Search Documents

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By Robert W. Buechley, Charles R. Key, Jonathan M. Samet, Marion V. Morgan, Arnolfo A. Valdivia

INTRODUCTION The Uranium Epidemiology Study at the University of New Mexico was initiated in 1977 with the objective of assessing health effects of uranium mining in the Grants, New Mexico, area. The planned approach was a cohort study of mortality that would capitalize on the availability of health records at the Grants Clinic. During the first year, emphasis was placed on determining the feasibility of the proposed study: Were adequate records available? What was the quality of available information? Could a cohort be established? The first year's work confirmed the study's feasibility (Buechley, 1979). Subsequent efforts have focused on the health and exposure data base and comprehensive follow-up. A retrospective cohort study of early miners is in progress; a prospective cohort study of miners who began working under the current Federal standard is planned. This report will summarize the current status of the Uranium Epidemiology Study. A chronology of the study's activities follows (Table 1). TABLE 1. Uranium Epidemiology Study Timetable 12/77 Official start of study. 12/77-8/78 Abstracted Grants Clinic records of 21,780 persons examined for mining companies from 7/57 through 12/76. Checked company personnel records to establish who had worked underground 1 year or more through 12/76. 7/78- Obtained physical exam and mining history information on qualified miners from Grants Clinic and companies. 9/78- Obtained working level month information from companies and other sources. 12/78- Checked qualified miners list with New Mexico death tapes and New Mexico Tumor Registry files. 9/80- Submitted qualified miners list to Social Security Administration for search of its records. 12/80- Obtained copies or abstracts of early State Health Department and Mine Inspector's reports. 3/81-4/81 Conducted Pilot Respiratory Disease Survey. 3/81- Verified underground status of qualified miners via company personnel records. 3/81- Verified smoking and mining histories of qualified miners via Grants Clinic records. 3/81- Began establishing cohort with first underground experience after 1970. 4/81- Checked qualified miners list with Post Office, Voter Registration Office, Motor Vehicle Division, telephone directories, city directories, and other sources. BACKGROUND Uranium Mining in New Mexico The Grants, New Mexico, uranium belt measures some 110 by 25 miles in Cibola, McKinley, and Sandoval counties (Kelley, 1963). The three chief mining districts are, from east to west, Laguna, Grants, and Gallup. Average annual production was about 5,500 tons, or 45% of United States uranium, from 1966 through 1978. Despite a drop in this figure in 1979, to 40%, New Mexico still leads the nation in uranium reserves and production (Hatchell, 1981). In 1918 carnotite, a yellow uranium vanadate, was identified in the Shiprock area (Chenoweth and Learned, 1980; N.M. Energy and Minerals Department, 1981). It received little attention at the time because of its apparently limited volume. In 1950 an important uranium outcropping was discovered by chance in limestone at Haystack Butte, northwest of Grants. In 1951 deposits were discovered in sandstone at Poison Canyon, north of Grants, and at Jackpile, northeast of Laguna. In 1955 finding of radioactive cuttings at an abandoned oil test site near Ambrosia Lake led to drilling and discovery of the first underground deposits (Melancon, 1963). Ore bodies were also found near Church Rock in the 1950's (Rautman, 1977). A uranium rush followed. At various times during 1952-1962, 60 mines and 5 mills were in operation (Gay, 1963). In the early 1960's the price of uranium fell, and many miners left the area. Subsequent market fluctuations have produced shutdowns and consolidations, development and expansion. Many early uranium miners came to New Mexico with

Jan 1, 1981

By V. N. Kazakidis

With increased levels of automation, capitalization, and empowerment of citizens, the traditional axis of labour versus capital or national government versus capital, upon which the allocation of benefits from a mining project was traditionally based, has shifted primarily to a capital versus community axis. In light of this paradigm shift, it is critical for the sustainability of mining that economic indicators be considered at the pre-feasibility, feasibility, and permitting stages of a project. Such indicators should emphasize the ?ripple effect? of the economic impact of a capital-intensive mining investment on a region due to outsourcing, as well as the diversified spin-off opportunities and the technological advances that can be exploited by local communities.

Jan 1, 2003

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By O. K. Kuznetzov, L. A. Otrozhdenova, N. D. Malinovskaya, I. I. Maksimov, N. D. Khodov

While processing zinc cakes with application of Weltz-technology silver remains unrecovered and goes into clinker. In order to prevent it the elaboration of effective silver recovery methods from zinc cakes before their weltzing becomes necessary. A combined method of zinc cakes treatment with leaching and flotation in a closed water circuit has been worked out. The technological scheme envisages the use of sulphgydril collectors in combination and comprises a series of consecutive operations: leaching, filtration, precipitation(cementing) and flotation. Total silver recovery is approximately 94%. The technology elaborated has been realized in a project by which the construction of a new shop is under way now.

Jan 1, 1995

By Philip Antunes, A. E. (Tony) Reschke

"INTRODUCTION Tunnel Boring Machine (TBM) operations require the injection of material into the annular tail voids as the machine advances ahead of the segmental concrete lining. This annular gap is created because the cutting diameter of the TBM has to be larger than the outer diameter of the concrete segments of the tunnel lining. Fundamentally, the two basic types of annular grout are thick, concrete like mortars and thin, mobile, two-component grouts. While some European countries seem to still favor the concrete like mortars, from a global perspective it is now the two-component type grouts that dominate the industry. Two-component type grouts are comprised of an “A” component grout (typically cement, flyash, bentonite and a retarder/stabilizer) and a “B” component accelerator (sodium silicate or water glass as it is sometimes known). They are thus sometimes referred to as A/B type or bi-component grouts and were pioneered by the Japanese over 30 years ago. They offer a host of operational benefits over thick mortars, such as reduced settlement (Feddema et. al., 2001), effective penetration of the void space, with less energy, and reduced strain on the segmented linings (Robinson et. al., 2007). Two-component grouts are highly mobile and can be pumped many kilometers. The use of a retarder/stabilizer can also extend the shelf life of the “A” component grout for several days while the early strength of the accelerated grout stabilizes the ground and supports the segmental liner almost immediately. The batch plants that prepare the two-component grouts use one of two possible mixing methods for preparing the “A” component grout. The simplest plants use paddle type mixers and numerous tunnels worldwide have been successfully grouted using this technology. However, a superior type of mixer is available, namely the high shear colloidal mixer. Keller Colcrete successfully pioneered the development of the colloidal mixer back in 1937 and for over 75 years colloidal mixers have been internationally recognised as the most efficient method of mixing cement based grouts (Houlsby, 1990). These mixers are used in grout preparation for radioactive waste encapsulation, hydro dam grout curtains, soilcrete jet grouting, soil nailing, and numerous other geotechnical applications. In tunnelling, these mixers are also used for ground treatment, compensation grouting and for the preparation of bentonite lubrication for pipejacking. It has been only within the last decade however that these high-shear colloidal mixers have been adapted for use in the preparation of two-component grouts."

Jan 1, 2016

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By Michael M. Carroll, Zhu-ping Duan, Han-ping Chin

INTRODUCTION The inelastic stress-strain behavior of rocks has urged engineers to seek for the possible application of plasticity to engineering pro¬jects such as tunnels, oil wells, dams, etc. for a long time. Early efforts in this direction have tentatively used the classical theories to solve some axisymmetric problems, in which the rocks were treated as perfectly plastic and nonfrictional materials (Talobre, J. A., 1957). Meanwhile, one of the fundamental assumptions is that the volume strain of elastoplastic material is purely elastic. Drucker and Prager (1952) developed a perfectly plastic and frictional model with a generalized form of Mohr-Coulomb law, which serves as both failure criterion and yield criterion. Although the associated flow rule gives unacceptably large dilatancy, this model is a very important step to deal with the frictional behavior of geological materials. As a further step, Roscoe et al (1963) and Schofield and Wroth (1968) proposed a Cam-clay model, which accounts for the yielding before the material reaches a failure envelope and reflects the plastic volume strain as a strain hardening factor, and the open end of the Drucker-Prager envelope is capped by a family of yield surfaces, the envelope is made conforming with crit¬ical void ratio line. The proposed shapes of the cap have been based on experimental data and on convenience of mathematical descrip¬tions. Drucker, Gibson and Henkel (1957) introduced a spherical cap for soils, while in Cam-clay model the cap is semi-logarithmic yield function derived from the result of triaxial tests. DiMaggio and Sandler (1971) proposed an elliptical model for sand, in which the hardening function depends exponentially on plastic strain. Sandler et al (1976) used a plane cap model to express the behavior of a wide range of geological materials of which the nonlinear hysteretic nature is significant. Mizuno and Chen (1982) illustrated the physical mean¬ing of cap models and their adaption to finite element calculation. In recent years, Carroll et al (1972, 1980) have studied the com¬paction of porous materials under hydrostatic pressure and discussed the mechanism of the nonlinear response thoroughly. Analytical and numerical analysis of the hollow sphere model by Curran and Carroll (1979) predicted an initial yielding surface, dependent on the initial porosity, and showed a strong coupling between hydrostatic and deviatoric effects. All these main features from the abovementioned theoretical research are visualized by the experimental data on Boise sandstone (1984). The combination of such previous work would be logically the construction of a plasticity model for porous rocks which, following the tradition of assigning the name of birthplace to a special model, is called Cal-Rock model (Carrol, M. M., 1984). The results of triaxial tests along different loading paths reveal the compaction characteristics for deviatoric and hydrostatic stress separately. the fitting of the nonlinear stress-strain curves leads to a construction of yield surfaces. Moreover, an uniaxial strain test gives the strength envelope which is the critical state line. The whole model is composed in the frame of elasticity theory. The concept and representation of plasticity used here are in the spirit of Naghdi¬Casey theory (Casey and Naghdi, 1984 and 1984, Naghdi and Trapp, 1975). In order to find the way of using such a plasticity model in engineering problems, the stress field in a thick-walled cylinder of porous material is calculated. This is an axisymmetrical problem with plane strain, which is an idealization of oil well in an infinite medium. Because the constitutive relation is highly nonlinear, a numerical method has been utilized to obtain the solution. CONSTRUCTION OF CAL-ROCK MODEL (1). Elastic-plastic constitutive equations The basic assumption is that the yield surface in stress space depends on one parameter, namely the plastic volume strain, as the data on Boise sandstone suggested. Starting from this point, the theory formulated in stress space and in strain space by Naghdi and his co-workers (1975, 1981) can be simplified. The simplified yield function is

Jan 1, 1986

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By Cong Shi, Cuiping Li, Enji Sun

"Tailings dam is a subsidiary facility of mining production. In order to decrease tailings dam accidents caused by the failure of flood drainage system, this paper proposed a framework of potential failure detection system of tailings dam flood drainage facility based on three dimensional panorama technology. A collection device of three dimensional panorama is designed to capture the onsite images of flood drainage system of tailings dam. The spatial information of flood drainage facility of tailings dam is recovered through projecting the image information to spherical surface by using three dimensional panorama technology. Two dimensional images are transformed into three dimensional images in three stages of panorama images process, which are pretreatment, registration and splicing. Combined with the framework of HTML5, panorama images are embedded into webpage. These web pages have the functions of user interface that the images could be displayed, moved and zoomed. With the function of interaction with panoramic display, 3D panorama scenes can be changed and scaled. Browsing the webpage is helpful to find potential risks such as possible holes, fractures and leakages of flood drainage system of tailings dam. The realization of this system can detect the potential safety risks of flood drainage system of tailings dam. The application of this system would improve the safety and provide the ability of accident pre-warning. It is useful to maintain the healthy and sustainable operation of tailings dam.Introduction It is reported by Xie et al (2009) that tailings dam are necessary facilities for mine production and places which constructed by damming troughs or encirclement used to store tailings that eliminated after ore selection in Metal and non-metallic mines. It is reported by Mei (2012) that tailings dam is a dangerous source of high-energy man-made debris flow, the collapse of the tailings dam takes devastating damage, which seriously threatens the safety of life and property of the enterprises and the downstream residents. It is reported by Dong (2011) that the collapse of the tailings dam causes secondary disasters such as environmental pollution at the same time. It’s a serious impact on regional economic development and social stability. The phenomenon of collapse of destruction is general excessively of tailings dams in China. It is reported by Zhang et al (2011) that most of these phenomena are caused by flood over the top of dams. The main reason is the lack of capacity or the failure of the drainage system. There are also accidents caused by the failure of drainage system in foreign countries in recent years. For example, November 5th 2015, the tailing dams collapsed because of the insufficient drainage capacity of the Germano mining area in Germano Mariana area in central Minas Gerais state in Brazil. After a small post-earthquake, the liquefied tailings fill sand submerge downstream cities and towns. It finally destroyed 158 houses, killed at least 17 people, polluted 663km river and destroyed 15 square kilometres of land along the river. It is reported by Rico et al (2008) that it’s necessary to continuous monitor and control the tailings drainage system in order to reduce the occurrence of tailings accidents and guarantee the sustainable production of the mine. The traditional artificial detection methods of flood drainage system of tailings dam exist many problems such as heavy workload, low efficiency, and susceptible to meteorological conditions. And it is reported by Luo (2013) that the tailings dam wastewater is corrosive which result a certain disease in flood discharge facilities such as tailings drainage culvert, etc. In order to realize the effective monitoring, management and maintenance of flood drainage system of tailings dam, advanced technologies need to be used to acquire the information of collection and management of flood drainage facilities of tailings dam."

Jan 1, 2017

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By M. H. H. Mahmoud, T. A. El-Barbary, E. A. Abdel Aal, I. A. Ibrahim, A. K. Ismail

Fertilizer-grade phosphoric acid with a P2O5 concentration of 50% should contain less than 1.5% Fe2O3, otherwise, the P2O5 water solubility of the fertilizers prepared from high-iron acids will be low. High-iron Egyptian phosphate concentrates fromAbu-Tartur and Sebaiya- West were leached with sulfuric acid and recycled phosphoric acid to produce 50%-P2O5 phosphoric acids containing 4.0% and 2.7% Fe2O3, respectively. The high iron contents were reduced to the industrially accepted limit of 1.5% Fe2O3 by precipitation with potassium sulfate. The factors affecting the effi¬ciency of the precipitation process, e.g., temperature, time and K2O/Fe2O3 ratio, were systematically studied, and the optimum conditions were achieved. The clarification of the prepared phosphoric acid from iron-containing sludges was also investigated by varying the time and temperature. The utilization of the separated sludges as fertilizer and recovery of P205 by pulping in water were also evaluated.

Jan 1, 2000

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981