Search Documents

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975

By Kan Aketa

The Japanese iron and steel industry has been developed remarkably, supported by the increase of steel demand. In particular, progress in various technical aspects of the ironmaking process, including burden materials, equipment, and operation has greatly contributed to the increase in productivity and the reduction of the fuel rate in blast furnaces. With the recent rise in the price of petroleum, the conversion of the energy source from oil to coke has resulted in a temporary increase in the fuel rate of blast furnaces.

Jan 1, 1982

By Ramarao Inguva

Feasibility studies being conducted to investigate the use of electromagnetic methods for insitu volumetric heating of oil shales will be discussed. A two dimensional numerical model which describes eletromagnetic heating of oil shales is outlines. The model includes equations for temperature, pressure, saturations, chemical reactions, mass conservation, and source terms. The gases are all assumed to form one bulk species and the oil is assumed to remain in liquid form. The chemical reactions include pryolysis of kerogen and char, release of bound water, coking, and decomposition if carbonates. Porosity and permeability are dynamic functions of the organic materials. Calibration of the model is accomplished by comparison of the model results with experimental data obtained by IITRI. Nonlinear relationships for viscosity, thermal properties, and source terms and used as inputs to the model. A finite difference approximation to the differential equations is derived and solved using Newton's iteration technique. For the cases studied the solutions are quite stable. Numerical resultes are included and a preliminary study of the optimization of the heating process is presented.

Jan 1, 1984

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. This study was made at the Mines Experiment Station of the University of Minnesota under the sponsorship of the Great Northern Railway Company. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semi- taconites and also the wash and heavy media ore types widely developed in the area. Each basic, original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type.

Jan 1, 1964

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By W. C. Morgan

The Federal Surface Mining Law enacted in 1978 is now being translated into regulations which must be followed in future coal mining. Substantial change to mining procedures is required to maintain stricter air and water control while mining and to return the mined out land to equal or better use than before. These changes do not come easy; and in most cases, they create a substantial additional cost. Based on field observations and mining studies, Caterpillar has been making suggestions on the use of their types of equipment to conform to the new standards at the least cost. This paper will be a brief review of some of the overburden stripping and reclamation methods suggested by Caterpillar. A production and cost comparison of dragline, scraper/dozer and truck, loader systems in 20 to 150 ft. Overburden conditions illustrates potential cost savings using mobile equipment.

Jan 1, 1980

By G. V. Borquez

For many years drilling and blasting has been considered more of an art than a science. This is still true in some respects, but today scientific approaches to drilling and blasting design must be used to plan an efficient operation which achieves desired fragmentation within constraints. These constraints involve minimizing damage to the wall or nearby permanent structures and avoiding undesirable fragmentation and mine dilution which can adversely affect operation costs. The degree of fragmentation by blasting is the most important single factor in any attempt to optimize the overall cost of the mining operations. The mining cycle begins with the drilling and blasting operations, which result in a given blasted rock size distribution. While this operation represents only about 20% of total mining costs, the efficiency and costs of the subsequent operations are strongly dependent on the fragment distribution obtained.

Jan 1, 1986

By R. Venkataramani

Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. Nearly 90% of all metals and-mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. 1 Constant efforts are needed to improve upon productivity if the ore is to be economically mined.

Jan 1, 1970

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By Atmesh K. Sinha

The demand for thermal coal both nationally and internationally is projected to increase rapidly. The marketability of high ETU thermal coal produced in the USA is, however, limited by its high sulfur content. Fortunately, over 70 percent of the sulfur exists in pyritic form. The research conducted at Southern Illinois University indicates that over 90 percent of the pyrite can be removed by simple devices such as concentrating tables, cyclones, or froth flotation cells and the desulfurized coal can be blended with low sulfur western coal to produce EPA compliance coal. Thus, both the low BTU western coal and the high sulfur midwestern coal can be rendered competitive in the utility markets, here and abroad due to improved utilization.

Jan 1, 1983

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By A. J. Erickson

In mid 1970, Park City Ventures, a Utah partnership of ASARCO and TAC, initiated a six phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration tar¬gets in several areas of the district. Discovery of ore in any of the target areas and continued favorable down dip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: Mississippian Humbug Formation replacement mineralization below productive ore bodies on the east flank of the Park City Anticline; Humbug replacement mineralization in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade Humbug replacement mineralization in a theorized structural block on the west flank of the anticline beneath the Ontario Vein; Permian Park City Formation replacement mineralization in the West End Shaft Area of the Silver King mine; vein mineralization along the Back Vein in the Judge Mine. Chilean Nationalization in 1971 resulted in a 30% budget cutback. The Judge and Silver King Projects were suspended. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure; five new ore bodies were found in the Humbug, and Doughnut Formations on the west flank of the anticline beneath the Ontario Vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1976

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By P. J. Lafforgue

In 1974- COGEMA (Compagnie Generale des Matieres Nucleaires) of France decided to exploit a uranium deposit discovered several years ago in a Permian formation of Southern France, near the town of Lodeve (Herault). The uranium occurs in black shales with high calcium carbonate content (7-10% CO2) and it was then necessary to use alkaline leaching. A fine grind (60-65% minue 270 mesh) was also necessary to obtain good' uranium recovery. A minimum of fresh water must be added to the alkaline system due to solution recycling. Filtration must be used because cake-washing requires less fresh water than countercurrent decantation.

Jan 1, 1982

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By Dave D. Ferris

Today the coal industry is beginning to use some very fundamental economic evaluations to determine the most economical circuit to produce a specified saleable product. The fundamental economic methods used are standard return on investment and net present value calculations. By utilizing these economical evaluations, one can justify a larger capital expenditure and realize more return for an investment over the life of a coal property.

Jan 1, 1983

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985

By Ernest B. Snyder

The word "line" has been used loosely for many forms of the common steel plant flux. For example, many people use the word "lime" for nigh calcium and dolomitic limestone, for high calcium and dolomitic quicklime (also called caustic lime, calcined lime; burnt lime, pulverized and pebble lime) and ;van for clinkered dolomite. Calcium hydroxide, also called slaked lime and hydrated lime, is called "lime" but is seldom used as a flux except when the quicklime air slakes in open boxes or bins. All of the above forms of "lime" are used in the steel plant. Calcium hydroxide is used for water treatment, acid neutralizing, and as a lubricant for wire drawing. All the other limes are used as fluxes in the sintering plant, blast furnace or steel producing furnaces. In the production of self-flux or super-flux sinter, high calcium and dolomitic limestone fines are used. Where quicklime fines are available, they may be added to the sinter mix also. The blast furnace uses both high calcium and/or dolomitic limestone. A few trials have been made using iron oxide stabilized dolomitic lime in an attempt to reduce coke consumption and to increase the production rate. The trials were very successful but would' not be economical, except in periods of coke shortages, with resulting extremely high coke cost and exceptionally high hot metal demand.

Jan 1, 1979