Search Documents

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By A. Valenzuela

During the last years, Chile has been the largest copper producer, either as concentrates or cathodes. Copper obtained via pyrometallurgy is produced by seven smelters, which have carried out modernization plans to increase smelting capacity or to achieve environmental regulations established in the Chilean legislation. Thus, the present work updates technological innovations in smelters, environmental regulations and presents solutions for SO2 handling, particulate matter and arsenic. Also, the authors emphasize the important role of CODELCO Chile, the most important state-owned copper company, in developing technologies such as EI Teniente Converter and EI Teniente Slag Cleaning Furnace,

Jan 1, 2003

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By Dilek Kirgöz, Onuralp Yücel, Murat Alkan

"In this study, Mo containing Fe-based alloys, such as Fe-Ni-Cr-Mo, were synthesized using a mixture of Fe203-NiO-Cr203-Mo03 powders reducing with Al powders by metallothermic process which is a high energy efficient, fast and low-cost production technique for synthesis of cast alloys and advanced ceramics. Detailed thermochemical studies were simulated by using FactSage 6.2 Thermochemical software in order to calculate adiabatic temperature of the reactions and effects of initial molar composition on the final products. In the metallothermic processes, effects of stoichiometric Al addition and addition of the oxide powders (Alz03, Si02, CaO, MgO) on the metal recovery and compositions of final alloys were carried out. Final products were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Fe based alloys (Fe-Ni-Cr-Mo) which are used as surface coatings, wear-corrosion-oxidation resistive applications via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By QIE Jun-mao, DONG Fang, DENG Hao-hua

The DIL402C thermal dilatometer and STA449C thermal analyzer were employed to test the linear expansion and contraction coefficient，CP and DSC curve of 304 stainless steel. The result showed that the linear expansion coefficient range was 20.9700×10-6～21.5712×10-6 and the linear contraction coefficient range was 21.2528×10-6～21.9471×10-6.The linear expansion and contraction coefficient were higher than other steel grade，so the 304 stainless steel belonged to the crack sensitive steel. Because of the crystal phase transformation occurred during the 1000~1400 ℃,the curve of CP fluctuated obviously and the defects of casting blank occurred easily. Chosen 1414℃ as the liquidus temperature of 304 stainless steel based on the analysis results of DSC. The curve of DSC was unsmooth during 1450～1100℃，the crystal phase transformation occurs and thermal stability of slab was inferior.When the initial solidified shell formed in this temperature range,the thickness of the shell would be nonuniform and the surface defects occurred more easily.

Jan 1, 2015

By Marcelo Mourao, Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano

"The self-reduction is an alternative and promising process for production of pig iron because offers decisive benefits such as enhancing the reaction kinetic with decrease in fuel consumption and C02 emissions. The self-reduction mixture of iron ore fines, carbonaceous reducer and additives for slag forming components, without agglomeration, was tested in a laboratory rotary kiln. The additives for slag were defined for presenting two different estimated liquidus temperatures (1623 Kand 1773 K) to verify the effect of these temperatures on the iron-carbon nuggets coalescence process. These mixtures were tested at 1673 and 1773 Kin an experimental rotary kiln. After reduction-melting and coalescence processes the samples were disaggregated and the iron nuggets were classified by size. It was considered that nuggets larger than 7,93mm would be a good reference for coalescence index. Low liquidus temperature slag presented 37% of this larger fraction against only 13.5% for high liquidus temperature one. The low liquidus temperature slag would facilitate contact between the particles of iron-carbon in a rotary kiln, enhancing the coalescence.IntroductionThe slag composition usually depends on the reducer ash composition, the ore gangue, the binder composition and any fluxing material [l], and the mechanism of carbon transportation in slag that contains iron oxide reducible by carbon can be explained by the oxide reduction and the metal carburization. During carbon transportation, the carburized particle is transported to slag-metal interphases by the gravity effect, being assimilated by the metallic phase [2]. When the slag's iron oxide comes in contact with the solid carbon, it is immediately reduced, forming Fe particles and CO bubbles as it is shown in the figure l(a). The Fe particles are carburized by carbon particles; they are liquefied simultaneously in the carbon-slag interphase. The Fe-C liquid particles are transported from the slag-carbon interphase to iron-slag interphase as a result of slag flow, based on the surface tension difference (Marangoni effect), figure l(b). The Fe-C liquid particles coalesce on the iron surface and the carbon is immediately diffused in the iron as it is shown in figure l(c). The reduced iron is carburized continuously by repeated sequences [3]."

Jan 1, 2013

By M. S. Moats

The treatment of oxidized residues of zinc with high iron content continues to present a technical challenge in both the steel and zinc industries. Two main problems are commonly identified and include high treatment costs and environmental concerns about contaminated, iron-bearing residuals. A new approach to this problem is described in which selective separation of the iron and zinc into salable products may be potentially feasible. The waste material is first leached to give a solution having an approximate concentration of 110 g/l Zn, 15 g/1 Fe and 40 g/1 H2SO4 and other impurities such as Pb, Cd, Cu and Sb. A suitable organic, such as D2EHPA, is used to load the majority of the iron. The aqueous phase is then acceptable for zinc electrowinning after standard solution purification. The novel step in the flow sheet is the efficient recovery of the ferric iron from the organic solvent using a solid metal to reduce the iron to the ferrous state. The Fe+2 is easily stripped into an aqueous phase in a relatively pure form, suitable for use in water treatment. Process parameters and possible flow sheet designs are described and discussed.

Jan 1, 1995

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014

By Leonard J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been an effective means of reducing sulfur dioxide emissions from non-ferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2006 previous works on metallurgical sulfuric acid plants by the authors.

Jan 1, 2006

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By Jie E. Zhou, Yu U. Wang

"Development of crystallographic texture in polycrystals during templated grain growth process is studied by phase field modeling and computer simulation. To characterize the grain texture development, X-ray diffraction peak intensities are computed for the evolving grain structures as simulated by the phase field model, based on which Lotgering factor is further calculated as a quantitative measurement of uniaxial texturing. While the phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations, the computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, since microscopy experiments normally require more efforts than X-ray diffraction, and diffraction is usually the preferred choice for material characterization.IntroductionThe properties of individual grains in polycrystals are generally anisotropic, while untextured polycrystalline materials with random grain orientations exhibit isotropic macroscopic properties that are independent of directions. In order to achieve anisotropic response in polycrystals, crystallographic texturing of grains is required [1]. Texture refers to the collective distribution of grain orientations towards preferred orientation in a polycrystal. To develop texture, special processing routes are needed, such as templated grain growth (TGG) for uniaxial texture [2]. TGG has been shown to provide uniaxial texture in wide variety of materials. For example, [001]-textured ferroelectric polycrystalline ceramics have been fabricated by TGG process, which exhibit enhanced piezoelectric properties [3]. Such highly textured polycrystalline materials offer better cost-performance ratio than single crystals. Thus, texture development in polycrystals is of technological importance for material applications.In this computational work, grain texture development in polycrystals during TGG process is studied. Grain structure evolution is simulated by phase field model, X-ray diffraction peak intensities for the evolving grain structures are computed, and Lotgering factor is calculated to quantitatively measure the development of uniaxial texturing. The phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations using imaging techniques such as scanning electron microscopy or optical microscopy. The computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, because microscopy experiments normally require more efforts than X-ray diffraction, thus diffraction is usually the preferred choice for material characterization."

Jan 1, 2014

By M. E. Myers

An experimental program is being carried out to determine the thermodynamic characteristics of zinc solubilization in high-temperature iron and iron-carbon alloys. Two versions of an isopiestic technique are being used, with zinc at a lower temperature being equilibrated with pure iron foils or molten iron-carbon alloys at a higher one. The lower temperature sets the partial pressure of zinc vapor, and thus the activity relative to a given reference state. Initial results show Henrian behavior for dilute zinc solutions in austenite and a molten 4.6% C alloy, with unit-pressure solubilities in pure Fe that closely match the predictions of Wriedt.

Jan 1, 1992

By Francois Barthelat, Sam Goroshin, David Frost, Alexander Cappozi, Atefeh Nabavi

"In this study, a novel chromium–chromium sulfide cermet was produced by self-propagating high-temperature synthesis (SHS). Conventional techniques for manufacturing metal sulfides are complex, environmentally harmful, and not suitable for producing complex-shape articles. To overcome these disadvantages, a new method for the preparation of the metal-sulfur precursor charge is proposed, which can be described as reactive casting. The first cermet samples produced with the SHS process were found to be very porous, brittle, and have low mechanical strength. The possible sources for the generation of porosity were identified and analyzed and the process for manufacturing the cermet was modified. By improving the manufacturing process, the porosity inside the produced cermets was reduced from 70% to 12%.IntroductionMetal sulfide composites are in high demand in the chemical, metallurgical, and electrical industries because of their valuable characteristics such as hardness, semi-conductivity, electroluminescence, infrared transparency and catalytic properties. Current manufacturing methods for metal sulfides usually involve one of two different principal methods, including a complex multistage wet chemical process involving the precipitation of the corresponding salts from an aqueous solution with hydrogen sulfide, or hot sintering of the respective elemental reactant powders in a resistive furnace in a high-pressure inert or hydrogen-sulfide atmosphere [1, 2]. These conventional methods for synthesizing ceramic metal composites are complex, extremely time and energy consuming, environmentally harmful, and rarely able to manufacture articles with complex shapes. Therefore, in order to overcome these disadvantages, self-propagating high-temperature synthesis (SHS) was considered as an alternative method that offers significant improvements over the traditional cermet manufacturing methods [3]. SHS, which is a relatively new and attractive method for producing a wide range of advanced materials, is based on the self-sustaining feature of the highly exothermic reactions of the reactants. The SHS process results in high product purity, since the high temperatures generatedin the reaction cause any impurities to volatilize [4, 5]. SHS has low energy consumption and doesn’t require an external energy source and complex equipment, and it is self-contained [1, 5]. Since combustion synthesis has low power requirements, it is one of the few methods of materials synthesis that is feasible in outer space. Also, the process has a low cost and is capable of directly synthesizing articles with the desired shape, size and structure [5, 6]. The chemical reactions associated with SHS are typically completed in a few seconds leading to the formation of the condensed product. The high reaction rates and relatively rapid cooling in SHS reactions can avoid undesirable grain growth in products which often occurs with the conventional sintering method [3, 5, 7]. The traditional method for sample preparation in the SHS technique is to compact the reactant mixture powders in a steel die by a press to a typical density of about 80% of the theoretical maximum value, before igniting the mixture [8]. This method requires a large compression force to increase the green density and to minimize any pores in the green compact. To overcome these disadvantages, a new method for the preparation of the precursor charge in metal-sulfur by SHS is proposed which can be described as melt casting of a reactive mixture, or reactive casting in short."

Jan 1, 2012

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983