Search Documents

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By R. R. Odman

The Malmberget Division of LKAB is located 70 km north of the arctic circle and has about 2000 employees. The dominating products are sinter feed concentrate and pellets. A general flow sheet for the operation is shown in Figure 1. About 20 percent of the ore body consists of hematite, which is mined separately and processed into sinter feed concentrate. That pert of the ore consisting of magnetite passes through a dry cobbing plant. The robbing process includes crushing, screening and dry magnetic separation. The entire cobbing product is used as feed for the wet concentrator. After rod mill grinding and magnetic separation the concentrated slurry is classified. The coarse fraction (+200 mesh) becomes sinter feed concentrate and the slime fraction after further ball mill grinding and magnetic separation, becomes pelletizing feed. A small quantity of the magnetite ore is processed into special iron-rich products in the the wet concentrator. Two types of pelletizing plant are used, shaft furnace and straight grate. This paper will deal only with experience gained at the straight grate plant.

Jan 1, 1979

By Roy J. Greenfield

A highly undesirable side effect of the mining of coal is the release of acid forming chemicals into the ground water system. The disturbance of the ground during mining allows water to flow through the coal bearing strata and mine refuge where it absorbs iron and sulfide ions and thus becomes highly acidic. The highly acid mine water can then contaminate water supplies and can destroy many of the recreational uses of Pennsylvania's waterways. A great deal of effort has been expended to develop methods of controlling groundwater pollution from mine drainage. At the Pennsylvania State University there has been an ongoing effort to under- stand the chemistry of acid mine water formation and the hydrologic environment in which the acidic water migrates from the mine source into the ground water system. As a support to the hydrologic studies, geophysical studies have been used to help determine the geologic structure of the areas under study which are contaminated by acid water. In addition, the geophysical work has been used to define the type of information geophysical methods can give to determine which geophysical methods are most useful and to develop geophysical field procedures.

Jan 1, 1973

By L. Frost

The establishment of a retreat system of longwall mining in this submarine coal field has been under study for many years and, although in special cases there have been limited local applications of this method of mining, there has been no attempt until quite recently to establish a uniform system of longwall retreating' in this area (see Figure 1) Where retreat walls were established, it was strictly as a result of physical, rather than economic conditions. In some of the operations- of the Corporation, where the coal was liable to spontaneous combustion- or the area subject to bumps as in No. 2 Mine of the Cumberland Railway and Coal Company in Springhills the recovery of the coal on a retreat system was more or less a necessity.

Jan 1, 1964

By J. P. Matoney

The operation of a modern coal preparation plant, particularly in western Canada, is a very complex task. Most western Canadian operations are processing two or more, sometimes up to ten, different seams through the same plant. This requires a sophisticated multi-circuit plant that needs close operational control. Add the soft nature and large amounts of natural fines of western Canadian coal and you have a formidable cleaning task. To assist in the operation, programmable controllers and sophisticated control concepts are being more widely used. Two of the newest coal preparation plants in Canada have been designed by Raymond Kaiser Engineers Inc. and its Canadian subsidiary, Phillips Barratt Kaiser Engineering, Ltd. The use of programmable controllers and control systems will be illustrated by showing their application in a "typical" western Canadian coal plant. This example will cover flowsheet design, control concept systems application, and possible future uses.

Jan 1, 1983

By Paul Soros

The rationale for innovations in two directions is identified: raising capital and annual throughput, in order to avoid the cost of constructing and operating an additional system and to reduce the capital cost of pits and tunnels, applicable to installations of any capacity. Cast histories cover railroad unloading of bottom dump cars, rotary dumping of random cars, with and without indexer, and unit trains as well as truck unloading of multiple grades of coal.

Jan 1, 1985

By M. A. Klugman

[This paper represents a portion of a lager study, concerning dispersion patterns of major, minor and trace elements in wall-rock about ore-bodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to ore-bodies in two mines of the Alma-Horseshoe Mining District of Central Colorado. The mining district is located 80 miles southwest of Denver (Figure 1) on the east flank of the Mosquito Range. The area is typified by rugged relief with altitudes from 10,500 to 14,000 feet.]

Jan 1, 1962

By E. G. Loesche

Grinding mills in which the comminution takes place between rollers and the surface of a disc, table or ring are generally known as roller type mills. The Loesche Mill, also known as the Disc Roll Mill, is a special type of roller mill in which the grinding surfaces consist of two rollers assembled over a horizontal disc or table which rotates at a relatively low speed. This design is particularly applicable to industry's present day demand for large capacity grinding mills.

Jan 1, 1964

By H. B. Comstock

This paper reviews the trends in supply and consumption of the principal magnesium compounds in the United States in relation to domestic requirements and world resources. The data are confined to these principal magnesium compounds: Magnesium chloride, magnesium hydroxide, precipitated magnesium carbonate, and magnesium oxide (commonly referred to as magnesia). The properties and uses of magnesium compounds are shown in various chapters of' the 2nd edition of Industrial Minerals end Rocks. 3/ The third edition of this reference is in preparation. A more recent description of properties, uses and sources of magnesium compounds appears in a Bureau of Mines publication.4/ The American Iron and Steel Institute and the Refractories Institute have published comprehensive data on the properties and uses of basic refractories. Many magnesium compounds are prepared by the producers to meet specifications set by individual consumers.

Jan 1, 1960

By G. C. Knutsen

The Post deposit is located in Eureka County, Nevada, about 37 km (23 miles) northwest of the town of Carlin. Post occurs on the Carlin Trend, a northwest alignment of 14 major gold deposits, each containing more than three tonnes (t) (100 000 ounces) of gold. Deposits of the Carlin Trend are epithermal, sediment-hosted, disseminated gold occurrences, collectively containing more than 622 t (20 million ounces) of gold. Three major gold producers active on the Carlin Trend are Newmont Gold Company (NGC) (12.4 t/400 000 ounces of gold per year), Western States Minerals Corporation (WSMC) and Pancana Minerals joint venture (1.56 t/50 000 ounces of gold per year), and Dee Gold Mining Company (1.4 t/45 000 ounces of gold per year). The Carlin Trend has also been referred to as the Lynn-Railroad Mineral Belt. This district is characterized by open-pit mineable, micron-sized gold, hosted in Paleozoic sedimentary rocks. Six geological subdistricts comprise the Carlin Trend, each characterized by differences in host lithology, structural controls, alteration assemblage, or style of mineralization. The six geologic subdistricts include, from south to north, Bullion (Railroad), Rain, Maggie Creek, Lynn, Bluestar-Goldstrike, and Bootstrap. With the exception of the Bullion subdistrict, which was primarily a producer of base metals, each sub-district contained mineable reserves in excess of 31 t (one million ounces) of gold.

Jan 1, 1987

By M. Dosemeci, M. McCawley, J. McLaughlin, Z. Wu, F. Hearl, W. Blot, K. Peng

Proposals have been made by two organizations, the International Standards Organization (150) and the American Conference of Governmental Industrial Hygienists (ACGIH) for a revised respirable dust criteria and criteria for thoracic and inspirable dust. These criteria yield different results than criteria based on lung deposition patterns in assessing the hazards due to dust exposure. Since these differences are a function of the size distribution of the dust an analysis of dust size distributions from various mining operations was performed to determine the amount of difference that could occur. The dust size distributions available for this analysis were taken from U.S. coal mines and from Chinese metal mines. The mass of mechanically generated dust that will deposit in the alveoli was found to be in direct proportion to the ISO/ACGIH criteria estimates in the mines studied. Therefore, respirable dust estimates for substances such as coal and silica are not a problem. Estimates of exposure to diesel exhaust in these mines, however, were not always in the same proportion to the estimated alveolar deposition. Also, concern with an excess of bronchitis among miners may not be adequately addressed by the use of samplers conforming to the ISO and ACGIH criteria. The cascade impactors used to acquire the data for this analysis require four to eight substrates per sampler. For daily dust exposure assessment this method is cumbersome and time consuming. Therefore, two new samplers have been designed to meet the need for determination of deposited dust mass. These samplers follow the lung deposition curve rather than the penetration curves proposed by the ACGIH and ISO and require analysis of only two substrates per sample.

Jan 1, 1992

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines.

Jan 1, 1981

By A. M. Gaudin

In a recent paper we have reviewed principles and applications of measurement methods for contact angles and their hysteresis (22). In this paper we apply these methods to a system consisting of rutile, an organic liquid (benzene, decane, or dodecane) and water. Surfactant (dodecylamine hydrochloride) was used at various concentrations and various pH values.

Jan 1, 1964

By J. M. Mutmansky

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem --using properties of the system characteristic curve for a two-terminal network --and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By K. K. Wu

In some cases, coal barrier pillars must be relied on to withstand high hydrostatic pressures in order to prevent inundation of active mine workings. Such barriers are particularly important in areas, such as parts of West Virginia, where much of the future mining is down dip of mines which have been abandoned, or are currently being worked. Also, where multiple seam mining is conducted, a barrier pillar in one mine may be critical to safety in a mine in a lower seam. MSHA's Coal Mine Safety and Health district offices and the Mine Waste and Geotechnical Engineering Branch of the Pittsburgh Technical Support Center, have recently been involved in the study of barrier pillars in Kentucky, Virginia, West Virginia, Ohio and Oklahoma. In this paper, the factors involved in determining the required width of pillar are discussed, past practices for sizing barriers are reviewed, and related current Federal regulations are examined. In addition, the results of laboratory testing of bottom rock are presented.

Jan 1, 1980

By W. H. Reck

he need in the mineral industry to treat increasingly larger tonnages has caused a demand for larger installations. In order to limit the size of these installations, it was necessary to build machines with larger capacities or production output. With this aim in mind, WEMCO Division developed the No. 120 WEMCO-Fagergren Flotation Cell in 1967. These large cells have been compared to conventional smaller cells from the standpoint of metallurgical performance, investment costs, power requirements and maintenance requirements in many plants throughout the world. Figure 1 illustrates the size difference of the No. 120 when compared with the No. 66. All results to date indicate the large No. 120 cell surpasses the smaller machines in all categories.

Jan 1, 1969

By R. W. Utley

Over one half billion tons of coal per year is scalped, classified, deslimed, drained and rinsed, dewatered and final sized on rotary, vibrating, shaking or stationary screens. The vibrating screen is the industry work horse and performs the bulk of the screening functions in the coal preparation plant. There are two major types of brute force mechanical vibrating screens used in coal preparation plants: (1) the two-bearing one-shaft inclined screen and (2) the four-bearing two-shaft horizontal screen. Both of these types are familiar to coal producers.

Jan 1, 1966