Search Documents

By Michael G. Nelson, Dot J. Helm, Edmond C. Jr. Packee

Under a Section 319 Water Quality grant from the U. S. Environmental Protection Agency, a working group of government agencies, mining industry representatives, and University of Alaska researchers undertook reclamation of an abandoned mine site on Birch Creek, near mile 101 of the Steese Highway. Stream hydrology, water quality, and the extent and nature of natural revegetation, were measured before the site was then recontoured to decrease the bedload deposition and bank erosion of the streams. Methods for stabilization of streams and rivers appear to have much in common with those for locations further south, but are subject to complications unique to the North, such as the formation of aufeiss, and to a lack of accurate climatological data. Natural revegetation appears to be possible for most northern placer mine sites. However, it may take place more slowly than required by public perception. Preliminary data indicate a surprising lack of nutrients in the floodplains of mined areas. Natural revegetation may be enhanced by selective planting of grasses and willows, which will contribute variously to soil quality, bank stabilization, and short-term appearance. Monitoring of hydrologic and water quality data, and of natural and artificially placed vegetation will continue at the .Birch Creek site through the summer of 1995,

Jan 1, 1995

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

Development of process control in the metallurgical industry over the past ten years has been highly influenced by technical advances centered on use of computers as well as on measurement and associated equipment. The discussion in this section reviews advances in computer technology, measurement devices, data input-output techniques, and their use in mineral processing for the objective of guiding application of process control principles. Advances in the next ten-year period through the 1980's can be foreseen in the cost and application of data handling facilities in the coincident fields of data processing equipment, interface and control devices, and computer programming systems. These will lead to greater acceptance in a widely expanding range of mineral processing fields. It can be predicted that process control methods now known to be effective will become more re- fined. Costs of on-stream analyzers for assays and particle data will be reduced. Continued innovation can be anticipated in measurement devices required for effecting control. Control techniques developed over the last decade in key process operations such as crushing, grinding, flotation, smelting, and hydrometallurgical processes are described in the following chapters. The general forms taken by computer process control are first outlined briefly.

Jan 1, 1979

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

Jan 1, 2006

By Steven J. Page, Robert A. Jankowski, John A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since initial verification of this health risk in coal mines by the Mine Safety and Health Administration (MSHA) during the early 1980’s, the Bureau of Mines has conducted numerous studies in underground mines to identify the sources of quartz dust and its fundamental characteristics. The most significant underground quartz dust source was found to be the continuous miner excavating rock. The percentage of quartz was also found to be higher in the smaller size fractions of the dust when significant amounts of rock was mined by the continuous miner. Furthermore, the quartz content in the continuous miner return remained fairly consistent at greater distances from the face. Another important factor speculated to affect quartz dust generation and its size characteristics is the morphology of the quartz bearing rock. The quartz content of dust between mines had notable differences with respect to the differences between kaolinite content in the dust. Low kaolinite content was associated with higher quartz content and increased size segregation of quartz into smaller dust particles, indicating that the free silica bonding matrix in the rock is most likely another factor responsible for quartz dust produced through mechanical comminution.

Jan 1, 1991

By C. E. Tackett

The Greenwich Collieries Co. is a subsidiary of the Pennsylvania Mines Corporation, and a wholly owned subsidiary of the PP&L Co. which serves the northeastern portion of Pa. PP&L annually consumes about 11 million tons of coal per year and is the largest consumer of both bituminous and anthracite coal on the eastern seaboard. Development work for Greenwich started in 1969. The coarse coal plant was constructed in 1970, with the raw fines bypassed. This worked very well for our requirements at that time; however, the Greenwich mining plans were extensively changed, longwall mining units were installed and low coal was encountered, resulting in dirtier coal, a finer coal and an ever increasing ash in the shipped product. All this demanded a more efficient ash removal process for the fine coal fraction. In 1971, the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency were pushing for the now stringent sulphur emission limits at our power plants. The Greenwich Mine coal reserves contained large quantities of 3.5 to 4% sulphur along with some low sulphur reserves. It was, therefore, essential that any new plant have the capability of efficient sulphur removal to meet the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency required limits. To meet these limits our design would have to be capable of producing a product of 2.0% sulphur or less.

Jan 1, 1977

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

Ever since A Decade of Digital Computing in the Minerals Industry was published in 1969, mining men have expressed the need for an additional reference on computer methods. It was felt such a volume should spell out the "how to" of computer applications in the solution of their problems. Computers in the minerals industry will be 20 years old when the 1979 SME Fall Meeting and the 16th International Symposium on the Application of Computers and Operations Research in the Mineral Industry (APCOM) take place jointly in Tucson, AZ. On such an occasion it was thought appropriate to publish an anniversary volume which reviewed current practices and projected what might prevail as computer methods for the future. Thus was born the idea to publish Computer Methods for the 80's. The first planning meeting for this volume took place in Las Vegas, NV, during the 1976 annual meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers. It quickly became evident that no single computer method existed to solve most mining problems; rather, mining computer methods are generally tailored to fit unique geologic, mining, and organizational conditions. Hence a format which included both the theory and practice for each of the computer applications was adopted for this volume.

Jan 1, 1979

Coal fly ash and flue gas desulfurization (FGD) sludges can be returned to mine pits, fills and revegetation zones in Virginia by regulation if (and only if) a positive beneficial use can be shown. Utilization of alkaline fly ash for control of acid drainage from pyritic coal processing waste piles, and use as a soil amendment for revegetation, are the two dominant beneficial uses proposed over time. Both applications must be controlled by the basic chemical properties of the ash proposed for utilization. Currently, public concerns over long-term As and Se leaching from various applications are increasingly driving regulatory options for mine site utilization. Many fly ash materials are relatively low in inherent alkalinity or neutralizing ability, and certain ashes are actually acidic. Failure to add sufficient total alkalinity will result in strong acidification of the ash utilization zones, stripping heavy metals like Mn, Zn and Cu from the fly ash matrix. Similarly, if alkaline ash is loaded into non-acid forming coal wastes at high rates such that leachate pH is > 9.5, significant leaching of As and Se has been documented in large scale laboratory leaching columns. Utilization of fly ash and FGD as a mine soil amendment for revegetation is based upon combined liming and water holding capacity benefits, however, levels of soluble salts (primarily sulfate and borates) limit one-time application rates to 100 Mg/ha or less.

Jan 1, 2006

By J. E. Brownhill

After being closed for three years, Specialty Minerals Inc.'s Port Inland limestone facility reopened in the spring of 1992 as a commercial limestone producer. In 1990, Specialty Minerals, a division of Pfizer Inc., bought Port Inland's reserves and equipment from Inland Steel because of the strategic value of the limestone for the production of precipitated calcium carbonate (PCC). Specialty Minerals' project team faced many challenges in reconstructing the Port Inland facility. Many traditions and norms had to be overturned to achieve the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. Port Inland's history Inland Steel built Port Inland in 1930. It was operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. The facility is located in the Upper Pen¬insula of Michigan on the north edge of Lake Michigan. Operations consist of a deep water port facility with crushing, screening and stockpile storage for 453 kt (500,000 st) of finished product at the port. Ninety-nine percent of the stone is shipped by lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical dolomite and limestone are produced on site.

Jan 1, 1994

By T. P. Weldum

INTRODUCTION Cleveland-Cliffs' operations in Michigan have been utilizing fully autogenous grinding for over four decades. This is but one of the key characteristics of the iron ore processing method that was developed for the extremely fine grained, low grade deposits of the region. Liberation size of the hematite and magnetite ranges from about 30 to less than 1 micron. Typical grinding fineness target to achieve silica grade in the concentrate is 80 to 90% passing 25 microns, or a P80 of approximately 20 microns. After primary grinding, the magnetite ore is first upgraded by rougher magnetic separation. It is then ground to final product size, sent through thickener-sizers utilizing selective flocculation, upgraded again by finisher magnetic separation, and then brought to final silica grade by reverse amine flotation. Hematite ore follows essentially the same route, less the magnetic separation stages. Concentrate is filtered and pelletized, along with con- trolled additions of fluxstone, to ready it for shipping. Iron ore pellets on the water of the Great Lakes have a value of approximately 1.5 cents per pound. GRINDING PROCESS DESCRIPTION Details of the Empire magnetite grinding process flowsheet have been presented by Greenwood and Rajala (1992), and more recently by Rose et al. (2002). The Tilden comminution process for either magnetite or hematite is essentially identical, with the exception of some variations in the excess pebble treatment methods (McIvor and

Jan 1, 2004

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

As orebodies being mined globally are of ever-decreasing grades, the focus on the concentration process has moved increasingly to the challenges faced in management of the gangue minerals. This is especially so in the flotation of platinum group minerals (PGMs), where head grades are typically in the region of 4–7 g/t. Hence, in PGM operations, a typical recovery of about 80 percent requires depressing about 85 percent of the gangue minerals. In a flotation cell the main control parameters are reagent type and dosage, froth depth and air addition rate. This paper reviews research projects carried out over an extended period aimed at optimizing the depression of gangue minerals: both those that are naturally floatable and those, such as chromite, that are entrained.  This has involved comparing the two major depressants used in the industry — guar and carboxymethylcellulose (CMC) — in the depression of the relevant gangue minerals, as well as investigating their consequent effect on the behavior of the froth phase. Because most PGM flotation plants treat the ore as if all the PGMs are associated with sulfides, copper sulfate is widely used as an activator, but this can also lead to inadvertent activation of gangue minerals. Finally, chromite levels must be kept below 3–5 percent to avoid any negative effects on smelter performance, and thus it is important to reduce chromite recovery which mainly occurs due to entrainment through, for example, froth depth control.   

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By Steve Karl, Rock Jenkins

Continuing its objective of sharing new ideas, methods, theory, and engineering developments, more than 550 members of the underground fraternity gathered in New York City for the 1985 Rapid Excavation and Tunneling Conference (RETC). Since the first meeting in 1972, RETC’S aim has been to lay a foundation of tunneling experience on which the industry could expand and develop over the years. The RETC is jointly sponsored by the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the American Society of Civil Engineers, in cooperation with the Canadian Institute of Mining and Metallurgy, and the Engineering Institute of Canada. The 17 sessions included 72 papers that explored up-to-date practices in the mining and civil engineering fields. Session topics ranged from geotechnical and seismic design, through design, construction, and support of underground openings, to ground water control in shafts and mine openings. Case histories of tunnel boring machines and large diameter tunnel and underground openings were also reviewed. All the papers presented at the three-day conference are valuable additions to improving the state of rapid excavation. A few sessions, however, are particularly noteworthy as they are geared to the mining industry. The two volume proceedings of the entire conference are available from SME. (See ad on page 1003).

Jan 7, 1985

By David T. Swanson

The term "pressure tunnel" in the broad sense includes all hollow spaces, aligned along an axis and surrounded by rock, which are suitable for pressurization. In particular, this category includes: • horizontal or slightly inclined water pressure tunnels; • vertical or inclined pressure shafts; • pressure chambers or shafts of surge chambers; and, • compressed air storage tunnels. The main problems in the design and construction of pressure tunnels result less from their length or size than from the requirement for watertightness and, dependent upon this, reliability in operation and economy in construction. Where the lack of sufficient overburden does not permit the rock to accept the internal pressure in the tunnel, or where this pressure is so high that the watertightness is in doubt although the stability of the tunnel shell is not in question, a pressure tunnel must nevertheless be reinforced. Surge chambers, pressure tunnels and tailraces which are subjected to relatively low internal pressure, usually not much in excess of 1.5 MN/m2, are eminently suitable for construction in post-tensioned concrete. Pressure shafts, which as a consequence of the high water head are subject to a considerable maximum service pressure, are usually lined with a steel tube, a considerable proportion of the internal pressure being transmitted to the rock by backing concrete. TYPES OF LINING FOR PRESSURE TUNNELS In general, the type of lining will depend upon the nature of the rock. As a result, pressure tunnels usually are not uniform in con-

Jan 1, 1981