Search Documents

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By Daudi R. Waryoba

Keywords: Wire Drawing, OFHC Copper, Recrystallization, Orientation imaging Microscopy (OIM), Texture inhomogeneity Textural inhomogeneities have been investigated in oxygen free high conducting (OFHC) copper wire drawn at room temperature to a true strain of 2.31, and isothermally annealed at 250°C and 750°C for annealing times ranging from 10 s to 1 hr. Local orientations were mapped by means of orientation imaging microscopy (OIM). The microtexture of the drawn wires showed a strong <111> + weak <100> duplex fiber texture at the inner core, whereas the mid and surface regions had a comparatively weak texture. Annealing at 250°C resulted into a recrystallization which originated from the mid section, proceed towards the surface regions and ends in the inner core. Recrystallization resulted into a strong<100>+weak<111> duplex fiber texture. A similar textural inhomogeneity was observed during short annealing at 750°C. However, prolonged annealing gave rise to abnormal grain-growth that proceed from the inner core to the outer surfaces with a dominant <111> fiber component at the inner region and mixed components of <111>, <100>, and <112> at the outer surfaces.

Jan 1, 2005

By Na Wang, Chao Du, Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Niobium aluminides were directly synthesized by a sodiothermic reduction process of NbC15 - AlCb which was dispersed into LiCl - KCl - NaCl - CaCb melts. The melt supplied a homogenous reaction medium which was substantially beneficial to the co-reduction of Nb and Al to form niobium aluminides in situ. The reduction was performed at 500°C for 4 hours. The products were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The corresponding results indicated that niobium aluminides powders were successfully synthesized.1. IntroductionNiobium aluminides have received considerable attention as high-temperature structural materials, due to their high melting points, relatively low density, high strength, excellent oxidation and creep resistance [1-4]. Figure 1 shows that there are three intermetallic compounds in the Nb - Al binary [5], which includes Nb3Al (A15 structure, Cr3Si type), Nb2Al (D8b structure, cr-CrFe type) and NbAb (D022 structure, TiAb type). These niobium aluminides have been used in turbine blades or in stationary gas turbines [6-8]. However, despite their attractive features, the ir applications are still limited by the long and costly fabrication process [9, 10].Niobium aluminides were industrially fabricated by the mechanically alloyed process [11-13]. Traditionally, niobium is extracted from Nb2O 5 or K2NbF7 by a metallothermic reduction process while aluminum is produced by the Hall-Heroult process of Ah03 electrolysis. Based on the extraction of Nb and Al, respectively, niobium aluminides is synthesized by a mechanical powder alloying process. The present process for making niobium aluminides requires a set of complicated equipment, has high production cost and time consuming [14, 15].The purpose of this work is to present the simple, economic and direct synthesis of niobium aluminides powders utilizing a sodiothermic reduction from NbC15 - Al Cb dispersed into molten salts."

Jan 1, 2011

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By P. Maraboutis

Iron removal by precipitation as jarosite from Fe-Ni-Co sulfate solutions, (synthetic or real, resulting from laterites leaching) has been investigated. Precipitation was carried out at 95 C, and at an initial pH 1.6, which was either kept constant with CaCO3 or Li2CO3 additions, or left to drift with the evolution of the reaction to lower values. The precipitation of K-, NH4- and Na- jarosite was initially examined using synthetic solutions. In all cases, hydronium ions were incorporated into the precipitate as well. Residual iron in solution was lower (0.2-1 g/1) and equilibrium was achieved faster (within 4-8 h) when precipitating K¬jarosite at constant pH, using CaCO3 for neutralization. Nickel and cobalt losses were small. Na- jarosite precipitation was also studied from real solutions with high initial iron content, under constant pH=1.5, controlled with CaCO3 additions, and it was shown that low residual iron concentration in solution (0.3-0.5 g/1) can be achieved again, with relatively small nickel and cobalt losses. The thickening and filtration characteristics of the precipitates were excellent in all cases examined.

Jan 1, 1988

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By H. Y. Sohn

The considerable progress made in the sulfide smelting technology since the first International Sulfide Symposium of 1983 is discussed. The new developments and innovations have largely been driven by the recognition of environmental concern as well as the need for increased productivity. The smelting technologies for various nonferrous metals are reviewed, with an emphasis on the industry trend towards larger plants and continuous processes. The tremendous advances made in process modeling and computer simulation to describe the complex smelting processes are also reviewed. The goal of these mathematical models is the quantitative description of the processes and the reactors that will provide a means for the control and optimization of smelting operations as well as the optimal design of the operating conditions and the reactors. Environmental issues remain a key consideration in the smelting industry. One of the most remarkable improvements made in the last fifteen years since the 1983 Sulfide Smelting Symposium is the rapid increase in the sulfur capture by nonferrous smelters. This and other related issues are briefly discussed. Finally, the challenges that the smelting industry faces as the new millenium approaches are discussed. The industry continues to face technical challenges to improve productivity and efficiency, while being responsive to ever-increasing public pressure for environmental protection. It also faces external challenges from factors that may cause the reduction of metal uses as a result of substitutions by other materials. Another serious challenge and dire consequence that the primary metals industry is expected to face is the serious diminution of university-educated manpower as well as basic-research output. To remain competitive and healthy, the industry should take up the void left by the complete disappearance, at least in the U.S., and the reduction in other nations, of the governmental support of higher education and basic research in the field of primary metals production.

Jan 1, 1998

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By Aline Maria dos Santos Teixeira

Serpentinite is an ultra basic and metamorphic rock consisting mainly of magnesium, calcium and silicon oxides. The rock under study is a host rock of chromite mine located in Andorinha, BA. The objective of this paper is to evaluate the rock&apos;s physical and chemical characteristics to be used as an additional fertilizer of acid soils. After comminution, rock samples were submitted to chemical analysis, XRD, SEM-EDS and TGA. Afterwards, particle size distribution was determined. Result analysis confirms that our rock consists mainly of dolomite, calcite and diopside. According to the result obtained, it can be said that the serpentinite rock has promising applications in agriculture for the correction and additional fertilization of acid soils. However, it is necessary to study the characteristics of the rock such as its dangers and toxicity as well as evaluate them according to the legislation for corrective acidity.

Jan 1, 2010

By J. D. McCain

Magma&apos;s San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012