Search Documents

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Shaohua Ju, Feng Jiang, Chuanhua Li, Jinhui Peng, Libo Zhang

A T-junction microchannel is proposed to overcome the existing problems in conventional solvent extraction of indium from zinc hydrometallurgical process. Experiments were performed to separate In3+, Fe3+ and Zn2+ from sulfate solutions using Di-(2-ethylhexyl)phosphoric acid (D2EHPA) as the extractant. The effect of parameters such as pH, microchannel size and contact time on the extraction behavior of In3+, Fe3+ and Zn2+ was investigated. At contact time of 2.52 s and initial solution pH of 0.48, the extraction efficiency of In3+, Fe3+ and Zn2+ was 99.13%, 8.31% and 2.45%, respectively and separation factor of In3+/Fe3+ and In3+/Zn2+ were almost 1229.54 and 4864.98, respectively. Then, the loaded organic phase was stripped in T-junction microchannel. At contact time of 33.6 s, 99.64% of stripping efficiency of In3+ and stripping equilibrium were reached, while concentration of Fe3+ and Zn2+ was lower than 0.01 g/L with good separation of In3+ from Fe3+ and Zn2+.

Jan 1, 2016

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By T. L. Baum

External oxidation during in-line heat treatment of TRIP steels can cause problems for the subsequent coating process. This research aims to elucidate the kinetic rates of internal oxidation, external oxidation and decarburization and their interdependence under different gas atmospheres and temperatures. A rolled steel sample chemistry of 0.14 wt.% C, 1.8 wt% Mn, 0.6 wt.% Si and 1 wt.% Al is used as a case study. Thermogravimetric techniques are used to examine the net mass change in a sample during heat treatment and the results show an initial mass decrease and later an increase for particular partial pressures of H2O. SEM-EDS, optical microscopy and glancing-angle x-ray are used to quantify the microstructure. The cross-section of the samples have 4 distinct zones: (i) an external scale, rich in fayalite, (ii) an internally oxidized region with Al, Si and Mn oxides in an Fe matrix, (iii) a decarburized steel region, characterized by large ferrite grains and low carbon content, and (iv) a relatively unaffected steel core with a structure similar to the starting material.

Jan 1, 2006

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

By Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"Fine manganese fines are characterized by large amount and low price compared to lump manganese ores. However, fine manganese must be agglomerated as EAF (electric arc furnace) feed. In this paper, high quality fired pellets were produced by simulating grate-kiln process to supply the feed for EAF from some imported manganese ore fines containing high combined water. Manganese ore fines assaying 44.47wt%Mn, 5.89wt%Fe, 12.09%LOI and with 72.7wt% ranging between 0.5mm and 8mm, are pretreated up to the particle size of 84.7wt% passing 0.074mm by HPGR (high press grinding roller) twice in open circuit. The finely ground manganese fines were mixed with 1.2wt% bentonite, balled at 15% moisture for 7min in disc pelletizer. The drop numbers, compressive strength and thermal shock temperature of green balls reach 11 times/0.5m, 11 N/pellet and 360oC, respectively. After the green balls drying in the oven, the dry pellets were preheated at 1050oC for 12 min and then fired at 1300oC for 12 min in electric tube furnace. The compressive strength of fired pellets reaches 2621 N/pellet. Therefore, these pellets are high quality burden for blast furnace or EAF due to high mechanical strength and high Mn grade of 49.11wt% and low detrimental elements.IntroductionManganese, mainly using as deoxidizing agent, desulfurization agent and alloying elements, is widely used in the steel company. With the rapid development of iron and steel industry in China, domestic manganese ores cannot meet the requirement, resulting large quantities manganese ores import to China [1-4]. Compared to lump manganese ores, fine manganese ores containing high combined water are characterized by large amount and low price. However, they must be agglomerated as EAF (electric arc furnace) feed. There are three ways to agglomerate the manganese fine ores, sintering, briquetting and pelletizing [5-6]. Compared to the other two methods, pelletizing technology possesses the following superiorities, such as uniform size distribution of product, stabilizing chemical composition of product and lower energy consumption in producing. Therefore, pelletizing is a superior way to treat the fine manganese ores [7]. The systematic research of producing manganese oxide pellets by fine manganese ores containing high combined water was studied in this paper."

Jan 1, 2011

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP'd, HIP'd, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By Qian Xu, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Shuhua Geng, Hongwei Cheng

Herein we report an electrochemical route from oxides (SiO2, TiO2)/sulfide (MoS2)/carbon mixture precursors to Mo-Si-Ti-C composites in molten salt. The electrochemical process was carried out in molten CaCl2 at 800 °C with a potential of 3.1 V, and a graphite-based anode was used in the electroreduction process. The reaction mechanism and the influences of the stoichiometry of the initial mixture precursor on the morphology and phase composition of the final products were investigated. It has been found that Mo5Si3/MoSi2/Mo3Si/Mo, Mo5Si3/MoSi2/Mo2C/SiC, and Mo5Si3/Mo2C/Ti3SiC2/TiC/Mo composites can be electrosynthesized directly from their oxides/sulfide/carbon mixture. The preliminary experimental results suggest that the electroreduction process can be used for the controllable electrolytic production of alloys/carbide-containing composites from oxides/sulfides/carbon precursors.

Jan 1, 2016

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Yun Soon Han, Joo Hyun Park

Indium (In) solubility in the FeO-SiO2-Al2O3-5%CaO slag was measured under p(O2)=10¯¹¹ atm at 1573 K to clarify the dissolution mechanism of In in FeO-bearing metallurgical slag. The In solubility increased with increasing oxygen partial pressure, whereas it decreased by increasing the activity of basic oxide, viz. FeO. Thus, a dissolution mechanism of In in the FeO-SiO2- Al2O3-5%CaO slag was described by the following equation. In(s)+1/4O2(g)=(In+)+1/2(o2-) The enthalpy change of the In dissolution reaction was negative, indicating that the dissolution reaction was an exothermic reaction. This is consistent with the above reaction mechanism.

Jan 1, 2014

By Masatsugu Morimitsu, Tian Zhang

"This paper presents a novel anode for oxygen evolution in acidic aqueous solutions to produce non-ferrous metals by electrowinning. The method to prepare the anode was thermal decomposition of a precursor solution, and the obtained anode consisted of Ru02-based oxide catalytic layers formed on a titanium substrate, in which the catalytic layer contains nano-oxide particles as the active component. The oxygen evolution potential was lower than amorphous lr02-Ta20s coated titanium anodes so that the cell voltage of electrowinning was further reduced with the amorphous Ru02-based electrode.IntroductionElectrowinning (EW) is used to produce high purity of non-ferrous metals, and the primary metal production of copper, zinc, nickel, and cobalt by EW consumes huge electric energy worldwide, which tends to increase with increasing demand of such metals. The reduction of electric energy consumption is a significant issue for electrowinning industry, which means that the cell voltage reduction is needed to realize more energy-efficient EW processes. Another issue is also indicated from environmental perspectives; i.e., an improvement in EW plant environment by eliminating hazardous byproducts and wastes. Such byproducts and wastes include lead oxide, manganese oxide, and acid mist.We have been developing the anodes for energy-efficient and environmentally friendly electrowinning processes [ 1-11]. The development has been successfully done with the invention of the smart anode, MSA TM (Morimitsu Smart Anode) [ 1-5], which has low polarization for the main reaction and high polarization for the side reaction, in which the main reaction is oxygen or chlorine evolution, while the side reaction is the anodic deposition of each or both of lead oxide, manganese oxide, and cobalt oxide. The anode consists of a valve metal substrate coated with amorphous or less crystalline oxide catalytic layers. One of the typical examples of such oxides is amorphous lr02-Ta20s, and the substrate is normally titanium plate or mesh. The most important point of the oxide is that the amorphization or less crystallinity induce the increase in the active surface area only to the main reaction, not to the side reaction, thereby the polarization of the main reaction being reduced.In this paper, we present the smart anode consisting of RuO2-based catalyst formed on titanium substrates for oxygen evolution in electrowinning. The preparation, characterization, and polarization behaviors of the anodes are shown, and the cell voltage data for zinc or copper electrowinning using the anodes are also presented."

Jan 1, 2012

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011