Search Documents

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30tlhour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By Hüseyin Aydin

TWIP (Twinning-Induced Plasticity) steels have exceptionally good combinations of strength, ductility and damage tolerance which satisfy the recent requirements of automotive industries. Firstly, TWIP has the most beneficial effect on the work-hardening. It is believed that deformation twins increase the work-hardening rate by acting as obstacles against gliding dislocations. Moreover, TWIP steels have low to intermediate stacking fault energy and hence undergo extensive mechanical twinning during deformation, which in turn leads a good combination of both strength and ductility. To explain the mechanical characteristics and the mechanical behavior of the TWIP steels, we have been made some investigations and experiments that show the effects of microalloying elements and deformation mechanisms. In this study, three different compositions of TWIP steels have been produced. The microstructure and mechanical properties are characterized by using optical, electron microscopy and mechanical tests.

Jan 1, 2009

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By Honggang Zhong, Tan Yi, Qijie Zhai, Zhao Dan, Xinping Mao, Huigai Li

"The influence of superheat degree on the distribution and volume content of inclusions were studied in 65Mn thin slab produced by compact strip production(CSP) in Zhujiang Steel in China, The results showed that the diameters of inclusions are mainly less than 5µm. Most of the inclusions gathered at the 1/4 thickness direction for the thin slab of 27? superheat degree, compared with the center position for that of 37?. There are more inclusions larger than 50µm in the low superheat samples, which is caused by the short floating time. In addition, the inclusions were observed and analyzed by metallurgical microscope, SEM and EDS in order to ensure their composition, type and further find their source. It was find that the types of these inclusions mainly are Al2O3, SiO2,CaO and their composites, a few of them are TiN and MnS.IntroductionIt is well known that inclusions have a great impact on the strength, plasticity, fracture toughness, cutting performance, fatigue property and corrosion resistance of steels. Especially, with the demand for thinner slab, the cleanness is increasingly becoming more significant as a quality criterion[1]. High manganese and carbon steels not only demonstrate high strength but also proper plasticity. There are many problems unsolved for 65Mn steel as a result of the low solidification rate, bad thermal strength, crack sensitivity and low casting temperature[2,3].The superheat of the molten steel has a great impact on the erosion of refractory lining, molten steel fluidity and non-metallic inclusion behavior[4]. The serious erosion situation of ladle lining, nozzle and casting tundish will give rise to more inclusions at a high superheat. Meantime higher superheat will make second dendrite arm spacing coursing and element segregation which lead to inclusion, bubble formation and shrinkage cavity. On the contrary, it is hard for non-metallic inclusions to float up with a low superheat value. Inclusions of 65Mn steel, which produced in different superheat condition by CSP, were studied for the sake of higher slab properties including statistics and EDS analysis."

Jan 1, 2012

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By Joachim Ulrich

The spreading and splashing behaviour of single tin, lead, copper, aluminium and steel droplets impacting on a solid surface were experimentally examined. The droplet impact was observed using a high speed video imaging technique. The onset of splashing and the mass of the secondary droplets of impacting tin and lead droplets was quantified by the weight difference of the droplets before melting and the splat after the impact. The spread factor and the mass of the secondary droplets in dependence of the impact velocity is shown for different droplet materials, initial droplet diameters, target temperatures in ambient air and inert gas atmosphere. An empirical found correlation predicting the transition from spreading to splashing is presented by means of dimensionless numbers.

Jan 1, 1999

By Jesse White, Tyler Salisbury

Research projects contain many stages of development from the conception of an idea to a fullscale commercial operation. The transition from laboratory-scale research to bench-scale roasting can represent a significant increase in complexity and cost, depending on how many variables are being evaluated. Thermogravimetric analysis (TGA) can simulate roasting conditions and produce a small sample for chemical analysis or materials characterization. A simultaneous thermogravimetric and differential scanning calorimetry (TG–DSC) can identify endothermic and exothermic reaction temperatures. Using thermal analysis, some of the process variables can be tested and eliminated such as ore and reagent blends, retention times, operating temperatures, and some atmospheres.

Jan 1, 2015

By Nicola Baldo, Marco Pasetto

"Recycling of tyre rubber in the road pavement, may be one of the best way to reduce waste tires in large quantities and, at the same time, improve some engineering properties of asphalt mixtures. The paper discusses the results of an experimental study, developed in order to analyse the potentialities of crumb rubber from road tyres in bituminous mixtures, using the dry process. Two types of porous asphalt mixtures and reference mixes without rubber were formulated by the traditional Marshall methodology, and mechanically evaluated by means of the Indirect Tensile Stiffness Modulus test, the Creep test (with confinement), and the Indirect Tensile Fatigue Test. Results of this study indicate that the tyre rubber has a positive influence on the performance characteristics, depending also on the grading and volumetric properties of the mix being studied: an interesting increase of the fatigue life, a better stiffness behaviour at lower temperatures and a bigger permanent deformation resistance at high temperatures are guaranteed. Introduction Recycling the rubber from used tyres, in the construction of road pavement layers, is potentially one of the more interesting and advantageous solutions from both the technical and environmental points of view, in order to reduce the total amount of car and lorry tyres to dispose. In road-building techniques, a technology, termed “wet”, for modifying bituminous binders with crumb rubber has by now become well consolidated. There have been numerous scientific studies conducted on this technology and its applications, particularly in the United States, where it has been adopted and codified in specific technical regulations (ASTM D-6114). If the wet process can be considered amply tested, the same cannot be said for a second technology, termed “dry”, which deserves careful study to evaluate its suitability and advantages. In “dry” processes, the rubber is usually used as a partial substitute of aggregate of equivalent grading and mixed with bitumen after integrating the crumb rubber in the lithic skeleton."

Jan 1, 2008

By Guanyong Shi, Zhihe Dou, Cong Wang, Ting'an Zhang, Hongyan Zhang

We prepared the CuCr alloy by thermit reduction-electromagnetic casting. But there are the defects such as stomata and oxide inclusions in CuCr alloy. In this paper, the existing state and distribution of inclusions and stomata in CuCr alloy are systematically analyzed. The alloy was characterized via SEM, EDS and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that: there are three distinct areas: copper-rich areas, chromium-rich areas and the inclusion areas. Inclusions are mainly in the form of stomata and Al2O3 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Then, the composition of phases of the smelting slags and alloy were characterized via XRD. The results show that: the slag consists of Al2O3 and a little of Cr, the alloy consists of Cr, Cu and a little of Al2O3.

Jan 1, 2015

By Uchil Jayagopal, M. Krishna, P .. V. Krilpakara, S. Manjunath

"There have been a pioneering efforts over the last forty years in the development of metal matrix composites (MMCs) as a new engineering materials, having improved properties, light weight characteristics and competitive costs compared to traditional materials. Following recent advancements in casting technology and the use of melt stirring device by foundries, discontinuously reinforced MMCs where prominent alloys are reinforced with particulates or short fibres and the being employed ·in the production of castings targeted for automotive and aerospace application.The ZA-27 alloy has a high strength compared to zinc or alluminium alloys with a lower melting temperature. The main objective of the present research is to study the effect of quartz particles on the mechanical behaviour of ZA-27 alloy composites. The results showed that the ultimate tensile strength, hardness, Young's modulus of the composite gradually increased with increase in the weight percentage of the quartz reinforcement. However overall ductility decreased with an increase in quartz reinforcementIntroductionMetal matrix composite (MMCs) offer outstanding benefits as they combine metallic properties with ceramic properties there by yielding improved physical and mechanical properties.1Among the various type of MMCs particulate reinforced composite are the most versatile and economical2. By suitable choice of metal matrix and particulate system a wide range of properties combination can be obtained such as strength, modulus, fiiction.al resistance, tribological performance and machinability. These composites are capable of replacing conventional alloys in a considerable range of applications. They also offer significant saving in energy and resources"

Jan 1, 2000

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011