Search Documents

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

One of the problems associated with the maintenance of roadways in underground coal mines is that of dealing with roadway closure. Sidewall weakening technique is based on the transference of the high stress zone further away from the vicinity of roadway. This transferral is carried out by weakening parts of sidewalls of roadway by cut- ting slot, drilling a series of parallel holes or blasting during development stage. In the paper, the effect of sidewall weakening on the stability of roadway is studied by finite element analysis and field experiment. The finite element analysis shows that sidewall weakening can control the development of yield zone around a roadway, improving the stability of roadway. It is also shown that if in- situ horizontal stress is lower or higher than the in-situ vertical stress, it is difficult to obtain roadway stability by sidewall weakening. The field experiment shows that roadway closure can be controlled by sidewall weakening with blasting.

Jan 1, 1990

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By Robert W. Bruhn

An investigation was male of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at nine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the nine height ad continued more than a year after mining. Water levels declined la certain deep-lying strata.

Jan 1, 1984

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000