Search Documents

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis, and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behaviour during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behaviour of an ore in a concentrator, pilot plant or bench test; and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1991

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By D. Akers

Many of the trace elements found in coal are associated with mineral matter, making it possible to remove them by physical coal cleaning. As part of work funded by the Electric Power Research Institute, both conventional and advanced coal cleaning processes were found to provide large reductions in the concentration of many trace elements that, if released into the atmosphere, are considered to be potentially toxic or environmentally harmful. Advanced physical cleaning technologies appear to provide greater reductions than conventional technologies. Chemical cleaning processes may also remove many trace elements, possibly including organically-bound elements such as beryllium. Care must be taken in the disposal of coal cleaning plant refuse because oxidation and leaching of this material can create highly acidic leachate and many trace elements are mobile in an acid environment. Laboratory leaching procedures are potentially useful in determining the degree of risk of water contamination by trace elements should an acid environment form.

Jan 1, 1992

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By VIVEK KUMAR HIMANSHU, PK SINGH, AK MISHRA, MP ROY, RAVI SHANKAR

Underground blasting has many challenges. The primary aim of blast designers is to optimize drilling and blasting parameters to deal with the associated challenges. Optimizing these parameters is currently based on various rules of thumb, which have many site-specific limitations. Accordingly, computation of these parameters using empirical rock fragmentation predictors can be useful for blast designers. This paper presents the results of work on burden-spacing determination by back-calculation from the empirical Kuz-Ram model for underground stope ring blasting.

By P. B. Queneau, J. E. Litz, T. P. McNulty

I. INTRODUCTION Modern hydrometallurgy has its roots in such notable successes as heap leaching for recovery of copper, cyanidation of gold ores, the Bayer process, the Oxland process for tungsten, electrorefining of copper, roast/ leach/electrowin process for zinc, and production of yellowcake from lowgrade uranium ores. Metallurgical testing techniques, sampling and analytical procedures, operating and maintenance practices, and improved methods and materials of construction which were pioneered in these processes have promoted the extension of hydrometallurgy into other applications. Periodically, new tools such as solvent extraction, resin ion exchange, and flocculants have opened new avenues to hydrometallurgists. Conversely, pursuit of more complex mineralization, the rising costs of energy and environmental quality preservation, and declining ore grades continue to create new challenges. For much of this century, it can be fairly said that practically any hydrometallurgical development moved the frontier of technology. The 1970's and 1980fs, however, have seen a significant maturing of hydrometallurgy's role in process metallurgy. Simplistically, this maturing seems to derive from a growing awareness of the strengths and weaknesses of hydrometallurgy and a determined effort to capitalize on the strengths. For example, many of us were among those revolutionaries of the 1960's and 1970's who taught that "chemical smelting" was the answer to the treatment of all sulfides. We now recognize, however, that only in very special cases can hydrometallurgy offer economic advantage over the generally less energy-intensive pyrometallurgical systems. The maturing of hydrometallurgy does not, however, signal stagnation. Important innovations are being studied and developed in most extractive areas, and a number are approaching or have achieved commercialization. From our company's perspective, that of an organization dealing with the development of the most economic solutions to metallurgical problems, innovation must be defined as the commercially successful reduction of an idea to practice. There appears to be no shortage of ideas, nor has there ever been a shortage. Many ideas now being implemented were conceived decades ago, but reduction to practice was foiled by the lack of such technology as responsive process control and economical materials of construction capable of withstanding highly corrosive or erosive environments. Commercialization of a new process is a particularly challenging undertaking. Even if technical risks are reduced to a minimum through careful and thoughtful process development, there are inevitable uncertainties in feed characteristics, variable costs, and product prices. Commercialization takes courage, both on the part of innovators who may be staking their careers or reputations and of investors who may face financial disaster in the event of project failure. This paper discusses innovative programs and recently commercialized processes which either have been discussed in the literature or disclosed to Hazen Research staff in private nonconfidential conversations with contacts in industry. Regarding this latter category of information, relative ease of communication has resulted in many of our observations being of North American origin.

Jan 1, 1985

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By Robert E. Haun

Retech's Plasma Arc Centrifugal Treatment (PACT) system is a thermal technology that uses heat generated by a plasma torch to treat hazardous waste containing metals and/or organics. Metal bearing solids and soil are melted by the process, and organic contaminants are thermally destroyed. The molten material forms a hard, glass-like leach resistant mass after cooling in a mold. This paper discusses plasma processing in general and presents some results of treating mineral processing wastes using the plasma arc centrifugal treatment process.

Jan 1, 1995

By R. M. Hays

Jan 1, 1980

By John S. Livermore

I feel very privileged to be added to the distinguished group that has received this award since the first recipient, Reno Sales, received it in 1954. If my research is correct, the last geologist to be honored was Bill Callahan in 1982. Perhaps the Awards Committee decided it was about time to select a geologist, and I became the beneficiary. Regarding the discovery of the Carlin ore body, it was the culmination of several studies - one going back as far as 1939 when a US Bureau of Mines engineer named W.O. Vanderberg recognized an unusual type of gold mineralization in sediments in northern Nevada. What was unusual was the fact that the gold was so fine that it would not concentrate in a pan. This, plus the study of the Roberts Mountain thrust by Ralph Roberts (1960) and conversations with Harry Bishop, manager of the Gold Acres Mine, pointed Alan Coope and me in the direction of the Lynn Window and, eventually, the Carlin discovery. There has been a great deal written about this discovery. I thought it would be interesting to discuss the evolution of Carlin gold exploration in Nevada since this time and to discuss the changes in perception of this unique type of mineralization. The method used by Coope and me in following up on Roberts' work was to map geologically the Roberts Mountain thrust and conduct geochemical sampling of favorable outcrops and float. Coope was highly experienced in geochemical exploration, as he had graduated from the Royal School of Mines in London, studying under John S. Webb, one of the pioneers of geochemistry as applied to mineral exploration. We first considered using pathfinder elements, but finally concentrated on gold analyses alone, even though the sensitivity of fire assays used at that time was only about one-half part per million. According to the spatial relationship of the mineralization to the Roberts Mountain thrust, as pointed out by Roberts (1960), we were looking for mineralization within the thrust itself. Our models were the known Gold Acres and Getchell mines, which contained reserves on the order of 0.9 to 1.8 mt (1 to 2 million st). These were not of substantial size, but I had hoped we might find more than one of these tributary to a mill that would justify an operation for our employer, Newmont Mining Corp. What we ended up with was the type of deposit we were looking for - an open pit deposit of micron gold, which the old timers had missed because the gold was not capable of being panned. But never in our wildest dreams did we think there was a chance of finding a body containing 10 mt (11 million st) of ore at 0.30 oz/st (10.3 g/t).The deposit was not in the thrust proper but was found in a favorable horizon of Roberts Mountain siltstone that was below the thrust. This is the first example of how a model should not be followed blindly. Newmont was successful in keeping this discovery quiet for some time. After a considerable amount of drilling, a rumor circulated that they had discovered a large low-grade ore body of around 1.7 to 2.1 g/t (0.05 to 0.06 oz/st), which of course would not have been economic with gold at $1.13/g ($35/oz), which was the fixed price at that time. The company, for obvious reasons, did not discourage the rumor. When, however, the true results came out there was a lot of feverish activity. Because of this new type of so-called "invisible gold," which could have been missed by the old timers, the thought was that other deposits would be discovered very soon. The Carlin and other smaller deposits, including Bootstrap, Blue Star and Gold Quarry, were in windows where the lower plate of the Roberts Mountain formation (below the thrust) had been exposed by erosion. This then became the new

Jan 1, 1997

By Jean Dupere

Mr. Chairman, Ladies and Gentlemen, I'd like to take just a moment of your time before we examine the current position of the asbestos industry and its market outlook to take a searching look at the product itself. I feel that if we are to understand the problems that beset this basic mining and manufacturing industry and, more important, if we are to appreciate the solutions to these problems that I plan to put forward in a few moments' time, then we had better look at asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. This has resulted in asbestos finding its way - in fact, being welcomed - into literally hundreds of applications.

Jan 1, 1984

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized using waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empirical testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicate that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate than conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

By M. B. Haggerty, Joe Welna

The Minnesota Department of Transportation is constructing a stormwater storage facility (SSF) along Interstate 35W (I35W) south of downtown Minneapolis, MN. The project will provide storm surge capacity reducing the frequency with which major precipitation events result in flooding of I35W. The design consists of six, 42-foot diameter, 90-foot deep, adjacent underground shafts providing 14.7-acre feet of storage. Construction challenges include high groundwater with variable glacial outwash deposits. Constructability and ground variability were managed using construction manager general contractor (CMGC) project delivery. CMGC provides an environment for collaboration and innovation starting in the design phase and carrying through construction. This paper provides an overview of key efficiencies and collaboration examples implemented on the I35WSSF project which were aided by CMGC delivery.

Jun 13, 2023

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of Humanitarian Engineering (HE) in 2020. HE is a socio-technical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (10, 18). By focusing on sustainable development, community engagement, and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts, and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency.

Feb 1, 2025