Search Documents

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By Thomas F. Stinson

Energy-producing states see severance taxes as attractive sources of increased revenues for otherwise tight budgets. Consumers in energy-poor states, however, protest that current rates are excessive and have moved to obtain a reduction. The US Supreme Court heard two cases questioning such taxes during its 1981 term, and Congress, in each of its last two sessions, has seriously considered measures placing a ceiling on severance tax rates. Although discussions usually focus on coal severance taxes levied by Montana and Wyoming, ramifications of changes in national policy are much larger, potentially affecting mineral taxes in all states. Severance taxes yield substantial revenues in some states, as illustrated in the accompanying table. In fiscal 1980, Texas collected more than $1.5 billion from such taxes, while Louisiana, Alaska, and Oklahoma collected $525 million, $507 million, and $436 million, respectively. Oil and natural gas production were the major items taxed. While the table shows only the 10 states with the largest severance tax collections, a total of 17 states had severance tax receipts exceeding $10 million in 1980. The enormous increases in severance tax revenue between 1970 and 1980 can be seen from the table by comparing columns A and B. For the 10 states shown, revenues increased from $650 million to $3.8 billion during that period, due to a combination of higher prices, increased production, and new or increased taxes. In most states, increases in prices and production were more evident than higher tax rates. Although the revenue increase is impressive, it understates the extent of changes occurring during the past decade. Since tax collections are shown for fiscal 1980, the full impact of the decontrol of domestic oil prices is not evident. Also, taxes on natural gas reflect controlled prices. When full de-control of natural gas occurs, significantly higher revenues can be expected in gas-producing states, even if tax rates, production, and world prices remain constant. These increases in severance tax revenues, coupled with further increases expected to accompany natural gas decontrol, have produced fears that a substantial transfer of income is taking place from residents of energy-poor states to those living in energy-rich areas. Others worry that increased severance tax revenues will be used to substitute for a substantial portion of state taxes that would have otherwise been collected from firms and individuals. The resulting improvements in tax climate, it is thought, may encourage firms and workers to migrate to energy-producing states. While these issues are often portrayed as pitting energy have-nots against the haves, such is not entirely the case. Much of the original impetus for limits on coal taxes came from Texas residents, the state collecting the most severance tax revenue. One way of gaining perspective on these concerns is by examining severance taxes per capita and as a percent of state tax collections (see columns C and D in the table). When this is done, Alaska, where 1980 taxes on oil and gas production totaled more than $1300 per capita (and 35% of all state tax collections), stands out as a special case. There, the state was able to eliminate some individual taxes, place revenues in a permanent trust fund, and consider offering a rebate of some previous income

Jan 4, 1982

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By G. E. Sreedhar, R. Kumar

The pockets of high silica blue dust across the entire high grade hematite deposits in the Bailadila sector bothers the excavation activity due their iron content, which is higher than the threshold value specified by the Indian Bureau of Mines and the agony of stacking them separately due to their fragile & powdery nature. The physical nature of blue dust and its negligible alumina content makes these a potential source of hematite, which is a blessing in disguise. As most of the particles are in the form of an independent grain making it appropriately suitable feed for dry magnetic separation and thus the dry beneficiation has turned a bane into boon by enabling to produce concentrate either suitable for using as DSO or amenable for blending. The emphasis on carrying out dry beneficiation studies in the present context serves the purpose of mineral conservation, mitigates the issues of excavation and stacking as well as conservation of water resource. This paper describes the laboratory and pilot scale dry beneficiation studies carried out on blue dust of 48 – 60%Fe and Silica up to 30% at 25 Kg/hour to 400 Kg/hour, resulting in production of concentrate assaying 60 – 65%Fe. INTRODUCTION High silica blue dust (HSBD) is associated with Banded Hematite Quartzite (BHQ) and is available in abundance in various pockets across the Iron ore body in the Bailadila region of Chhattisgarh state. High Silica Blue dust occurs in the form of free granular particles and also as friable lumps. The chemical quality of this falls under sub-grade category (45 – 55%Fe) and as per the guidelines of Indian Bureau of Mines, these are to be stacked and conserved as future resources of Iron if it can’t be utilized in the present circumstances. Due to its friable nature, stacking of HSBD is a challenge and it is also compounding the problem by polluting the air under high velocity wind conditions. Because of its physical nature and occurrence in pockets pose challenge to systematic mining. The existing processing set up of the operating mines is designed to treat either Direct Shipping ore (DSO) or Run-of-Mine (ROM) have grade >60% Fe. The present practice of beneficiating iron ore fines (<1 mm) comprise combination of two or more processes such as desliming, hydraulic classification, magnetic separation and flotation apart from requirement of grinding depending on liberation characteristics. The HSBD which is predominantly occur as free granular particles, is significantly low in its alumina content. This gives us an opportunity to utilize them by exploring a suitable beneficiation process so that the concentrate produced can be used as a sweetener for alumina rich iron ore/concentrate. Thus, in the present study, an attempt has been made to adopt dry high intensity magnetic separation technique to explore the amenability of the high silica blue dust for beneficiation.

Jan 1, 2019

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicates the potential for scrap formation, validated through laboratory experiments with varying coke rate, basicity and holding time. The investigation discovered that smelting this combination could yield a metal product consisting of 59 percent Fe, 24.93 percent Cr, 7.56 percent Mn, 0.62 percent Ni and 0.93 percent Si. The optimum basicity was found to be 0.6 with 80 percent recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall carbon dioxide emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of US$330/t.

May 1, 2024

By M. Brändström, R. Dube, J. Moyo, T. Perkins, G. Bermudez, L. Bartsch, C. Smith, R. Sorensen

The Kennecott Copperton concentrator is currently the bottleneck for the Kennecott operation and several projects have been initiated to increase throughput. This increase in grinding circuit throughput has resulted in a coarser grind size which has impacted flotation circuit recovery. Metso Outotec 300m3 forced air tank flotation cells are currently utilized in the rougher flotation circuit at the Copperton concentrator. Higher overall recoveries have been observed on the newer Outotec tank cells compared to the original 85m3 self-aspirated flotation cells they replaced. However, coarse particle flotation response on these large, forced air cells did not show encouraging results when compared to smaller previously installed cells. This coarse recovery loss has been attributed to the longer froth transport duration and transport distance on large cells (100m3 and larger). Cell manufacturers addressed the risks of additional coarse particle losses in large cells by installing concentric circumferential launders and crowders (also called center launders). These are designed to reduce froth transport time and distance in the last cells in rougher stages where low residual floatable minerals causes a lack of froth mobility. The center launders also increase froth crowding, which also helps to increase froth transport velocity and increases copper and molybdenum recoveries. A trial set of the center launder retrofits were installed on the last three tank cells in one of the parallel rougher flotation rows at Copperton. The launder retrofits were installed at the end of October 2020 and monitored until March 2021. This six-month trial showed statistically significant improvements in copper and molybdenum flotation recoveries through the rougher circuit.

Mar 2, 2022

By W. E. Heinrichs, R. W. Davis

Introduction Cross borehole seismic tomography (CBST) is a geophysical technique that allows definition of the distribution of some physical rock property between two boreholes. The method is similar to the computer-assisted tomography (CAT) scans used by the medical industry. This paper describes the method, its applications and the developing trends in its use that interest the mining industry. The idea of using tomography in connection with geophysical methods for measuring rock properties between boreholes has been around for three or four decades. Until the advent of high-speed, large-capacity computers, the necessary calculations were too formidable for production use. Another factor in the development of the technique has been the refinement of a mathematical base to meet the needs of the medical industry. The geophysical applications have benefited from this refinement. An extensive discussion of the basic theory is given in Kak and Slaney (1988). CBST, although widely researched and written about, is still not extensively put to use in mining and engineering projects. Most real world examples in the literature have come from research carried out by government laboratories or by large companies. An exception is the regular use by Prospection Geophysique Francaise (Cottin et al., 1986) in damsite investigations. The Japanese appear to be doing extensive research and testing of CBST&apos;s uses in civil engineering projects (Saito et al., 1988). Canada is researching the use of the method in connection with nuclear waste site investigations (Wong et al., 1987). Finland has tested the method in connection with a foundation investigation for a nuclear power plant (Cosma et al., 1984). In the US, the US Bureau of Mines has taken an interest in using CBST as a means to enhance in situ mining operations (Tweeton, 1988). Major oil companies are examining the method as a tool in oil field development (Justice et al., 1989). Description of the method CBST involves placing a series of receivers down one borehole and recording transmissions from an energy source placed successively at a series of positions in another hole. The objective is to generate a dense network of seismic raypaths between the holes. The denser the network of raypaths, the better the features between the boreholes are resolved. Either seismic travel times or sine wave amplitudes are measured by the receivers. Analysis of travel times between boreholes develops a picture of rock velocities between the holes. Analysis of seismic wave amplitudes develops a picture of the distribution of energy transmission characteristics between the holes. These seismic properties can be used to define occurrences of fracture zones, lenticular sequences or other important geologic data not apparent from examination of the borehole logs. When longitudinal (compressional) and transverse (shear) waves are analyzed, the physical properties, such as elastic moduli, can also be mapped. When wave amplitudes are measured, rather extensive corrections to the data are necessary. There is some disagreement among researchers as to the feasibility of making some of the corrections. For this reason, this paper will concentrate primarily on travel time analysis. Wave amplitude analysis will be mentioned occasionally only in passing. This does not mean that amplitude analysis does not provide important data on rock parameters, only that for the present there are limitations on its uses. Vertical seismic profiling (VSP), extensively used in recent years in oil exploration, is similar to CBST. Instead of using two boreholes, however, the VSP method uses an array of seismic sources or detectors down one hole and an array of detectors or sources along the surface radiating outward from the hole. While adequate for determining vertical velocity distributions, the VSP method is not, by itself, suitable for most engineering or mining projects. Computer programs used to analyze the field data make use of the fact that the total travel time or change in signal amplitude between boreholes is described by Dines and Lytle (1979) as: [9k = f Rk f( x,Y) ds (1)] where gk = the total time or attenuation along the kth ray path,

Jan 1, 1992

By K. E. Brown, T. D. Murphy

At Monterey Coal&apos;s No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.

Jan 1, 1993

By R. C. Schmidt

The Mont Klahoyo magnetite deposit is located about 600 km northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 million tons grading 36% iron. The deposit, occurring at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations, is associated with amphibolites, pyroxenites and gneisses of the Liberian Shield. At Mont Klahoyo occur two separate iron formations of which the lower member is the ore body. This lower member consists of a highly metamorphosed - banded quartz-magnetite iron formation in which iron silicate bands alternate with beds of quartz-magnetite. mphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated overturned "Z" shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m and outcrops intermittently over a distance of approximately 5.5 km. Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K-1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) with the remaining quartz-magnetite units (oxide facies) repre¬senting the important ore zones of the Mont Klahoyo deposit. The ore-bearing "K" units are subdivided further, based upon their specific lithologies, iron content and concentration characteristics, into eleven ore types. The identification of these ore types is considered particularly important to mine planning and flowsheet design. A cap of oxidized materials overlies the primary quartz-magnetite iron formation but no enrichment has occurred. It is proposed that the Mont Kalhoyo iron formations were deposited, possibly chemically, in a volcanic environment as a siliceous iron formation with volcanism providing the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a relatively coarse-grained quartz-magnetite-silicate iron formation.

Jan 1, 1979

By S. Pollak, J. Rickard

The Long Baseline Neutrino Facility Far Site in Lead, South Dakota is currently under construction and involves drill and blast excavation of the largest and deepest caverns in North America. This paper will review how the geotechnical risks are being managed through careful consideration of excavation sequence, completion of exploratory pilot tunnels, implementation of a robust instrumentation and monitoring program, and validation against the design. Aside from having a cross section of 5,900 square feet and being situated at a depth of one mile, the caverns also employ a unique permanent rock bolt solution which underwent a significant pre-production pull testing program involving varying installation methods and being subject to blast vibrations. The behavior of the schistose rock mass and performance of the ground support are being continually monitored throughout the construction phase.

Jun 13, 2023

By Vaughn Astley, Hassan El-Shall, Ponisseril Somasundaran, Regis Stana, Patrick Zhang

In the past, when phosphate rock quality was good, few paid attention to any of the impurities or other qualities associated with phosphate rock. In general, they had little or no effect on the ability to make the phosphate products for the market. However, as phosphate rock quality declined, it was apparent to the rock consumers that the individual impurities had a significant impact on their processes. FIPR is presently funding an analysis of operating plant data to determine the range of the effects of rock impurities on production plant performance. The study will not be completed until 2002. IMC has agreed to share some of the information they had developed in the early 1990s.

Jan 1, 2002

By Mark Van Dyke, Mark Mazzella, Gamal Rashed, Nicole Evanek, Brent Slaker

In the past decade, there have been several incidents of massive ground collapses in underground stone mines in the eastern United States. Fortunately, these events have not resulted in any fatalities. However, three mine workers were injured and many others were at risk due to the hazard from the fall of ground and/or the airblast associated with these massive collapses. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to better understand the causes of these massive ground collapses to help prevent their future occurrence. The main objective of this study is to investigate the main factor(s)that initiated one of these massive ground collapses. The authors relied on several tools including three-dimensional (3-D) LiDAR scans for the surface subsidence feature and the underground mine workings around the collapsed area, borescope data at multiple locations around the collapse, S-Pillar analysis for average and unfavorable conditions, and numerical models. The emphasis has been placed on the impact of the following limestone pillar stability parameters: pillar width-to-height (W/H) ratio, benching, the existence of karst features, weak roof, and geological discontinuities. 3-D LiDAR scans were utilized to show the shape and the extent of karst cavities observed within stable pillars around the perimeter of the collapsed area. Together, this coupling of field measurements and observations and modeled systems suggests the potential causes of the collapse.

Jul 1, 2023

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. In this paper we will review technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. INTRODUCTION Portable mine refuge chambers are used in US coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity within the shelter, as well as the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter, 23 humans, and also includes the surrounding mine environment. The thermal simulations were performed using ThermoAnalytics' validated commercial heat transfer prediction code, TAITherm (v12.0). Additionally, TAITherm's Human Thermal Module (HTM) provided the capability to simultaneously model the thermo-physiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and also provided a core temperature response prediction, which can be used to evaluate survivability in heat stress situations [1]."

Jan 1, 2016

By Emily Sarver

"Across all sectors and commodities, a common theme is driving progress in raw resource supply: sustainable development (SD). Over the past few decades, the mining and minerals industries for their part have undertaken significant and intentional changes at every level to become more responsible — no longer to just their shareholders, but also to the environment, to the communities in which they operate and to society at-large. Led by some of the global majors, these industries have indeed helped to define and operationalize the basic principles of sustainable development. Now in the midst of a full-on cultural shift, they are also key players in the continual effort to re-examine and calibrate practices to meet dynamic and increasingly complex objectives.SME’s technical position statementAs a home for so many technical experts and practitioners, SME has long recognized the importance of a commitment to sustainable development by the mining and minerals industries. In April 2016, the Society formally adopted a technical position on the topic following years of participation in, and support for, related activities. The full position statement appears below. It was drafted, revised and presented for approval to the board of directors by SME’s Sustainable Development Committee.Statement of Technical Position on The Mining Industry and Sustainable Development:• The National Environmental Policy Act of 1969 (NEPA) and the Surface Mining Control and Reclamation Act of 1977 (SMCRA) imposed considerable environmental restrictions on the mining industry; SME has always reinforced strict adherence to the laws.• In 2002, SME established a Sustainable Development Committee to lead its efforts in this area and to propel the organization into global prominence.• SME is a signatory to the Milos Statement of 2003 on Sustainable Development, so it is committed to providing scientific, technical, educational, and research skills in minerals, metals and fuels.• SME recognizes that SD programs adopted by the industry have a tangible return on investment through brand recognition and loyalty, facilitation of permitting, reduced occurrence of community protests and vandalism and diminished political risks.• SME actively promotes educational programs that encourage professional growth and interaction with the engineering professional community through books, articles, symposia, short courses and/or conferences on sustainable development in the mining and minerals industries.• SME has developed abundant expertise to provide balanced advice to government bodies, congressional staff and other interested organizations."

Jan 12, 2017