Search Documents

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By George E. Summers

A salt dome appears to provide the basic medium requirements for the excavation of the 315 foot diameter, unsupported spherical cavity at a depth of 2700 feet required by the AEC in a proposed "decoupling" experiment. Tatum Salt Dome was a natural choice for a site because more geological and hydrological information has been accumulated on Tatum than any other salt dome on the Gulf Coast. The Tatum Dome is a mile in diameter, roughly flat topped, nearly cylindrical in shape and has some overhang at the top. The salt stock has nearly vertical layering of alternating bands of salt and anhydrite. In the vicinity of the dome, adequate fresh water for solution mining is available in surface streams and in subsurface aquifers. A saline aquifer is available for brine disposal. A tentative cavity location was selected near the center of the dome which meets the design criteria established by the AEC.

Jan 1, 1968

By Roger C. Wilmoth

The most common method of treating mine drainage to prevent water pollution consists of neutralization and aeration. This process removes the acidity, iron, aluminum, and some other heavy metals, but does not render a water suitable for domestic or industrial use because of the high dissolved solids, hardness, and sulfate in the treated water. The Environmental Protection Agency (EPA), has been sponsoring and conducting research since 1966 on the use of reverse osmosis (R.O.) for the treatment of mine drainage. This process has been found to be highly effective in the removal of nearly all the dissolved solids. In addition, since R.O. is a concentrating process, potentials for recovery of valuable heavy metals are possible. This paper is a review of the state-of-the-art on the treatment of mine drainage by reverse osmosis.

Jan 1, 1972

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By J. F. Hunt

[THE AUTHOR DESCRIBES THE ACTUAL PROCESSING OF THE GOVERNMENT STOCK¬PILE OF CHROMIFEROUS SANDS. LOCATED AT COQUILLE. OREGON, DURING 1955 AND 1956. A GENERAL HISTORY OF THE STOCKPILE IS GIVEN, ALONG WITH A BACKGROUND OF THE GEOLOGY AND ORIGIN OF THESE SANDS. THE FLOW SHEET USED IN THIS OPERAT ION IS OUTLINED IN DETAIL, AND THE MINERALS WON FROM THE STOCKPILE BY HIGH TENSION AND MAGNETIC PROCESSING ARE DISCUSSED AS TO THEIR PURITY AND SALEABILITY. AMONG THESE MINERALS ARE CHROMITE, ILMENITE, MAGNETITE, ZIRCON, GARNET, RUTILE, MONAZITE, GOLD, AND PLATINUM. PLANNED POST-STOCKPILE OPERATIONS ON THE PRESENT BEACH DEPOSITS ARE DISCUSSED. THESE OPERATIONS WOULD HAVE BEEN CARRIEDOUT TO SET UP A' CONTINUOUS INTEGRATED MINING AND BENEFICIATION PROJECT, EXCEPT FOR UNFORESEEN CIRCUMSTANCES WHICH DICTATED THE CLOSING OF THE OPERTIONS AT THE EXHAUSTION OF THE GOVERNMENT STOCKPILE. THE PAPER IS ILLUSTRATED WITH MAPS, FLOW SHEETS, CHARTS; AND PHOTOGRAPHS OF STOCKPILE, PLANT, AND EQUIPMENT.]

Jan 1, 1964

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By W. M. Pytel

A simplified two-dimensional model to analyze time-dependent load distribution and surface subsidence associated with longwall mining geometries is described. The model is based on the theory of beams resting on inelastic foundations and includes visco-elastic behavior of immediate floor strata, non-linear behavior of coal pillars, elastic behavior of face supports, and visco-elastic behavior of the overburden strata. The relative importance of the different variables affecting the performance of longwall mining geometries from ground control point of view is also analyzed. The model has been validated for field observations from one Illinois longwall mine.

Jan 1, 1986

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By H. B. Charmbury

In the United States and in Pennsylvania in particular the coal mine drainage problem is of continuing and growing interest to the coal mining industry, the state government, the federal government and the public at large. The 1965 amendments to Pennsylvania's Clean Streams Law prohibit the discharge of acid mine drainage into the streams of the Commonwealth after January 1, 1967. Because of this new legislation, the coal mining industry and state government are extremely aware of the necessity for new techniques for treatment and prevention of the flow of acid mine drainage from the active mines of the Commonwealth in order to keep the coal mining industry in business in Pennsylvania. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from "active" coal operations and two-thirds comes from "abandoned" mine discharges. As early as 1963 it became evident that the Commonwealth of Pennsylvania and the coal industry in Pennsylvania would have to take active steps to abate the mine drainage pollution of Pennsylvania's streams and rivers. This became quite clear during the deliberations in Harrisburg which climaxed a twenty year struggle for effective strip mining legislation. The bituminous strip mining law enacted that year made it unlawful to have any acid discharge from active stripping operations.

Jan 1, 1968

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

By John Mahoney

We live in a world of change and the mining industry is enjoying some of the most rapid changes today that have been seen in a long time, We'd like you to open your mind to a new concept in material handling. Figure # 1 Shows a new concept combining some of the proven application advantages of the power shovel with which we are all familiar, and applies the advantages of the dragline for the benefit of the user. First, the hydraulic excavator enjoys tooth forces of the shovel because the dipper is attached to the machine with a dipperstick and boom, and can often actually realize greater tooth forces than a shovel because of the prize action of the dipper in hard digging. Second, the hydraulic excavator enjoys the application advantage of the dragline because both the operator and the machine are up above, sitting on top where the operator oversees the excavation and the machine's operating work range is greatly increased.

Jan 1, 1973

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By John T. Atkins

Utah International's Shirley Basin Mine is located in the Southeastern High Plains of Wyoming at an elevation of about 7,100 feet. The Shirley Basin area is a gently rolling semi-arid land. The uranium ore zone occurs at depths ranging from 270 to 350 feet below the surface. Overburden consists of poorly consolidated sandstones, siltstones, and clays. Underground mining was begun in 1960. Conditions were made difficult by high rates of water inflow and ground support problems. The development of a solution mining I or in-situ leaching technique allowed underground operation to be abandoned in 1964. Solution mining provided limited production from 1963 to July 1970. In January, 1969, large scale development of open-pit mining was begun. A 1,200 ton per day mill went "on stream" in March, 1971.

Jan 1, 1973

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By Sean Hunter

Artificial Intelligence has a long history but is currently coming strongly into focus with new advancements. This leads to questions many people are asking: what exactly is AI, how can it be used effectively in mining operations, and what foundation is required to make AI implementations successful? In mining, many AI applications exist, from drill pattern optimization to predictive maintenance. However, many implementations struggle due to data integration challenges. Mining operations generate large amounts of data from many sources, such as fleet management systems, drill sensors, process control systems, and laboratory results. Unfortunately, this data often exists in silos where it’s difficult to get it out, making AI applications unable to leverage it. Worse still, tools that use AI don’t always provide their data back to the system, creating even further data silos. All these problems make it hard to take advantage of the data at the mine, slowing down and reducing the effectiveness of AI. This paper presents a comprehensive approach to organizing mining data using an AI-ready knowledge graph system. We will first explore the evolution of AI in mining, from early expert systems to modern machine learning applications. Then, we will detail how a knowledge graph can integrate business context, operational data, and AI models into a cohesive system that enables more effective AI implementations across mining operations. The proposed method has been developed considering both the unique data challenges faced by the mining industry, while also considering best practices learned from the AI field at large. By following this approach, it’s possible to better utilize existing data, getting higher quality and more complete results faster, and in a way that’s reusable and composable.

Feb 1, 2025