Search Documents

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By D. J. Frey

While costs of most commodities and services have increased markedly over the past 25 years, the cost of electricity has steadily declined. One of the reasons for this price decline is the improved efficiencies of generating plants which is shown in Fig. 1. 1,2 Another reason for this is the decline in coal production costs. Efficiencies for the best plant increased from about 32 percent in 1540 to about 40 percent in 1962 and then decreased slightly to 38 percent in 1965. The increase in efficiency for all plants (US average) has been even more notable, progressing from less than 15 percent in 1940 to about 32 percent in 1965. The chief reason for the improved efficiency is the change in operating steam temperatures. These increased about 12 F per year until 1200 F was reached in 1962. At this high temperature excessive corrosion of super-heater and reheater tubes was experienced and steam temperatures were dropped back to 1050 F and even 1000 F in some cases. To successfully compete against other energy sources for generating electricity, this corrosion problem must be solved so that operation at higher temperatures and thus, increased efficiencies will be possible.

Jan 1, 1967

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By Warren G. Burres

or more than 50 years the Portland Cement Association has represented the United States cement industry in matters relating to the technology and use of cement and concrete. Interestingly enough, PCA?s emphasis has been on concrete and its uses rather than on Portland cement. The cement industry realized long ago that cement is basic and serves its fundamental purpose as an ingredient in concrete. Cement could never be successful if concrete were not. Work with the users and specifiers of concrete had to be done at its end point of application--in a building, bridge, dam, highway or home. PCA, over its half century of existence, has been dedicated to this job. I should like to talk to you today on the less technical side of concrete--what it has been--what it is today--and what it can offer in future construction. Concrete, in many forms, has a long background extending from such notable historic times as the Roman Empire. Here, concrete made from pozzolanic cement from the slopes of Mt. Vesuvius was used to construct the Coliseum, home of the Roman circus; for the Appian Way, the ancient forerunner of the Interstate system; and the miles of aqueducts throughout Europe, many of which still carry water. In 1811 Joseph Asppin, an English bricklayer, made the first modern cement by the artificial mixing of pulverized limestone and clay materials. Ht,

Jan 1, 1971

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on operating and design variables such as air and slurry flow rates, underflow and overflow opening areas, percent solids of the feed, reagent levels, particle size and ASH length. Time-averaged multiphase flow characteristics, as determined by X-ray CT (described in a previous publication), are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2in. diam. air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response, which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1996

By Ora H. Rostad

Some gold production was obtained from placer deposits in Puerto Rico during the period of Spanish colonial rule, but most of the gold was produced prior to 1536. There had been no significant hard rock mining, other than in quarries for road metal or construction purposes or for raw materials to make cement, prior to 1954 when the government of the Commonwealth of Puerto Rico recognized that changes in the mining code were necessary to stimulate exploration for metalliferous ore deposits. The Puerto Rican Legislature passed an act (No. 6), which was approved on Oct. 6, 1954, that reiterated that the title to all "commercial minerals" is vested in the Commonwealth of Puerto Rico. The act provided for the establishment of a Mining Commission, stipulated the power% with which the Mining Commission was vested, and provided that no one may dispose of "commercial minerals" in Puerto Rico without a Commonwealth grant issued on its behalf by the Mining Commission. Act No. 6 also provided for prospecting permits, mining leases, and grants. The Mining Commission, by authority granted to it by Act No. 6, adopted regulations effective Nov. 21, 1957, relating to prospecting, leasing, and producing commercial minerals in Puerto Rico. Royalty rates were also specified for various types of deposits at different annual tonnage production levels.

Jan 1, 1991

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By W. B. Beerbower

Resin bolting has enjoyed wide acceptance for coal mine roof support. Beginning in 1973, the first year of significant resin bolting in coal mines, we estimate that 2.5MM resin bolts were installed. This grew to 7MM resin bolts in 1974 and 13MM in 1975. Resin bolts are currently being used in over 300 coal mines throughout the major coal producing areas of the U.S. and barring major work stoppage we expect more than 17MM will be installed in 1976. Although not a cure-all, the number of unintentional roof falls occurring in many mines has been dramatically reduced as a result of converting to this "new" method of support. 1 The improved anchorage strength of resin bolts provides better roof support. (Slide #1) This anchorage strength provides a mechanism to resist changing roof stresses along the entire length of the fully grouted resin bolt, thereby assuring stabilization of rock strata over long periods of time. The ability to resist roof displacement is borne out by readings obtained from strain gauged bolts. These findings can be summarized as follows.2

Jan 1, 1977

"The mining industry suffers from a number of incorrect perceptions, one of which is that it is an outdated industry that has not changed for hundreds of years. But the truth of the matter is that mining is a vibrant, highly complex industry that not only employs highly skilled and educated professionals but is also often on the cutting edge of technology. It is an industry with projects that are ever-evolving and among the most challenging engineering feats in the world.Take for instance the U.S. 53 Highway Relocation project in Virginia, MN. While more of a civil engineering job than a traditional mining project, it is still a complex engineering challenge taking place in a mining environment that has called on the skills of eight state agencies, three federal agencies, a host of contractors and many consultants, including many from the local mining industry in the Iron Range of Minnesota.In 1960, the Minnesota Department of Transportation (MnDOT) constructed U.S, Highway 53 on a private easement owned by US Steel that cut across a massive taconite deposit. MnDOT constructed the highway with the agreement that if the highway needed to be moved to access the taconite deposit before 1987, US Steel would foot the bill. And if the move was required after 1987, the responsibility would fall to MnDOT. In 2010, MnDOT received the notice that the highway would have to move as property owner United Taconite planned to access the ore, setting in motion one of the greatest engineering challenges, and the highest risk project, in the history of the states’ transportation department.Pat Huston, U.S. Highway 53 Relocation project manager, opened the 90th SME Minnesota Section Conference in Duluth, MN on April 19 with a presentation about the project that includes 5 km (3.2 miles) of fourlane highway and a new 345-m (1,132-ft) bridge that will be the tallest in Minnesota when it is completed later this year.“This project was not business as usual,” Huston told the packed crowd. “Highway 53 connects Canada and the Iron Range to Duluth and Lake Superior. It is an important highway.”During his presentation he spoke about many topics that were familiar to the more than 1,100 mining professionals who attended the conference. In his keynote speech,"

Jan 6, 2017

By B. Mishra, K. Savage, T. Evans, A. Noble

"Recent government initiatives and commercial activities have targeted asteroids for in-situ characterization, manipulation, and possible resource extraction. Though emergent technologies may be effective for such undertakings, uncertainties remain concerning the effects a space environment may have on the mechanical behavior of rocks. Various non-destructive rock characterization techniques can empirically predict in-situ rock strength on Earth; however, these techniques must be adapted to account for unique space conditions. In order to mimic one element of a space environment, various rock samples were evaluated after prolonged exposure to low temperatures ranging from -75°C to 0°C. Tests included uniaxial compressive strength, Schmidt hammer, and ultrasonic pulse velocity, while rock types included shale, limestone, and chalk. This data was used to generate a temperature correction for the non-destructive methods and evaluate the accuracy of these methods in predicting strength values. Overall, these results provide insight on the mechanical behavior of rocks at low temperatures and may be used to design robust systems needed for asteroid rock characterization INTRODUCTION NASA and various commercial entities have recently targeted near-Earth asteroids for exploration and scientific investigation to better understand their in-situ properties, mechanical characteristics, and formative processes. In particular, NASA’s Asteroid Initiative encompasses several studies and mission plans that will enable future investigations while vetting technologies that can be applied to deep space exploration. One component of the Asteroid Initiative is the Asteroid Redirect Mission (ARM). This multi-stage space mission proposes to rendezvous a robotic spacecraft with a large near-Earth asteroid. Upon approach and after landing, the spacecraft will prospect the surface and identify a multi-ton boulder (up to 5 m in its largest dimension) suitable for capture. The robotic spacecraft will engage the boulder, remove it from the parent asteroid, and return the sample to a controlled lunar orbit. Once the asteroid mass is in stable orbit around the moon, astronauts aboard the Orion spacecraft will engage with the retrieved asteroid for manned exploration that will include sample collection and geologic prospecting. Launch plans for the ARM robotic craft are expected as early as 2020, and manned explorations of the asteroid mass in lunar orbit are expected to follow sometime in the mid-2020s (NASA, 2015). Overall this mission will demonstrate NASA’s ability to intersect, manipulate, and redirect an extraterrestrial body, while supplying scientific information that is relevant for planetary defense and in-situ resource utilization (ISRU) applications."

Jan 1, 2016

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By J. A. Herbst, Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous grinding mills through detailed mathematical models, a better understanding of the charge motion and rocklball segregation is needed. To achieve this a 0.61 m (2.0 ft) diam by 0.305m (1 .0ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video presentation (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rocksize distribution, and flow rates.

Jan 1, 1990