Search Documents

By Tsuneyoshi Funazaki, Takayoshi Nakamura, Keizo Miki, Takashi Imaishi

The underground portion (about 10 km) of Tokyo Wan Aqua-Line consists of eight shield tunnels connected with Kawasaki Man-Made Island in between, at four underground locations. The connection work had to fulfill strict precision and safety requirements in the ground about 60 m below soft seabed, but was completed successfully in May 1997. This report describes the connection work in detail, featuring the method of investigating shield machines’ relative positions, ground freezing method and connection mechanism and procedures. It also mentions the present state of Tokyo Wan Aqua-Line that was put in service on December 18, 1997.

Jan 1, 1999

By R. R. Swanson

Liquid ion exchange is becoming more and more important in hydro-metallurgical processing and recovery of metals. The key to success for this process are reagents which have suitable operating characteristics. One of these important characteristics is a relatively fast phase separation rate in the extraction and stripping circuits, as this greatly affects the size of plant required. A test for measuring phase separation rate is needed to help evaluate liquid ion exchange reagents. Such "a test also would be useful for evaluating carrier solvents that are used for diluting the re-agents. In fact, one standard test method would be very desirable as it would provide a common basis for comparing reagents and sol-vents. The phase separation test described in this paper has been used successfully for several years with the copper reagent, LIX®64N. The test is set up for feed liquors containing low copper concentrations. For other types of systems, modifications in procedure probably would be necessary. However, this test and the associated apparatus could be the basis for a standard phase separation test.

Jan 1, 1972

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999

By W. M. Hart

The current Automatic Data Acquisition system developed by some support manufacturers makes it possible to continuously monitor and record changes in leg pressure and advancing ram stroke in every shield, and shearer position at any moment during the mining operation. In order to effectively use the massive data obtained from this system for improving production and maintenance managements as well as providing better roof control at a longwall face, the research currently conducted jointly by West Virginia University and Cyprus-Amax Coal Co. attempts to develop a Longwall Management System for mine operators. The LMS software package runs on a MS Windows NT environment and consists of four sub-systems: (1) Data Interpretation and Analysis; (2) Production Management; (3) Maintenance Management; and (4) Ground Control. This paper presents the details of each sub-system.

Jan 1, 1995

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By Richard L. Gordon

Coal supply analysis has since about 1973 become a major activity of many scholars and consulting firms. The present paper is an effort to explain in as nontechnical fashion as possible the state of the art and what implications, if any, the research has for those actually engaged in producing coal or regulating the industry. l The discussion stresses the coal supply side of the models and makes limited comments about other elements in the analysis. To orient the appraisal, it is desirable to recall the features of coal supply that an adequate model should capture. The first considerations are the locational aspects of the industry. Transportation costs can, in some cases, exceed the production costs of coal, and thus any adequate model must incorporate a treatment of the economics of transporting coal from one location to another. A second major issue is that of the heterogeneity of coal; models should treat as well as possible such key differences among coals as their Btu and sulfur content. Third, we recognize that, with given technology and labor, capital, and supply costs, an expansion of the supply of a given type of coal in a specific region will occur only if prices rise. This is the familiar proposition of textbook economics that supply is an increasing function of price. Finally, over time, changes in technology, input cost, and depletion interact to cause changes in the price of given amounts of coal. Economics represents the net effect of this process by a shift over time in the supply curve. During the 1950s and 1960s, the trend was to reduce the production costs of a given output; subsequently costs rose sharply.

Jan 1, 1977

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959

By Thad J. Bydlon

Uncertainty of future energy supplies has forced industrial nations to diversify both their energy mix and their energy sources of supply. As a result, U.S. coal exports have grown substantially during the past several years. Projected long-term worldwide economic growth suggests that a well-established trend has been set for increased foreign demand for U.S. coal. As export volumes increase the need for careful planning to prevent bottlenecks and to provide for the uninterrupted flow of coal increases. It also will place increased emphasis on identifying the most economic transportation alternatives. These planning and evaluation functions are greatly facilitated if a systematic method is available for modeling the complex interactions of a coal export system. One such model, developed by the Anaconda Minerals Company, is the Coal Export model.

Jan 1, 1982

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973