Search Documents

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Thomas G. Goonan

Copper production through smelting generates large volumes of material flows. As copper contained in ore becomes copper contained in concentrate to be fed into the smelting process, it leaves behind an altered landscape, sometimes mine waste, and always mill tailings. Copper concentrate, fluxing materials, fuels, oxygen, recyclables, scrap and water are in-puts to the process. Dust (recycled),gases — containing carbon dioxide(CO2) (dissipated) and sulfur dioxide (SO2) (mostly collected, transformed and sold) and slag (discarded or sold) — are among the significant process outputs. This article reports estimates of the flows of these input/output materials for a particular set of smelters studied in some countries. They include Chile (Altonorte, Caletones, Chagres, Chuquicamata, LasVentanas and Potrerillos), Japan(Naoshima, Onahama, Saganoseki,Tamano and Toyo), the United States(Garfield — Fig. 1 — Miami and Hayden) and Europe (Glogow I, Glogow II, Huelva, Norddeutscheand Ronnskar).

Jan 1, 2005

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By H. Ipek

Industrial grinding machines used in the mineral processing industries are mostly of the tumbling mill type. These mills exist in various types: ball, rod, pebble, autogenous, and semi-autogenous. Balls and rods are traditionally media shapes used in the tumbling mills. In resent years, as an alternative to balls, grinding charges with various shapes are being used. Cylpebs are slightly tapered cylindrical grinding charges with length equaling diameter, and all the edges being radiused. Cylpebs of equal diameter and length have 50% greater surface area and 45% greater weight than balls of the same material. In addition, they have 9% higher bulk density than steel balls, or 12% higher bulk density than cast balls. An important advantage of cylpebs over balls is that cylpebs produce narrower granulometric distribution due to their shapes. However, some discrepancies were found in the literature regarding the milling performance of cylpebs in comparison with balls (Chi, 2004). In recent studies, Chi (2004) has provided detailed information on cylpebs and has compared these to balls in relation to media mass, size distribution, surface area, and input specific energy. Ipek (2006) has investigated the effects of cylpebs and balls with equal mass and surface area on the breakage rate of quartz, using cylpebs and balls separately. Similarly, Lameck and Moys (2006) have investigated the effects of balls and worn balls on breakage rate of material using worn balls as grinding environment. However, no study has attempted to investigate the effects of grinding environment other than balls on the brekage distribution. As indicated by Prasher (1987), the breakage distribution function is independent of the following variables in ball mills: hold-up (Mika et al., 1967; Kelsall et al. 1969), mill speed and ball load (Herbst and Fuerstenau, 1972), media load and ball density (Kelsall et al., 1973), mill diameter (Malghan and Fuerstenau, 1976), and powder charge (Shoji et al. 1980). The aim of the present paper is to compare the effects of cylpebs and balls on the breakage distribution function of quartz with respect to same mass and same surface area. BACKGROUND Comminution as a rate process is called kinetic approach. Studies on the kinetic approach are reviewed by Oner (2001). Oner states that grinding kinetics are based on studies by Kolmogorov in 1941 and that Robert (1950) is the first to suggest this approach. Later, Melzak, Loeveday, and Reid have improved the grinding kinetics equation; and, Austin and Lynch have conducted two basic studies on the analytical solutions of these equations. Considering the results of studies comparing the size reduction mechanisms, it has been accepted that breakage constitutes of two operations. These two basic operations, first defined by Epstein (1948), are those of selection of material for breakage and the distribution of breakage material to particle sizes smaller than the initial size (Lynch, 1977). Epstein defined the two operations as: ? Pn(y), the probability of breakage of a particle size in the nth step of the breakage process. ? F(x,y), the cumulative distributions by weight of particles of size x<y arising from the breakage of a unit mass of a size y. Probability of breakage is called a selection or a breakage-rate function (Si). Characteristics size distribution after breakage is called a breakage distribution or appearance function (Bi,j). Due to the difficulties in representing particle size distributions mathematically and constantly, the batch equation based on particle size fraction is suggested. Thus, as is the case in breakage distribution and specific rate of breakage, the breakage parameters were defined by batch grinding experiments conducted in laboratories (Oner, 2001). When effective breakage occurs in the mill, the breakage of material with single feed size fraction usually fits first order grinding kinetics and the specific rate of breakage values can be calculated through the slope of semi-log plot. The values of the breakage distributions are deduced from the size distributions at short grinding times where there is mainly size 1 material breaking and only small amount of smaller sizes to rebreak (Austin et. al., 1984). B values can be calculated by using BII. [ ] where j is the top size of the charge, Pi(t) is the cumulative percent undersize of i th size interval at the short grinding time which gives no more than about 30% broken out of the top size interval. Cumulative primary breakage distribution, Bi,j, is also defined in an empirical form by [ ] where xi is the top size and Bi,j is the weight fraction of primary breakage products. The parameters F, ? and ß define the size distribution of the material being ground. On plotting size versus Bi,j on log scale, the slope of the lower portion of the curve gives the value of ?, the slope of the upper portion of the curve gives the value of ß, and F is the intercept as in Fig.1. [ ]

Jan 1, 2009

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By O. Bernal, G. Velarde

Sociedad Minera Cerro Verde, majority owned by Phelps Dodge produces 200M lbs per year of LME Grade A copper from low cost leaching of secondary sulfides and SXEW processing. Central to the success of Cerro Verde has been the continuous improvement of leaching practices which currently yield over 80% recovery of the contained copper in the ore. This recovery has been achieved by careful attention to operational practices and leaching process fundamentals. This paper details the development of the concept of “Lixiviant Request Rate” where by solution is applied at an optimal rate for the grade, mineralogy, and the point in the leach cycle. Also paramount to the success of Request Rate technology has been the development of irrigation practices such as drip irrigation and irrigation grid design. These developments have ultimately resulted in improved copper production, decreased sulfuric acid and water consumption, decreased pumping cost, and more consistent PLS grades.

Jan 1, 2004

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant&apos; with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005

The US Constitution provides for regulation by the states for protecting the public&apos;s safety, health, and welfare. Hence, in the eyes of the law of all states today, this is the sole justification for registration of professional engineers. Wyoming was the first state to register professional engineers in 1907, to correct abuses of incompetent or fraudulent practices in surveying and real estate. Public safety and health are most directly affected by civil, electrical, and mechanical engineering. Other branches of engineering have a profound effect on the public welfare, including investors, and safety and health of employees. No arguments, pro or con, are valid except in relation to the registration laws of various states. Code of Ethics Few would argue the desirability of requiring conformance with a code of ethics. A major problem lies in enforcing compliance, since protecting the public demands a high standard of competence, yet assessing competence gets confused with restraint of trade. Bidding engineering work on price competition can lead to pressure to cut corners on engineering quality, and was therefore discouraged by codes of ethics. The Supreme Court, in a suit against the National Society of Professional Engineers (NSPE), barred any engineering society from such bidding restriction. It has, however, upheld the right of states to impose codes of acceptable practice as part of registration laws. For example, Texas Canon I reads, "The engineer&apos;s paramount professional responsibility should be the safety, health, and welfare of the general public." Anything less makes the code practically meaningless, but there are potential conflicts of interest in many engineering organizations. How can conflicts be handled? Any corporation could improve its public image by adopting a policy that each employed PE should, without fear of recrimination, record in writing over his seal any problem or flaw in any design that comes to his attention. The policy should further require that his superior provide him a written reply pointing out that the "flaw" is accepted as requiring correction or as a calculated risk, or overruled as erroneous or as a difference of opinion. Errors in calculation of judgment are inevitable. Despite this, there are limits to how much time and money should be spent to eliminate them. It is difficult, however, to see any excuse for failure to conscientiously evaluate the opinion of a PE. This may be an impossible ideal, but how else can the profession or the industry have credibility? The National Council of Engineering Examiners (NCEE) has a code of ethics one presumably subscribes to by signing an application to write a Principles and Practices examination. However, NCEE has none of the power of enforcement that is available through state boards of registration. Registration Qualifications Qualifications are set by the laws of the states. In general, they require passage of an eight-hour examination in fundamentals, preferably at graduation, and, later, one in principles and practices. The examinations are compiled and distributed by NCEE. This system provides for a high degree of uniformity and reciprocity. States set the education and experience levels (typically four years after graduation) required by those desiring to write the principles and practices examination. Examinations The principles and practices examination calls for answering eight of 20 equal weight questions; one on engineering economics, 19 on engineering. Economics may enter into engineering questions, but only provided the question is not answerable by an economist without engineering training. In preparing examinations, NCEE strives to use questions that require some judgment and can be more effectively answered by someone with four years experience beyond college. The aim is to assess entry-level professional

Jan 2, 1984

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve&apos;s Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company&apos;s large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve&apos;s initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve&apos;s operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980