Search Documents

By Xianwen Dai

One of the biggest challenges for the gold industry in the 21st century is the presence of copper in gold containing ore bodies. This is because copper consumes large quantities of cyanide. In addition, copper cyanide species are more stable than free cyanide, and hence are problematic in events of tailings spillage. The present paper compares cyanide and thiosulfate leaching for the recovery of gold from a copper containing ore. For cyanide leaching, the extraction of gold using copper cyanide complexes instead of free cyanide was tested in the presence and absence of added ammonia. For the thiosulfate leaching, the effect of the minerals present in the ore on the solution potential and thiosulfate consumption are illustrated.

Jan 1, 2003

By Isabel Lázaro

A detailed study has been undertaken into the electrochemistry of the leaching of chalcopyrite in acidic solutions containing ferric ions. Mixed potential measurements have shown that the maximum potential achievable on a chalcopyrite disk in a ferric sulfate medium lies within the so-called passive or prewave region in the anodic behavior of chalcopyrite. The very low current densities due to the anodic oxidation of chalcopyrite at potentials in the region of the mixed potential has made studies of the initial stages of dissolution difficult. However a careful rotating ring-disk electrode (RRDE) study has enabled data to be obtained for the stoichiometry of the initial dissolution reaction to be obtained. Thus, in addition to the detection of soluble iron and copper as products in this potential region, a soluble sulfur species has also been detected. A comparison of the experimental with the expected collection efficiencies of the products on the ring has revealed that this soluble sulfur species is likely to be thiosulfate. The characteristic transient anodic behaviour of chalcopyrite in this potential region has been interpreted in terms of a rate limiting solid-state diffusion process. Thus, extrapolated rates based on reported measured solid-state diffusion coefficients for the mineral at elevated temperatures have been shown to be consistent with the potentiostatic current-time transients. Furthermore, comparative studies of the anodic characteristics of the copper sulfide minerals covellite and bornite has confirmed their greater reactivity in this potential region. The results of this investigation have been combined with a parallel study of the non-oxidative behaviour of chalcopyrite in order to derive a model for the dissolution process which is consistent with other published studies of the electrochemistry and dissolution of the mineral.

Jan 1, 2003

By Ronald K. Riddle

The processing of lateritic ores in rotary drying and preheating/pre-reduction systems has historically been plagued by problems associated with significant dust generation. These problems include handling issues, kiln capacity limitations, negative impacts on furnace stability, a reduction in nickel recovery and higher operating costs. The dust is formed in the rotary devices during heating and tumbling due to the following three mechanisms: (I) mechanical dccrepitation of the ore as a result of tumbling and attrition, (2) thermal decrepitation during rapid vaporization of internal free and bound water, and the (3) loss of free moisture which functions as a binder. This paper investigates the causes of dust formation, provides methods to reduce dust carryover from the rotary devices, and finally offers methods to recover the dust in the existing pyrometallurgical process. Keywords: Laterite, Drying, Rotary, Dust

Jan 1, 2004

By M. G. Basavaraj, S. Sarkar, G. S. Gupta, P. D. Patil

"Previous experimental study on raceway size hysteresis on two-dimensional cold model showed that the inter-particle and wall-particle friction had a very large effect on the raceway size. Existing literature correlations for raceway size ignore the frictional effects. It has also been shown in the present study that their applicability to the ironmaking blast furnace is questionable. To take into account the effect of friction on the raceway size a stress analysis has been done for the raceway region. Two-dimensional fluid flow equations under turbulent conditions have been developed and solved computationally in order to get the pressure forces. The frictional forces were obtained in terms of stresses. To predict the raceway size a force balance was done for the raceway zone considering the pressure force, the frictional force and the bed weight. The resulting equations from the force balance are able to describe the raceway hysteresis phenomena reasonably well along with the raceway size. A two dimensional experimental set up has been fabricated in order to validate the computer predictions. Predicted values agree well with the experimental values.IntroductionWhen a high velocity blast of air is introduced into a packed bed through a tuyere, a cavity is formed in front of the tuyere. This cavity, formed in the iron-making blast furnace, is called the raceway. Coke tumbles down and bums in this raceway, generating heat and reducing gases for the iron-making process. The raceway is responsible for producing most of the reducing gasses in the blast furnace. In addition, the size and shape of the raceway determines the movement of solids within the blast furnace, the distribution of gases and liquids (slag and metal), setting the location where the primary chemical reactions occur and the temperature profile in the lower part of the blast furnace.Due to the importance of the raceway, many investigators l - 6 have studied it and have predicted the raceway size using the empirical correlations based on experimental (hot & cold) and mathematical models. A number of correlations have been reported in the literature to predict the raceway size by various investigators3 - 6 which are different to each other. Each of the correlations shows a different dependence of raceway diameter (DR) on bed height, particle size, solid density, bed voidage and blast velocity. None of the correlations includes the effect of solid stresses on the raceway size and shape. The magnitude of these stresses will depend on the bulk solids properties (internal angle of friction, wall angle of friction) and the bed dimensions."

Jan 1, 2001

By Nobuyuki Higashiyama, Ikuo Yonezu

"Hydrogen-absorbing alloys containing rare-earth elements are used in high capacity nickel-metal hydride secondary batteries,' hydrogen storage systems for portable fuel cells, and refrigeration systems. New hydrogen-absorbing alloys containing rare-earth elements have also been developed and introduced into these applications. High performance in nickel-metal hydride secondary batteries is strongly demanded because of the remarkable advancements in portable electric appliances. A large hydrogen absorption capacity, high electrochemical reactivity and superior corrosion resistance in an alkaline solution are required for hydrogen-absorbing alloys used in nickel-metal hydride batteries. The aim of this investigation is to improve the performance of conventional LaNi5 type hydrogen-absorbing alloys. For example, Mm(Ni-Co-Al-Mn)„ type hydrogen-absorbing alloys with various non-stoichiometric compositions were developed. In addition, a new process of rapid quenching process was applied for preparing these hydrogen-absorbing alloys in order to improve their performance.IntroductionRecently, the trend in electronic appliances toward portability has increased the demand for high capacity of secondary batteries as power sources. Since nickel-metal hydride batteries were first commercialized in 1990 in Japan, they have become increasingly popular as power sources for cellular phones, portable computers, electric shavers, and other, products.The performance of a nickel-metal hydride battery, such as its discharge capacity, high rate capability, and charge-discharge cycle life, strongly depends on the characteristics of the hydrogen-absorbing alloy negative electrode. Many types of hydrogen-absorbing alloys have been developed so far. For a hydrogen absorbing alloy to be used as the negative electrode material, (1) it must allow a large amount of hydrogen to be absorbed and desorbed in an alkaline solution, (2) its reaction rate should be high, and. (3) it must have long term durability under repeated charge-discharge cycling. However, LaNi5, a typical rare earth-nickel type alloy, shows significant capacity deterioration during repeated charge-discharge cycling. Therefore the first step in its development was to obtain sufficient corrosion resistance of the LaNi5 alloy for its use as an electrode material. A partial replacement of nickel with cobalt and a substitution of the lanthanum- content with misch metal (Mm), a mixture of rare earth elements such as lanthanum, cerium, praseodymium and neodymium, were very useful in improving the charge-discharge cycle life. However, the discharge capacity of the alloy was still not sufficient for a practical battery. A study of the effect of the partial substitution of aluminum and manganese showed that the best alloy composition was Mm(Ni-Co-Al-Mn)x, as follows.The stoichiometry x of Mm(Ni-Co-Al-Mn)x largely affects the discharge capacity and cycle life. Theose alloys with non-stoichiometric alloys with the compositions of [Mm(Ni-Co-AMn)x: 4.7<x<4.8] have a large capacity and a long cycle life. Nogami' et al. reported that 'a non-stoichiometric alloy with a Mm(Ni-Co-Al-Mn)x (x=4.76) composition showed approximately 10% higher discharge capacity than the stoichiometric alloy (x=5) [1] and greater influence of x on the electrochemical properties of multi-component AB„ type hydrogen-absorbing alloys for batteries."

Jan 1, 2000

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC&apos;s) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Jin Zuomei

The kinetics of dissolution of nickel matte in the presence of manganese dioxide with silver ions was investigated. The catalytic silver ions enchanced the leaching rate up to a factor of 17. The effects of stirring, temperature, particle size, concentrations of Mn02, silver and ferric ions, and the experimental procedures were studied. Solid residues at various levels of nickel extraction were examined by SEM, TEM, electron micoprobe and X-ray diffraction. These results indicated that the dissolution reaction was topochemical and fits a surface reaction control model. The activation energy was calculated to be 39.15 KJ/mol. The leaching rate of Ni3S2 was independent with stirring rate, but the reaction rate constant was inversely proportional to the initial particle diameter. The order of the reaction rate are 0.41, 0.69, 0.33 with respect to Ag+, Mn4+ and Fe&apos;+ con-centration respectively. Thus a kinetic rate equation was developed. Moreover, we propose a mechanism of silver catalyzed leaching of Ni3S2&apos;

Jan 1, 1990

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999

By Bruce W. Downing

MagPower has developed methods to control the detrimental formation of hydrogen that occurs in electrochemical reactions in numerous commercial applications such as the Magnesium-Air Fuel Cell, electrowinning, zinc alkaline batteries, hydrogen embrittlement, waste water/ metal recycling and coolants. The company?s approach to an alternative energy source is the development of an environmentally friendly non-toxic alternative power source that generates electricity through a combination of magnesium, oxygen and a saltwater electrolyte with MagPower?s patent pending hydrogen inhibitors. The magnesium-air technology has never reached the commercial stage due to its limiting power output caused by hydrogen generation. MagPowerhas solved this problem and has patents pending on its intellectual property; the Hydrogen Inhibitors and has developed several consumer power units for a variety of applications through licensing agreements. The company has also shown that the inhibitors have an impact on zinc electrowinning through laboratory test work where current efficiency was improved. This will significantly reduce power consumption and increase the efficiency of the electrowinning process, as well as reduce the potential acid mist hazards associated with electrowinning.

Jan 1, 2003

By Osamu Iida

In the Mitsubishi converting furnace (C-furnace), molten matte continuously undergoes intensive conversion into blister, and an excess amount of heat is generated, even after taking into account heat loss from the furnace, off-gas, and latent heat of melt. To absorb excess heat in C-furnace, recycled granulated converting slags (C-slag) were wastefully charged in the C-furnace. In contrast, supplementary coal is necessary to make up a shortage of reaction heat in Smelting furnace (S-furnace). To utilize the excess heat of the C-furnace effectively and accommodate the unbalance of heat utilization between S and C furnaces, three technological innovations had been carried out. ? Spent anode charging facilities in C-furnace was modified, in order to solve some spent anodes hitting and eroding the hearth bricks. ? Cubic pressed copper scrap charging facilities were installed in C-furnace. ? Facilities were newly installed in C-furnace to treat neutralized residue from the wastewater and dust treatment plants, previously treated in the smelting furnace. Above innovations led to the further effective utilization of heat, increase in production, and savings in energy costs.

Jan 1, 1999

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By R. Moreau, V. Uspenski, K. Messadek, Y. Delannoy

Experiments and numerical simulations have been carried out to investigate the properties of quasi-2D turbulence. A new mercury model experiment has been built and tested in a uniform magnetic field up to 6T, (Ha~ 1000), ensuring a better two-dimensional behaviour than earlier versions (Alboussiere et al., 1997), limited to 0.2T. The quality of the experimental results has been improved in order to get wave number spectra (instead of frequency spectra) and higher signal over noise ratio (due to the higher magnetic fields). In parallel, some two-dimensional "direct" numerical simulations were performed using a commercially available code to solve a 2-D motion equation involving a source term to model the Hartmann layer. This term is derived from the condition of closure of the electric current, which allows to transfer the Hartmann effect into the 2D-core flow without simulating the layer itself (Sommeria & Moreau, 1982). No subgrid scale modelling is needed in such a two-dimensional situation where most of the energy is carried by the large scales.

Jan 1, 1999

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

By Larry Southwick

In the early 1940&apos;s, the Caron ammonia ? ammonia carbonate leach process was used to produce nickel from Mayari ores at the Nicaro plant in Oriente Province, Cuba. While plant operation was generally successful, it was not broadly economical and was shut down. The plant was later restarted in the 1950&apos;s and a number of investigations initiated to resolve the more serious operational and performance issues. Processing steps studied included iron reduction (chemistry ? nickel and iron, reductant, equipment), ore variability (homogeneity and consistency of mineral concentrations, serpentine vs. laterite), leach solution strength, nickel recovery (temperature ? reduction and leaching, reoxidation) and a variety of other topics. These studies and their findings will be discussed. Caron himself obtained good results on these ores in the laboratory. They could not be duplicated in the field, the reasons for which will be reviewed. (Note: the ore looked like garden dirt; charcoal made from palm trees was one of the reductants attempted; and ammonia was the leach solution. Mixing the three, so to speak, was to yield nickel.)

Jan 1, 2006

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By M. A. Barron, D. Y. Medina, R. T. Hernandez, I. Hilerio

"Chromium Nitride (CrN) thin fihns were deposited on steel AISI 316 substrates with reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a d.c. source. At the second coating was applied a negative substrate bias voltage. X ray diffraction, quantitative energy dispersive and scanning electron microscope, were employed to characterize their phases, chemical composition and microstructure. Additionally microhardness was evaluated using a microhardness tester. The results show that the phase formation of CrN thin films in the first case (with temperature) is better. Both coatings presented homogeneous surface. Their compositions shows differences though that gases flow are same. In attention to their hardness, presents an increment if it's compared with hardness substrate.Nomenclature.P Ar =Argon gas pressure during coating.PN2 = Nitrogen gas pressure during coating.Ts = Substrate temperature during coating.T f = Coating melting temperature. (CrN = 1050°C).E=Potential difference.t =Coating time.P=Target power (Cr) in magnetron sputtering de.HV = Vickers hardness.F = Applied charge.d= Average length of longitude of the two diagonals (mm)Introduction.Wear causes losses in materials surface, generating that components of mechanical systems suffer irreversible changes in their properties, causing a faulty operation of the system. It is important to control their effects, measuring and interpreting their causes clearly."

Jan 1, 2013

By Daniel Helm

The first industrial application of direct solvent extraction of nickel from hypersaline sulfate feed solutions has highlighted the need to investigate the influence of chloride on the extraction behaviour nickel in the presence of calcium using Versatic 10 and the solubility characteristics of gypsum. Temperature-solubility curves for gypsum in various aqueous electrolytes were prepared. The solubility of gypsum is increased significantly by the presence of sulfate ions, while chloride ions decrease it for a given temperature. The anion effects of chloride and sulfate on the extraction of calcium and nickel by Versatic 10 corresponded well with the complexing ability of the anions. It was shown that the presence of chloride shifts the extraction isotherms for both metals significantly to the left, while decreasing the selectivity of Versatic 10 for nickel over calcium. The loading of nickel onto Versatic 10 in this system was shown to be at a maximum within 3 seconds, while calcium extraction took between 4 ? 5 seconds to load to a maximum. Chloride ions had no influence on loading kinetics of nickel, but depressed the rate of calcium loading. It was shown that in the presence of an excess of nickel, calcium loading is effectively eliminated, and that calcium is scrubbed from Versatic 10 within 2.5 seconds of contact with nickel electrolyte.

Jan 1, 2003