Search Documents

By Kerry Spickelmier

A traveler driving across desolate central Nevada to the Round Mountain property can easily identify with turn- of-the-century prospectors seeking a fortune, or at least an existence, from the high desert. But now a shadow passing overhead is as likely a sophisticated fighter aircraft from Stillwater Naval Air Station as a circling bird, and the famous trails west show only as historical markers along the highway. Even the approximately 400- km (250-mile) trip southeast from Reno or northwest from Las Vegas takes hours now, not days. And the camps of Round Mountain’s early prospectors have been replaced by one of the world’s largest gold heap-leaching operations. While Round Mountain’s uniqueness begins with its scale, it doesn’t end there. Consider the mine’s low cutoff grade of 0.2 g/t (0.006 oz/st) gold, made possible by a new dedicated (not reusable) leach pad. Also, the operation’s degree of automation means that ore dropped in the south crusher system is not manually handled until it is stripped from the pads. There is the bonus of a geothermal field that is tapped to heat the leach solutions in the winter. And, of course, there was that “unexpected” hitch expected in all mining operations. For Round Mountain, it meant buying a gravity plant to process the gold nuggets discovered last summer in a fault gouge.

Jan 1, 1993

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By H. E. M. N. Moursy, Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, D. Chandler, G. Walker, Regis Stana, Patrick Zhang

The reaction kinetics of the acidulation of Moroccan phosphate rock (32% P?05) using 45% nitric acid were investigated using the Shrinking Core Model (SCM) , a newly developed Diffusion Model (DM) and a newly developed Combined Reaction and Diffusion Model (CRDM). This was achieved buy conducting a number of experiments in a controlled batch reactor system at different temperatures. The conversion and the reaction rate were calculated at different time intervals. The SCM based on reaction time and the CRDM characterize the acidulation process of phosphate rock. Diffusion of nitric acid and the products of acidulation at the early stages of reaction through the phosphate rock were found to be the rate-controlling step, resulting in a dif- fusion coefficient, which controls the mass transfer process. The reaction kinetics were found to fit first-order kinetics especially during early stages of reaction time. The deviation of the kinetics from first-order at later stages was due to the fact that the overall reaction was mass transfer controlled with respect to nitric acid and products diffusion.

Jan 1, 2002

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By JURGEN KRETSCHMANN

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy. In this spirit, Germany has decided to erase coal use as an energy source by 2038 completely. This strategy premises a feasible, responsible and sustainable post-mining management. The Research Institute for Post-Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet post-mining challenges. In all efforts, the FZN aims to achieve the fundamental goals of the United Nations to deal with the resources of our planet responsibly and sustainably.

By S. Gopalakrisbn, J. D. Miller, M. Misra

Pilot-scale tests indicate that effective concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% -400 mesh and 0.01 opt*) from gravity concentration were processed with a 5-cm air-sparged hydrocyclone (capacity ~1.0 t/h dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1987

By M. K. Quinn, R. D. Chaffins, A. W. Khair

This paper presents an analysis of the effects of topography on static and dynamic ground movements and severity of damage inflicted on surface structures. A typical site containing varying topographical features (i.e., mountains, hillsides, valleys, and flat bottom land) representing the northern Appalachin region was chosen for the study. Typical subsidence monitoring techniques were employed. Frequent measurements were made as the face advanced.

Jan 1, 1987

By G. Norman Owen, Roger E. Scholl, Tor L. Brekke

INTRODUCTION Underground structures are generally regarded to be safer than surface structures during strong seismic motion, except when crossing a causative fault. Recent studies of observed earthquake damage to tunnels generally support this view, although instances of severe damage and, occasionally, collapse are reported. For proposed underground construction of sensitive structures such as nuclear power plants, liquefied natural gas facilities, and nuclear waste repositories, a verification of the seismic response of underground structures will be required.. This paper discusses the stabilization recommendations used in a study of additional costs required to protect tunnels against ground motion caused by earthquakes and underground nuclear explosions (1). The study is a part of the site investigations for possible construction of a nuclear waste repository. The additional costs estimated in the study are not presented here; only the stabilization measures are presented in the present paper. The tunnels, which would constitute the underground facilities of a possible repository, are assumed to be 5.5 m (18 ft) in diameter and to be located at a depth of 600 m (2,000 ft). Three candidate geological materials are considered: argillite (shale), granite, and tuff. Several peak ground accelerations are used: 0.3g, 0.5g, and 0.7g for earthquakes, and 0.5g, 0.7g, and 1.0g for underground nuclear explosions. Potential damage due only to shaking is considered here. This paper does not discuss problems that result from creep or sudden rupture of intersected faults or from ground failures at portals.

Jan 1, 1979

By Cong Zhang, Huaying Wang, Yixin Wei

"Water inrush is a serious geological accident in underground coal mines. This paper focuses on the method of the bow tie analysis based on fuzzy reliability to assess the risk of water inrush in coal mines. First, post failure probability and repair probability of initiating events are divided into 5 levels. Then triangular fuzzy numbers are adopted to quantify experts’ language and to acquire the reliability rate which close to the actual values by defuzzification and calculation. According to dynamic bow-tie analysis model, using the method of moments to fit the reliability time of events by Weibull distribution and offering the random sampling rule of failure and repair time for illustrating the feasibility of fuzzy reliability evaluation. To demonstrate the effectiveness of the proposed assessment approach, bow tie analysis model of water inrush in coal mines is taken as an example.Introduction Dynamic bow tie (DBT) analysis is composed of dynamic fault tree and dynamic event tree analysis, and considers the impact of the time factor upon risk assessment of a system. There are many algorithms applied to calculation of the probabilities of node accident and accident consequence of dynamic bow tie analysis: Hidden Markov Model, Bayesian Network (Khakzad et al 2013), Integral Algorithm (Amari et al 2003) and Monte Carlo Simulation (Kim et al 2016). In terms of simulated time and practicability, the Monte Carlo Simulation has an advantage over other methods. DBT requires mass data in quantitative analysis, including the failure rates and the repair rates of the basic events of the Fault Tree (FT) and the subsequent events of the Event Tree (ET) at different time points, i.e., the distribution of failure time and repair time. In practical analysis, it is hard to obtain a large amount of exact historical statistical data, which is a major problem of risk assessment. Due to the difficulty of obtaining the exact data and historical failure data of the basic events and the subsequent events, the FT and ET analysis is stuck with the study of minimal cut sets, minimal diameter sets, structural importance and qualitative analysis (Liu and Zhang 2010, Yan et al 2012, Wang et al 2009, Li and Wang 2011). This paper will use fuzzy numbers and the defuzzification method to transform the experts’ language into the failure rates and repair rates of basic events and subsequent events, solving the problem that it is difficult to obtain a large amount of historical statistical data, and will use the method of moment to conduct Weibull fitting of the reliability time to provide the random sampling criteria of event failure and repair time in Monte Carlo simulation."

Jan 1, 2017

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By D. Mudd, G. Robertson

"Ask an average non-industry person on the street “What is coal? What is coal mining? What is a coal miner?” The most common answers are coal is something Santa puts in your stocking for being naughty, coal mining is destroying the earth causing global warming, and a coal miner is a person that uses a pick and shovel to dig coal out of the earth. As farfetched as these answers seem, unfortunately this is the opinion of many Americans. Realizing the lack of educational opportunity regarding coal and coal mining, a first-of-its-kind grassroots coal education program known as CEDAR (Coal Education Development and Resource) was created. What started from a general conversation at the December 1992 North Carolina Coal Institute (NCCI) Winter Meeting at the Mid Pines Club in Southern Pines, North Carolina led to the creation, and later expansion of, CEDAR. NCCI President, Gene McBurney, challenged John Justice, NCCI Board Member from east Kentucky, to come up with an idea of how to improve the image of the coal industry, pledging $5,000 from the NCCI as seed money to assist in the development of any such program. John then met with the leaders of Coal Operators and Associates, Inc., (COA) in Pikeville, KY where they agreed to match the NCCI commitment, as well as to assist in the program’s development. After further meetings with representatives from industry, business, and the local school system, CEDAR, Inc. (of east KY) was born. The first year of implementation, the program offered coal education programs to public and private schools in one county in east Kentucky. Although it started in the coalfields of eastern Kentucky, it certainly did not end there. After an amazingly successful first year of the program, it didn’t take long for industry leaders in the western Kentucky coal-fields to learn about, and take note of this new, unique, and exciting program that provided opportunities for teachers and students to learn, “the rest of the story” about the coal industry. Through the joint efforts of Costain Coal, and the Western Kentucky Coal Association, CEDAR of West Kentucky, Inc. was formed in 1994, and has operated since that time, except for the two year period from 2004-2006. The program restarted in 2006 under the name of CEDAR West, Inc. and continues to be offered in six western Kentucky counties."

Jan 1, 2015

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock&apos; drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By Theodore H. Budd, Austin M. Cooney

The paper discusses the background and theories of the conditions that led to the settlement of a Lovat TBM mining in an earth pressure balance mode on a recent project in Milwaukee, Wisconsin. The settlement occurred independent of human error and caused the cost of the project to increase 50 percent. The project was mined in the highly congested downtown area in alluvial and estuarine deposits, 7.6 m below the water table with a prescribed contract requirement that precluded dewatering in deference to concern for foundations of adjacent existing buildings.

Jan 1, 1989

A coal mine located in southern West Virginia recently set a world record for daily low-seam coal production using a Cat automated longwall plow system. In a 24-hour period on April 10 and 11, 2014, the Pinnacle Mine longwall produced 32,411 t (35,724 st) from the Virginia Pocahontas No. 3 Seam, in a seam height of just 1.42 m (56 in.) along the 298-m (980-ft) longwall face. The Pinnacle Mine, located near the town of Pineville and owned by Cliffs Natural Resources Inc., an international mining and resource company, operates a Cat Gleithobel GH1600 Longwall Plow System. A previous record was set by this system at Pinnacle in August, 2012 when 29,423 t (32,430 st) were mined in a 24-hour period. The record was set by the same system, mining its second panel after a comprehensive rebuild was performed by Carter Machinery, the Cat Dealer in that area. The rebuild encompassed a complete rebuild of the headgate and tailgate armored face conveyor (AFC) drive, the headgate and tailgate special AFC pans, the stageloader drives and return end, the complete crusher and all gearboxes for the plow, AFC and stageloader. Carter acquired the rights to sales and aftermarket support associated with the former Bucyrus mining products, both surface and underground, in 2013. ?Supporting and rebuilding a longwall plow system was a new experience for the Carter service team,? said Chris Curfman, president of Caterpillar Global Mining Sales and Support Division. ?However, given the record production results attained by the rebuilt system at Pinnacle, it?s obvious that they are up to the challenge of supporting the underground product lines at the same high standards and quality level that they have been delivering for many years on the traditional Cat surface mining products.? Tom Bluth, president of Caterpillar Global Mining Products Division, said, ?Caterpillar congratulates the Pinnacle team for this great achievement. Without their efforts and dedication this record would not have been possible. To safely deliver that kind of output from such a thin seam is remarkable. We have been privileged to work alongside their team to demonstrate the capabilities of Cat longwall mining technology. ?