Search Documents

By D. Naden

Sulphuric acid leaching is the most common method of recovering uranium from its ores and in the following discussion various alternative low cost routes are investigated for recovering uranium from milled ore acid leach liquors. Historically uranium has been recovered from dilute impure leach liquors by packed bed ion exchange (IX), solvent extraction (SX) or a combination of both. All three process routes as commonly practised require complete separation of leached solids and liquids, as well as extensive solids washing in order to reduce soluble uranium losses to a minimum. Separation and washing are costly and often require equipment covering large areas of land. The size and capital cost of the post leach solids washing operation is controlled by the ease of washing the slimes fraction of the ore and the key to the problem of cost reduction, as many others have realised, lies in the ability to separate the slimes fraction of the ore from the more easily washed sands, to wash the sands in low cost equipment and to recover uranium from the slimes stream. Sands and slimes are usually defined in this context as the material larger than, and smaller than, 325 mesh (44 microns). The proposed flowsheets which minimise solid-liquid separation and washing have usually incorporated ion exchange (Refs 1,2,3), and resin in pulp is in fact practised in several mills in the USA (Ref 1). The resins used in these flowsheets and [cranium] recovery throughout the world have been strong base resins which load rapidly and are moderately selective for the uranyl sulphate complex anion over the range of pH which is conveniently achieved in an acid leach operation. Strong base resins are, however, not as selective as weak base resins and weak base liquid reagents owing to the adsorption of competing anions, some of which find their way into the product while others act as resins poisons. Ion exchange using strong base resins must therefore be followed by a more selective weak base SX purification step if pure yellow cake is required.

Jan 1, 1976

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975

By H. Kellerwessel

This paper refers to the new crushing and grinding process, which was invented by Professor Schönert (Ref.1), Clausthal, Germy (author of one of the papers presented at this meeting). The process is known as high pressure particle bed comminution or interparticle crushing. Several papers by Professor Schonert and his coworkers and by specialists of the companies producing the necessary equipment under license agreements already described fundamentals of the process, the equipment used, results of lab size and large scale tests and finally the first results of truly commercial operations (Ref .2 to 11). Therefore it should be sufficient to summarize the main facts here: - To a bed of bulk material a pressure of more than 50 MPa is applied. Comminution is achieved mainly by the pressure which one particle transfers to the other and not by squeezing single particles between the working surfaces of some crusher or grinding media.

Jan 1, 1987

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By D. S. Bubar

This presentation will represent a diversion from the central theme of Cordilleran geology, in both time and space, as we move 2,000 miles east of Spokane to eastern Canada, specifically the province of Quebec, to discuss a major new Archean-age volcanogenic massive sulphide deposit called Louvicourt. The deposit is located in the Val d'Or camp in the prolific Abitibi Greenstone Belt some 400 miles north of Montreal. It was discovered by Aur Resources in June, 1989 on a property operated under the terms of a joint venture with Louvem Mining, a Quebec company controlled by Ste. Genevieve Resources Inc. of Montreal. As a geologist, I am proud to be able to describe Louvicourt as a geological discovery, as it was found by doing systematic deep diamond drilling based on a geological concept. The deposit is essentially blind from surface and lay undiscovered for the 10 years that the Louvem mine was in production just 2,000 feet away from its easternmost workings.

Jan 1, 1991

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Wallace Macgregor

The direct investment role of Middle Eastern oil producing countries in future world-wide mineral development probably will be a limited one for the next five years. Their needs and their longer range economic objectives substantially preclude any such risk taking ventures. There is, of course, the possibility of political in- vestment. One hears many rumors and doomsday calculations of what the Arabs might do with the rising accumulation of surplus funds. Up to now, this kind of investment has been more in rhetoric than in money. For the most part, oil producing countries of the Middle East have been, and will be, investing surplus funds with strong emphasis on the preservation of capital. They will seek security first and yield second just like any other prudent investor. In several respects, this is regrettable. A direct infusion of risk capital into mineral development, especially in the Third World countries, is a constructive way of enhancing their earning power which many desperately need just to stave off starvation. It would also be a good way of eliminating material shortages in the industrialized world. Most important of all, it would help to ultimately reduce inflation without imposing the hardship of recession. So why isn't it done?

Jan 1, 1975

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By N. B. Aughenbaugh

The People's Republic of China has 582 Gt (641 billion tons) of proven coal reserves. At present, 576.5 Mt (635.5 million tons) of coal are mined a year which makes China the third largest producer of coal in the world. Underground mining accounts for 95% of the total production. This paper will discuss the coal districts, coal types, jurisdiction of coal mining, and methods of underground mining. The article also will outline China's objectives in future planning and development of its coal reserves.

Jan 1, 1982

By James B. Lincoln

The Schaffer linear kimberlite complex and Aultman kimberlite diatremes comprise a major part of the State Line kimberlite district of Colorado and Wyoming, which encompasses approximately 200 sq mi (500 km2). The district is located along the eastern flank of the northern Front Range and is underlain prin- cipally by Precambrian granites (approx. 1.4 b.y.) which have been intruded into an older (approx. 1.75 b.y.) metamorphic complex. The kimberlite occurrences are Devonian in age and are related to older Precambrian linear structures. The Schaffer kimberlite complex is a dike or fissure system with enlargements or blows developed at the intersections of cross faults; the two Aultman occurrences are diatremes. Kimberlite within the Schaffer complex is predominately grey to green phlogopite-calcite kimberlite breccia and tuffisitic breccia. Carbonate is abundant in some phases. Inclusions of host granite are common and locally abundant. Upper mantle peridotite, pyroxenite, and eclogite and lower crustal granulite xenoliths are present at many localities. Four phases of tuffisitic kimberlite breccia occur in the Aultman diatremes. These breccias are characterized by high carbonate and serpentine contents. Xenoliths of upper crustal granite, lower crustal granulite, and upper mantle assemblages are abundant locally. Lower Paleozoic sedimentary rock xenoliths are also abundant in the Aultman diatremes but are absent in kimberlite of the Schaffer complex. From 1979 through September 1982, Cominco American, Inc., conducted geologic mapping, petrographic studies, geophysical surveys, geochemical surveys, and auger drilling in the Schaffer-Aultman project area as part of an extensive evaluation program of kimberlite occurrences. Forty bulk samples (approx. 8,000 metric tons) were excavated from the occurrences and then were processed for diamonds at Cominco American's heavy media separation and diamond recovery test plant at Fort Collins, Colorado. Indicated grades from the Schaffer and Aultman kimberlites range from approximately 0.5-1.0 carat per 100 metric tons and as such, the occurrences do not appear to approach economic viability at this time.

Jan 1, 2013

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By M. Deniz Turan, HASAN NIZAMOGLU, Z. ABIDIN SARI, Tolga Depci

Chalcopyrite extraction in an aqueous acid medium occurs through solid transformations into distinct intermediaries. As intermediates, mineral phases CuS, Cu2 S and Cu5 FeS4 may generate in the leaching solution before CuFeS2 completely decomposes to Cu2+, Fe2+ and S0. Oxalic acid is a common organic acid, and it dissolves easily in warm water. Due to the chelating feature of oxalic acid, it hinders iron precipitation by composing soluble complex anions in a wide range of pH. In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using hydrochloric acid (HCl). Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp= 4.43 × 10 −10) was performed by conventional leaching in the presence of HCl.

By Terrence R. Lejcher

Strip mining has played a key role in the production of coal used to produce energy in this country. About 56 percent of the 1.3 x 106 hectares (3.2 x 106 acres) that had been disturbed by surface mining as of 1965 can be attributed to stripping (Udall, 1967). The runoff from these stripped areas is usually heavily polluted with high concentrations of total dissolved solids, iron, aluminum, manganese, sulfates, and has low pH values with high acidity. Another problem of a most serious nature in our large cities is the volume of treated solids to be disposed of after sewage treatment. Chicago is presently producing about 664 metric tons/day of dry weight solids (Horn and Earles, 1968). Disposal methods most commonly used include lagooning, incineration, and landfilling. The high cost of land in an urban community is prohibitive of lagoon storage. Incineration and landfill disposal create air and water pollution problems. Many countries including Australia, England and Israel have long realized the value of sewage solids if they are recycled back to the land. In the United States, the value of such solids in reclaiming strip mined land has been recognized by relatively few people. This paper is concerned with the use of anaerobically digested sludge to reclaim strip mined land.

Jan 1, 1972

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By Orris C. Herfindahl

Every few years we are treated to a battle over trade policy when the Reciprocal Trade Agreements Act comes up for consideration. In 1962 it is especially appropriate to consider the problem of mineral import -policy and the closely related problem of general import policy, for this year's struggle is different from those of the past in two ways. First, proposals have been made which are a substantial departure from past trade agreements legislation, and second, the formation and growth of the Europe Economic is Community may have an important bearing on the kind of legislation that is adopted. But this anticipates what is to come later. My task is to examine the problem of mineral import policy, although we shall find soon enough that general trade policy must be considered in order to get an indication of what is in store for minerals.

Jan 1, 1962

By S. L. Crouch

The general term "coal mine burp" refers to the sudden and violent failure of in situ coal. Coal bumps occur in most countries where coal is worked by underground methods, and are related to both geological factors and mining tech¬niques. Although no single set of circumstances is solely responsible for causing coal bumps, it is generally agreed that at least one of five conditions is necessary in order for then to occur: 1,2,3,4 (1) the depth of cover exceeds 500-ft., (2) the overlying strata are relatively strong and stiff, (3) the coal is structurally strong, (4) the floor does not heave readily, and (5) the mining method produces high stresses over a large area of the seam. Except for the last, these conditions relate to geological factors that are impractical to control. Consequently, methods of controlling or minimizing the occurrence of coal bumps usually are concerned with mining techniques. Coal bumps have been successfully controlled by both longwall and 'yielding pillar' mining systems 4. The longwall system is particularly effective in controlling bumps, but does not eliminate them completely, especially in strong coal seams being worked at comparatively great depths, say in excess of 2000-ft.5. Under such conditions, auger drilling or water infusion often prove helpful 5,6. These techniques are used to destress or otherwise alter the mechanical properties of the coal in an attempt to shift the peak "abutment pressure" away from the immediate vicinity of the face. Under 'normal' conditions, however, it can be expected that the coal near the face will be crushed under the prevailing high stress conditions and that the peak abutment pressure will automatically be shifted into the solid coal. In this context, coal mine bumps can be characterized as unstable releases of energy associated with successive yielding of portions of the coal seam with progressive mining. Longwall and yielding pillar mining systems are effective in controlling coal bumps because they ordinarily do not allow the zone of peak abutment pressure to become 'surrounded' by destressed coal.

Jan 1, 1973