushing plant requiring a center distance spacing of 7.6 M (25 feet), the building length totals approximately 38 M (125 feet). Construction costs vary depending on location, but a reduction in building length from 61 M (200 feet) to 38 M (125 feet) will result in estimated savings of between $2,500,000 and S4,000,000. While the 10 ft. Symons Cone has been involved in a number of feasibility studies for some time, the Process Machinery Division of Rexnord commenced detail design work on the 10 ft. Cone crusher in 1972. For comparison purposes, the 10 ft. and 7 ft. capacities are given in Table 1.

Jan 1, 1978

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By J. F. Strunk Jr., K. M. Maestas, Y. Chai, R. Legrand, R. L. Henry

"Groundwater with elevated sulfate and metals was treated using a sulfate-reducing pilot PRB consisting of a series of six 55-gallon drums filled with ZVI (Fe0), wood chips, brewer’s grain, limestone, and emulsified vegetable oil (EVO). Sulfate was reduced from >3000 to <250 mg/L and Cd, Cu, Mn, Ni, and Zn concentrations declined up to 3 orders of magnitude in 2 months. After 6 months of operation at a 7.5-day retention time, sulfate broke through. The system was then rejuvenated by injecting EVO in each drum and operated for 5 more months at a 9-day retention time. Sulfate-reducing bacteria in the pilot system grew by 3 to 4 orders of magnitude in 2 months. Some cementation of the PRB media was observed in the first 2 drums after processing 25 pore volumes of water, due to preferential upstream precipitation of sulfides; this can be avoided through operational modifications. Resulting permeability losses were estimated at 0.1% to 1% per year. Absorption/desorption was tested at bench scale to evaluate the use of various oil-soaked sorbents as a slow-release source of dissolved carbon. The tests show that oil sorbents can increase the useful life of a PRB between oil refills to over 100 pore volumes. INTRODUCTION High sulfate concentrations, low pH, and dissolved metal exceedances are common characteristics of mining-influenced water (MIW). Above-ground such MIW is commonly treated using biochemical reactors (BCR). In a BCR, water generally flows vertically downward through a layer of biomass, such as wood chips, manure, etc. The dissolved organics resulting from the decay of this material are oxidized first by microbes using oxygen; when oxygen is exhausted, other bacteria can use nitrate, and then sulfate to oxidize organics. Sulfate-reducing bacteria (SRB) reduce sulfate to sulfide, which quickly reacts with metals to form largely insoluble and stable metal sulfides. These reactions can be summarized as follows:"

Jan 1, 2016

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By J. F. T. Agapito

Stability in Exxon&apos;s Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985