Search Documents

By K. N. Han, M. C. Fuerstenau, T. B. Onlin

A mathematical model describing the concentration profile of fine particles in the axial direction in liquid fluidized beds has been developed for the removal of fine particles. A forward finite differentiation technique has been used to solve a continuity equation with a source term to predict the concentration profile and, hence the recovery as a function of time. With the aid of experimental results obtained using a fluidized bed of 3-cm diam, dimensionless parameters were identified. These parameters were used to predict the concentration profile of fine particles in fluidized beds of larger sizes. Four different sizes of fluidized beds, namely, 1.3, 3.0, 4.0, and 7.5 cm in diam, were used in this investigation. The amounts of bed particles used included 4, 8, 16, 24, 59, and 120 g, and the size of bed particles were 48x100, 100x150 and 150x200 mesh.

Jan 1, 1987

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998

By Brian W. Hester

All gold occurrences in Tanzania are of Precambrian age and in geological settings similar to gold deposits in other parts the world. The three main areas of interest are perhaps the least prospected of areas of gold mineralization in Precambrian rocks in non- aligned, or market economy nations. Historic production exceeds 77.660 kg (2.5 million oz). Current results by small scale workers go unreported, but have been estimated to be as high as 11.000 kg (350.000 oz) annually. Gold occurs in both lower and upper Precambrian rocks. In the older. gold is associated with greenstones and iron formations typical of many cratonic areas of Precambrian age. The Tanzanian Craton lies in the north west quarter of the country where it is flanked on both east and west sides by mobile belts involving upper Precambrian rocks of high metamorphic grade. Gold occurs in fractures in the western belt within two distinct areas.

Jan 1, 1989

By Olli Järvinen

The precious metal refinery process is divided into the five process stages: 1 .copper/nickel leaching in autoclave 2. selenium roasting furnace 3. doré metal smelting furnace 4. silver electrolysis 5. gold recovery system. The process has been developed during the years in Outokumpu Harjavalta Metals, which treats about 600000 kg /year copper anode slime. The slime treatment process route in Outokumpu Pori plant has been developed from year 1941. During this period the process has been improved radically. The major changes has been the atmosphere leaching into the autoclave leaching, the sulfuric acid roasting furnace was changed into sulfuric dioxide / oxygen roasting. The old doré smelting furnace has changed into the TROF converter and the gold electrolysis / aqua regia process has changed into the quick hydrochloric acid leaching process. The current production in Pori plant is 30000 kg of silver, 1000 kg gold, 30000 kg of selenium and some hundred kg of platinum- palladium concentrate.

Jan 1, 1995

By William D. Leech, Peter S. Buskirk

Virginia Electric and Power Company commencing in early 1985 will begin operating the Bath County Pumped Storage hydroelectric facility, presently the largest capacity installation of its kind. Six concrete lined vertical shafts, 3 ea x 44.0 ft (13.4m) diam x 330 ft (100m) and 3 ea x 28.5 ft (8.7m) diam x 740 ft (226m), comprise a portion of the three underground power conduits. The project team decided to employ the slipform over the conventional jump form method. This selection was based on the engineer's hydraulic design and the contractor's performance requirements. This paper presents the key elements of the shafts' successful slipform operations. The contractor achieved slip rates as high as 60 ft (18m) per day; and the owner received competent permanent linings as specified by the engineer. The authors describe the team's effort to progressively improve both concrete quality and placement rate.

Jan 1, 1985

By Anthony R. Przybylek, John M. Visnesky

INTRODUCTION Thermal dryers have been utilized for reducing moisture of bituminous coal since the late 1930's. Since that time, numerous changes in the coal industry have motivated advances in thermal drying technology. The purpose of this paper is to discuss the changes that occurred to dryer design and focus on current practices of fine coal drying. The major topics discussed in this paper are: - Early Thermal Dryer Design and Evolution - Current Drying System Design and Associated Components - Current Economics of Fine Coal Thermal Drying - Future Markets and Design Considerations EARLY THERMAL DRYER DESIGN AND EVOLUTION Background The practice of drying fine coal with heated air has been performed for more than one half century. Throughout that period, both Metallurgical and Steam coal producers have used this method for reducing the surf ace moisture content of their fine plant products. During the late 1930's and early 19401s, vibrating bed and flash dryers were used to per- form the drying duties. Closed water circuits and vacuum filtration had not yet been integrated into process circuitry and centrifugal dryers were in their early stages of development. During that same period, changes in mining practices were reshaping the distribution of coal to our processing facilities. Plants originally designed for the purpose of processing coarser fractions of coal were being burdened with additional quantities of fine coal. Those plants, unable to recover fine coal, would reject these solids to plant bleed. The higher incidences of stream pollution that resulted from these events prompted clean stream legislation and the need for new, more efficient fine coal recovery circuits. The coal processing industry responded to these needs by integrating closed water circuits and filtration into circuits. The fine coal filter cakes recovered exhibited poor handling characteristics by themselves and often required further dewatering to improve their characteristics. Flash dryers at that time were being used to dry the coarser products. For those facilities operating flash dryers, the solution to this new problem appeared to be simple. The filter cake was combined with the coarser (-1/4") coal and then introduced to the flash drying column for drying. The filter cakes, however, presented significant problems for the flash drying systems. Heavy lumps of filter cake could not be dispersed and conveyed by the rising hot air and as a result would settle out in the bottom of the column. This material, known as "drop-out", would then accumulate and require further handling. The solution to this problem was not an easy one. Sophisticated mixing equipment was employed to condition the feed to the dryers. As attempts to minimize drop-out with this approach failed, the only recourse was to collect the material with conveying systems and recycle it back to the plant or dispose of it. The additional costs of handling this material reduced the attractiveness of the flash systems and opened the door for the development of a new, more cost effective coal drying system. Due to the nature of the problems experienced by the flash systems, fluid bed systems were considered. Fluid bed dryers were being used in other industries at that time but had no operating history in the coal industry. Dorr-Oliver transferred technology from other industries and built the first fluid bed drying system for fine coal.

Jan 1, 1988

By William Petruk

Volcanogenic base metal ores contain about 0.5 to 7 g/T Au, commonly as an intermetallic compound with Ag and/or Hg, and to a small extent • "invisible gold" in pyrite and arsenopyrite. The Au-bearing phase (electrum, Au-Ag-Hg alloy, etc.) generally occurs as fracture fillings in pyrite, arsenopyrite and chalcopyrite, and rarely • minute inclusions in pyrite and arsenopyrite. The Au-bearing phase in fractures generally occurs • small grains, and is frequently associated with galena, tetrahedrite and other late minerals. The gold is readily liberated from fractures and recovered by flotation in Ca concentrates. Copper concentrates usually recover around 60% of the gold when the ore grade is around 3 g/t. Higher recoveries are obtained for higher ore grades, and lower recoveries for lower grade ores. Lead and zinc circuits act as scavengers for gold, and recover all the exposed gold attached to small particles. Only unliberated gold, "invisible gold" and very minute gold grains attached to large particles are lost to tailings.

Jan 1, 1990

By James M. Prudden, E. P. Jucevic

The Divide mining district occupies the center of a Tertiary caldera hosting the famous Divide silver lode and the crosscutting Gold Mountain mines. The northwest-southeast trending silver lode hosted ore with typically a 100:1 silver:gold ratio, high molybdenum content and argillic alteration dated at 16.5 m.y. within the Fraction Tuff. The east-west trending Oddie Rhyolite flow dome at Gold Mountain experienced possibly several periods of resurgence with repetitive silicification, brecciation and attendant precious metal deposition forming stockwork type mineralization. Silver-gold ratios average 10:1 for the mineralization phase of this 16.4 m.y. intrusive event. Similar chalcedonic mineralization registering a 3:1 silver:gold ratio cements conformable breccias within the Oddie Rhyolite basal flows unconformably overlying the Siebert Tuff on the northern flanks of Gold Mountain. Gray and red chalcedonic breccia matrix in the King Tonopah member of the Fraction Tuff contains a 50:1 silver :gold ratio.

Jan 1, 1990

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By J. M. Applegate

In the same way that a blueprint communicates information about a structure, a useful systems architecture should provide information that guides the construction and implementation of computing systems. Taking the blueprint analogy a step further, a plot plan can also show where in the "bigger picture" a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: 1. The primary purpose of computer based systems relative to particular task or operation. 2. The relationship of systems to each other and an indication of their interaction and dependencies. 3. The relationship of systems relative to the organization and its objectives. 4. Indications of where IS/IT resources can best be allocated to support the organization. 5. The overall context in which new systems and technologies can be assessed for both their impact on current system and on the organization itself.

Jan 1, 1998

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By Steve Kral

It is agreed in mining and regulatory circles that a safe and healthy working environment for underground miners is the major challenge for mine operators. Underground mine ventilation is complex. And it is becoming even more difficult as mines become larger, deeper and more complicated. At the Seventh US Mine Ventilaton Symposium, a group of mine ventilation experts from industry, government and academia attempted to solve some of the problems in ventilating underground mines. The meeting, sponsored by the Underground Ventilation Committee of SME and the University of Kentucky, was held in Lexington, KY June 5-7, 1995. Andrzej M. Wala, symposium chairman, commented that previous mine ventilation symposiums have focused mainly on work in North America. The 1995 symposium, however, broadened its borders to include several international papers. Of the 77 papers presented and bound into the Proceedings volume, 25 are from operations and research centers outside of the United States and Canada.

Jan 1, 1995

By Fathi Habashi

CRYSTALLIZATION from aqueous solution is a simple and old method for the recovery of metal values from leach solution. Practically all the methods for the recovery of aluminum from clay are based on the crystallization of an aluminum salt from the leach solution. Differences in solubilities may be used to advantage for separating two metals from the same leach solution. The classical method of Marignac (1866), which makes use of the difference in solubilities of K2TaF7 and K2NbOF5 to separate niobium from tantalum, has been used successfully in the manufacture of these metals (Fig. 10-1). The slurry containing the metal oxides is dissolved in 70 % hydrofluoric acid, diluted, and heated near boiling. A potassium salt is added in sufficient quantity to form the complex fluorides of the niobium and tantalum present. The solution is filtered and allowed to cool. At room temperature most of the tantalum salt crystallizes out while the niobium remains in solution.

Jan 1, 1970

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By D. A. Ellis

This paper review s several new applications of solvent extraction developed in conjunction with a research project carried out under the AEC Raw Materials Division by the Dow Western Division laboratories during the last two years. A process for recovery of uranium from ores by contacting the solid directly with organic solvent without a prior aqueous leach and a process for uranium recovery by contacting thick, unfiltered leach slurry with the solvent were studied in an attempt to simplify ad reduce the cost of ore treatment procedures. Processes to produce pure UF4 products at the concentrate mills thus eliminating the production and subsequent dissolution of the concentrate were investigated. Since many of the leach liquors contained vanadium as well as uranium, solvent extraction processes for by-product vanadium were also studied.

Jan 1, 1958

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By B. Ceccarelli

Many public domain programs useful in mining engineering, e.g., MULSIM, DZTAB, and EXPAREA, require tedious data input and generate pages and pages of printed output. To eliminate the tedium and to enhance the output, ETI U.S., Inc. developed GEM, Graphics for Engineering and Mining, a collection of application programs and underlying interface tools for VAX/VMS computers. This paper presents an example of how an application program in GEM enhances a specific public domain program. It describes how GEM provides automated graphics assisted input and output. The paper describes how this program uses the GEM User Interface: the 3D GKS device independent graphics, server and drivers, various mining, mathematical and statistical algorithms, the means of handling graphics, data including IGES, and the foreign language interface.

Jan 1, 1992

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986

By E. F. ‘Pat’ Nelson, Richard Broom

Our portion of this afternoon’s session is dedicated to the operation of automatic process control associated with small to medium size primary or SAG milling circuits. In recognition of the subject matter of this symposium, specifically precious metals, our historical reference is Rosario Dominicanna in the Dominican Republic, one of the largest gold producers in the Western Hemisphere. Plus a backward glance to review very briefly the initial performance of the big primary mills at Island Copper in British Columbia and Pima IV in Arizona. We will then get to the subject at hand with a discussion of a retrofit control logic recently installed on a 5000 hp primary mill. The focus of this review is the simple, inexpensive, and cost effective character of this retrofit installation.

Jan 1, 1984