Search Documents

"The use of gas, temperature and airflow sensors to monitor mine ventilation atmospheres offers numerous safety and operational bene-fits to mines. Detection of dangerous gases, changes to airflows and temperature variations are some of the obvious benefits of using at-mospheric sensors in mines. The prediction of atmospheric conditions between sensors however is potentially difficult, and gaining full cover-age a mine will require either many sensors or a method of extrapolat-ing and predicting atmospheric conditions between and downstream from a sparser array of sensors. A dynamic simulation computer model technique is demonstrated to predict time based changes to atmosphere conditions downstream from sensors. The dynamic model predicts the time based changes to conditions throughout a mine model by simulating the mixing, addition and dilution of gases and airflow changes in incremental time steps. The advantages of this method is that a real time overview of full mine atmospheric conditions can be viewed at all locations, even areas without sensors. In addition, with careful planning and consideration of potential contaminant sources, the number of required sensors can be minimized. INTRODUCTIONMine Ventilation Sensors The importance of continuously monitoring mine atmospheres has been recognised since mining underground began and the effects of harmful gases on human health were discovered. Through the 19th and early 20th centuries, coal miners would take canaries underground with them as an early detection system against life threatening gases such as carbon dioxide, carbon monoxide and methane (Figure 1). The canary, normally a very songful bird, would become agitated, stop singing and eventually die if not removed from these gases, signalling the miners to quickly exit the mine (Davalle, 2011)."

Jan 1, 2016

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project. 

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.

By Fiona M. Doyle, Christopher R. Lubeck, Michael C. Chin

The fundamentals behind a novel approach for creating inorganic/polymer hybrids are described. The binding of +2 charged ions, specifically Cue-and Cat+, to ionic functional groups is explored through UV-Vis spectroscopy and zeta potential measurements. The novel approach uses an electric field to drive ions into a functionalized polymeric matrix, thereby inducing the precipitation of calcium phosphate species. Scanning electron microscopy images of the resulting composite illustrate the results of these precipitations with two distinct morphologies observed.

Jan 1, 2003

By G. Vogt

Water is one of the most important ressources of our planet. Unlike many other natural resources, water cannot be substituted by anything and must therefore be handled with the utmost care. Depending on the region and the possible shortage of water, the importance of water increases even further. Water consumption is not the only factor. In the construction industry, water pollution from auxiliary and operating materials and processes as well as other contaminants and their resulting load on wastewater play an important role. The sources for wastewater on tunneling construction sites are various: Washing water, seepage water accumulating in construction pits, tunnel water, water used in the slurry circuit in fluid-assisted tunneling methods or water from concrete work and stone cutting all these waters are contaminated with a range of pollutants like solids, hydrocarbons, heavy metals, etc. These contaminants can be removed or treated/reduced with the help of specifically designed wastewater treatment plants (WTPs). After the treatment the cleaned water can be either, in best case, reused on the construction site itself or discharged into water utilities like the available sewer or river pin respecting their discharge requirements. Due to dwindling water resources globally, the continuously rising discharge limits and the ever more important aspect of sustainability the use of WTPs on tunneling construction site will be indispensable. In this paper, it will be presented how these systems are designed and work, what advantages they offer environmentally as well as financially and what to look out for when planning and implementing such a system onto jobsite.

Jun 23, 2024

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By L. B. Phelps

The nation is confronted with thousands of acres of abandoned coal lands. In Pennsylvania alone, these lands have been estimated to cost $15 billion to reclaim (Pennsylvania Bulletin, 1985). One way to deal with this problem is to provide a mechanism by which the active mining industry can undertake to remine certain of these abandoned mine areas. Remining is classified as reaffecting previously mined areas in order td extract the remaining coal reserves while improving the environmental quality of these lands through land restogation and abatement of pollutional discharges. However, there currently is a disincentive for operators to plan to extract reserves on these abandoned mine lands which have preexisting pollutional discharges. Therefore, they presently avoid them. This is because of the "potentially unlimited liability of post- mining treatment for any discharges that would remain after mining? (Pennsylvania Bulletin, 1985).

Jan 1, 1987

By Robert G. McLusky

Since 1998, environmental extremists have waged war with the central Appalachian coal industry in West Virginia and Kentucky. In particular, they have filed three lawsuits challenging the legality of excess spoil ‘valley fills’ under CWA, NEPA and SMCRA: 1) Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D.W.Va. 1999), rev’d. 248 F.3d 275 (4th Cir. 2001); 2) Kentuckians for the Commonwealth v. Rivenburgh, 204 F.Supp. 2d 927 and 206 F. Supp. 2d 782 (S.D.W.Va. 2002), rev’d. 317 F.3d 425 (4th Cir. 2003); and 3) OVEC v. Bulen, 2004 U.S. Dist. LEXIS 12690, July 8, 2004; OVEC v. Bulen, 2004 U.S. Dist. LEXIS 16078, August 13, 2004.

Jan 1, 2005

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

By Julio C. Martinez, Jeffrey L. Rice, Hayden Weschler

This paper details the extensive underpinning required to hold up the 39th street Bridge while demolishing its massive support piers and building a 30ft deep Cut/ Cover RR tunnel beneath it. The underpinning/SOE support required the construction of 16 large hand dug pits 36ft deep that were reinforced and concrete filled. In addition, an extensive steel support system was tied into the bridge super structure. All of the underpinning/tunnel construction was done while a 110ton crane sat directly atop the heavily trafficked – 66 ft. wide bridge. The tunnel excavation, concrete lining and final bridge pier support work will also be presented. All work was done within 5ft of active mainline tracks and that required tight grouting behind all lagging to eliminate any track settlement.

Jun 13, 2021

By I. C. Watson, J. W. Klokow, A. F. Knoetze, R. G. B. Pickering

In the late 1970s and early 1980s there were a number of attempts to use Tunnel Boring Machines in deep level gold mines. These attempts must be regarded as unsuccessful. Since then there have been comprehensive developments in tunnel boring equipment and tunnel support technology. This paper defines the problems experienced in those early trials, reviews the technology development, and concludes that tunnel boring in deep level goldmines can be justified in today’s environment.

Jan 1, 1999

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By J. C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1995

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

This study applies a machine-learning technique known as multiclass logistic regression on a 10-year injury dataset from the U.S. Mine Safety and Health Administration (MSHA) to determine miners’ susceptibility to injury and to help identify significant risk factors associated with different classes of injury. The analysis identifies specific risk factors that influence a mineworker’s susceptibility to a given class of injury: nonfatal with no days lost or restricted activity; nonfatal with days lost and/or days of restricted work activity; and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal versus noncoal), experience on the current job (years), shift start time, employment type (operator versus contractor), mining district and type of accident. The results of the analysis indicate that a miner’s experience on the job (the number of years worked in a current job) is a significant risk to injury occurrence, even for those with decades of total mining experience.

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By William Gleason

"The Colorado School of Mines has used the Edgar Mine in Idaho Springs as an experimental mine to teach students since 1921. Since the school acquired the former gold, silver, lead and zinc mine, countless students have received hands-on engineering lessons on their way to earning mining engineering degrees. On Dec. 14, the House Subcommittee on Energy and Mineral Resources held a historic field hearing about the future of mining education in the United States in a classroom about 300 m (1,000 ft) inside the Edgar Mine. Representatives Doug Lamborn (R-CO), Rob Bishop (R-UT), Cresent Hardy (R-NV) and Ed Perlmutter (D-CO) were on hand for the first ever congressional hearing held in a mine where they heard testimony supporting the Mining School Enhancement Act, which was introduced to Congress by Hardy and Perlmutter on Oct. 9, 2015. The act, which is part of a larger mining development and reclamation reform package, seeks to address the absence of a viable pipeline necessary to replenish current faculty vacancies in United States Mining Schools. “What better place to hold a hearing to discuss the need for future mining engineering experts,” Subcommittee Chair Lamborn said in his opening statement. “It is a need felt by industry, states, the federal government as well as nonprofits.” The Mining School Enhancement Act would redirect millions of dollars in fees that are being collected from active mining operations to fund the research and educational programs at engineering schools with mining programs. Those fees now are being used in the form of grants awarded by the Surface Mining Control and Reclamation Act of 1977 (SMRCA)."

Jan 1, 2015

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992