Search Documents

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By Jari Aromaa, Olof Forsen

"Oxygen evolution by decomposition of water is the main anodic· reaction in sulphuric acid solution. Traditional anode materials have been relatively low-cost lead alloys, though the active lead dioxide layer has a high oxygen evolution overpotential. This causes a significant increase of cell voltage. To lower total energy use in metal production, electrocatalytical properties or corrosion resistance to decrease replacement costs must be improved. Addition of an catalyzing ion will decrease oxygen evolution potential. The effective area of an anode increases by calcium additions and by producing anodes with fine microstructure. Remelting and rapid quenching is possibly a method that is economically feasible and technically simple enough to be adopted.IntroductionPermanent anodes are widely used in several electrochemical processes and cathodic protection applications. The permanent or ""inert"" anodes can be either massive or coated anodes. The massive anodes are metals, like lead alloys, or non-metals, like magnetite, graphite or ferrite. The coated anodes are made of a valve metal base (titanium, niobium or tantalum) coated with an electrochemically active coating. The purpose of anodes is to supply current to the electrochemical cell. A vast number of materials and their combinations are electrical conductors and may hence be used as anode materials. However, good anode materials must survive in aggressive environments and also be able to pass high current densities. These opposite requirements restrict the amount of possible materials. Generally, an useful anode material must meet three requirements, electrical conductivity, electro catalysis and stability. Good electrical conductivity is essential for energy efficiency. Good electrocatalytical properties are essential to improve product yield. Long term stability is also an important property, because electrode wear and corrosion may cause product contamination, increasing energy consumption and material and labor costs due to need of periodical maintenance. Electrical conductivity and electrocatalytical properties are more widely studied subjects than long term stability of anodes, and a good amount of information about these two subjects can be found in the open literature. Wear and corrosion mechanisms of the anodes vary depending on the operational conditions, i.e. concentration of different species, temperature and operating current density."

Jan 1, 1997

By Zhongming Ren

"A new process of near net shape continuous casting of metal pipe has been put out. The specialty of the process is that no inner core is used. The principle of the process has been presented, and the effect of several factors on the thickness of the pipe has been investigated experimentally and numerically. It is shown that the temperature and the level of the molten metal, cooling intensity of the mold, and the velocity of casting influenced the thickness of the pipe apparently. In order to improve evenness of the thickness of the pipe, the mold was dedicatedly designed, and special methods were taken. By this process, a metallic material like ""bamboo"" was fabricated.IntroductionMetal pipe is a widely used material. Up to now, many processes have been put out to produce the pipe. However, the processes are usually expensive and inefficient. For instance, the welding pipe, which is most widely used, is produced through continuous casting of slab, rolling of the slab into sheet, and welding, with several times of heating and processing. Continuous casting of pipe can not produce small diameter of pipe, which is mostly needed, due to the inner core. Even though. OCC process is novel in fabricating the pipe with small diameter, it is inefficient. In this paper, the no-inner core continuous casting of pipe was proposed. With this process, pipe with small diameter can be produced efficiently. The influence of several parameters on the thickness and evenness of piper wall. With this process, a ""bamboolike"" pipe was fabricated.ExperimentThe experimental apparatus is shown in Fig. I. It is composed of mold, furnace, melt level adjuster, and dummy pipe. In the process, the level of the melt was adjusted at a proper position, then the mold along with the dummy pipe was inserted into the melt in a certain depth. The melt in the mold began solidifying, forming a solid shell. After that, the dummy pipe was pulled upward in a certain speed, drawing the solid shell out of the mold. Thus, a pipe was continuously cast."

Jan 1, 2000

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994

By Andrey Tarasov, Erki Unn, Valery Paretsky

"The stability of the markets of energy resources and labor in countries of the Baltic Sea Region including Estonia is determined to a significant degree by the use of combustible shales as fuel and their distillation resulting in generation of up to 70% of non-recyclable waste. The objective of this business plan is to substantiate the investments for establishment of a new facility in Estonia for waste-less and environmentally safe processing of fossil minerals and man-made products generated in the shale industry, as well as other hazardous wastes. The proposed facility will use a basically new waste processing technology developed in Russia - i.e., processing in sparged molten slag This technology eliminates any release of harmful pollutants to the environment and a facility using this technology does not require, therefore, any sanitary protection zone.IntroductionIn the Baltic region, and first of all in Estonia and some other European territories, there are large natural deposits of combustible shale, which due to the lack of other own resources of energy and hydrocarbons for the chemical industry is burned and distilled with low technical and economic efficiency generating large amounts of toxic and highly toxic wastes and intermediate products. Currently, the penalties for disposal of such wastes have grown to such an extent that shale burning and distillation might become unprofitable. This might result in suspension of the given operations, which in turn will affect in an adverse way the markets of energy resources and labor market in those countries. Furthermore, in addition to the “shale problem”, Estonia, similarly to most member countries of the European Union, faces the challange of environmentally safe processing of highly toxic wastes, such as municipal solid wastes, oilpolluted materials, medical wastes and infected materials, spent rubber tires, etc. These wastes are at present stored or processed with release of a significant quantities of extremely toxic cancerogenic substances (dioxins, furans) or collected and exported for treatment at an extremely high cost and with a loss of valuable components contained in these types of waste and often with return of supper toxic processing products."

Jan 1, 2008

By Viktor Mukhin

"Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose.In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a fullscale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon.During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.).Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.IntroductionSorption technology based on active carbons use starts being applied in such an important in the widest sense of the word strategical branch of economics as non-ferrous metallurgy. Thus since the middle ninetieth Russian gold extraction industry began to apply widely the processes of sorption from pulps and solutions by means of high-resistant granulated active carbons. That provided the start of gold ore minefield exploration, increasing of gold extraction from the ore and reducing its loss with the ""tails"" of process. At present more than 40% of Russian gold is extracted with the help of sorption technologies [1].Another field of active carbons application in non-ferrous metallurgy is the processes of non-ferrous ores floatation at ore-mining and processing enterprise. For that purpose powdered (less than l00µm) active carbons are used for providing the effective selection of minerals with similar physicochemical properties. This method not only increases the metal extraction level but provides deeper division of them."

Jan 1, 2008

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Chikabumi Yamauchi, Masami Tashiro, Toshiharu Fujisawa, Hiroyuki Snano

"Rare earth metals usually contain large amount of oxygen because of their reactiveness, and therefore oxygen removal is one of the major problems on the purification of rare earth metals. In the present research work, halide flux treatment at high temperature under inert gas atmosphere was applied to the oxygen removal from neodymium. NdF3 was used as a halide flux. Deoxidation reaction and its mechanism were discussed based on the experimental results. Halide flux treatment is very effective for oxygen removal from rare earth metals.IntroductionSolid Sate Electrotransport (SSE) process has been successfully applied for the elimination of interstitial gaseous impurities from chemically active metals[l]-[5]. However, to achieve a higher effectiveness of the SSE process, it is required a very low initial impurity content in the metal. In case of rare earth metals, it is known that they usually contain large amount of oxygen that should be lowered as much as possible before applying the SSE process. In addition, if effective oxygen removal is achieved by simple process, it is significant also from the industrial viewpoint. In the present work, the application of a halide flux treatment is investigated to remove oxygen from neodymium by using NdF3 as a flux. At first, deoxidation reaction and its mechanism were discussed based on the phase diagram of the Nd-NdF3-Ndp3 quasi-ternary system. Based on the results, oxygen content in deoxidized neodymium was calculated theoretically and it was verified by deoxidation experiments."

Jan 1, 1998

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By F. Begazo

The most common approach to increase production in copper refineries is to increase current densities. However, if these increases are not well thought out beforehand and are not properly and effectively controlled, the end results could be reduced plant performance and a deterioration in cathode quality. Both of these factors result in lower efficiencies and increased costs. At the Ilo Refinery of Southern Peru Copper Corporation, a modernization and expansion program was implemented shortly after the Refinery was purchased from Minero Peru, in 1994. This program was intended to increase production from 195,200 mtpy of cathode to 227,000 mtpy over a 3-year period. Part of this production increase would come from increasing current density. During the period from 1994 to 1997, current density at the Ilo Refinery was increased from 218 A/m2 to 230 A/m2, while plant efficiencies were maintained at consistently high levels. The current efficiencies were maintained at >97.5% and time efficiencies were maintained at >98%. During 1998, additional increases in current density were implemented while the high plant performance was maintained at the same levels. By the end of 1998, the current density was 241 A/m2, while current efficiency and time efficiency of 98% were maintained. This paper describes the control processes used at the Ilo Refinery to maintain high plant performance levels while increasing the current density. Additionally, expected plant performances from extended test programs at current densities up to 280 A/m2, for future production increases, are reviewed and discussed.

Jan 1, 1999

By J. G. Reid

Nickel is second only to aluminium, of all non-ferrous metals, in energy required to convert the ore to metal. Nickel Laterite ores, which constitute the feed source for approximately 40% of world nickel production, are at a particular disadvantage because of the absence of sulphur, as an energy source, in the ore and because lateritic ores general 1 y are not amenable to beneficiation. The dramatic escalation of oil prices which commenced in 1973 and continued for a decade meant that Nickel Laterite refineries using oil as a primary energy source were placed at a distinct disadvantage relative to refineries utilizing nickel sulphide concentrate feeds. By the late 1970&apos;s the continuing large difference in oil and coal prices caused Greenvale to consider converting certain high oil consuming areas of the refinery to coal. These investigations confirmed that the areas of ore drying and power generation, which together consumed 50% of total Plant oil requirements, could be economically converted from oil to coal firing. Construction of the coal conversion facilities commenced in October 1980 and the first ore drying air heater came on line in August 1981. Construction was completed with the commissioning of the coal fired boiler in June 1982. This paper outlines the additions required to receive and utilize coal in ore drying and power generation and how the changeover was completed with minimal process disruption.

Jan 1, 1988

By Kiyoshi Shibata, Jun-ichi Hayashi

"Steel making technology poses strong potentials for environmental protection in three direction. One is pollution control on steel making process itself. Japanese steel industry has cut down various type of emission drastically since 1970's. Secondary, those process technology can be applied to reduce environmental burden in other industrial sectors. One of the successful examples is municipal waste treatment facility. Thirdly, development of high performance steel products, such as high strength steel for automobile body, can contribute to improve environmental performance during their use, based on the concept of life cycle assessment. Some examples of the successful development and future task is discussed.IntroductionsStack and smoke used to be a symbol of energy intensive industry such as steel making. But, scenery of steel works and its surroundings have been completely changed, and steel products have been changing, as well. The steel making industry consumes huge quantities of energy and resources. Variety of technical development have been carried out to reduce the pollutant release. The steel industry in Japan has been making direct and indirect contributions to reducing of various kinds of environmental impacts through development of high-performance process and products: Its potential technical capability accumulated in steel making is fundamental and essential infrastructure for the vein systems of our society. In this paper, the activity of steel making industry for better environment is discussed"

Jan 1, 2000

By F. Kongoli

A computerized thermophysicochemical database is being developed for various processes involved in nickel smelting and converting. This database includes optimized models for slag, matte, liquid and solid alloys in the multicomponent system(s) as applied to batch and continuous nickel smelting and converting processes. This database can be used to quantify the multicomponent and multiphase slag/matte/alloy/gas equilibria, liquidus and solidus surface, tie-lines, solubility and/or losses of nickel and other components in the slag, distribution coefficients, components activities, heat and mass balance, etc. The database also includes optimized models for the viscosity of the slags associated with any of the above processes. Both databases are coupled and this constitutes a very effective method to quantify the effect of each component on several parameters of the smelting and converting processes and to diffuse the confusion that exists in the literature. Several application examples have been given to demonstrate the usefulness of this database for quantitative prediction of the thermophysicochemical properties of the phases involved in actual or developing processes, even in the areas where experiments are difficult or impossible. The considerable cost reduction that results ftom the use of this database as compared to other methods in the improvement of existing technologies or in the development of new ones is discussed along with continuing new developments of this database.

Jan 1, 2002

By Edgar E. Vidal, Keith Smith, James A. Yurko

Beryllium, like many other reactive metals, is extracted from a halide (generally BeF2) using magnesiothermic reduction, also known as the Kroll process. The beryllium is produced in a molten state, which when solidified resemble "pebbles". Although beryllium is used in limited quantities compared to other metals (< 100 Mt/annual), it is a critical material for the nuclear, defense/aerospace, and large science markets because of its unique nuclear and mechanical properties. Beryllium processing has unique environmental, health, and safety concerns which must be handled appropriately in the 21st century from a worker and environmental safety perspective, and must be designed with this first in mind. In 2011, Materion began operations of its new Kroll plant – informally known as the “Pebbles Plant” - in Elmore, Ohio. The plant was majority funded by a U.S. Department of Defense Production Act (DPA) Title III grant, which is a unique government/industry partnership program to, "create assured, affordable, and commercially viable production capabilities and capacities for items essential for national defense." After a twelve year hiatus from primary beryllium production, Materion has reentered its extraction business and has relearned how to make pebbles. The purpose of this presentation is to give an overview on beryllium extraction and discuss some of the unique aspects of building and operating a safe beryllium facility during the production scale-up phase.

Jan 1, 2015

By B. Holleis, M. Potesser, D. Spoljaric, H. Antrekowitsch, A. Hengelmolen

"During the past only an optimization of metallurgical furnaces were done without attention on the burners. Nevertheless, furnaces without burners are impossible to use in the primary and secondary nonferrous metallurgy in an economic way. Since the energy cost is increasing and the environmental protection is becoming a global issue, the burners are in the focus of several investigations and optimizations. One possible way is the combustion by oxygen. By using oxygen, the flame temperature increases and therefore, fuel accordingly money could be saved by having a low amount of harmful substances like NOx in the off gas. This paper describes a new burner system which combusts fuel with oxygen or air by diluted combustion, hence low pollutants in the off gas. Furthermore the effectiveness of the burner characterized by off gas analyses and simulation in the new development chamber, but also practical tests at an aluminum smelter are described.IntroductionIn 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today’s and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Wärme-Institut “GWI” in Essen (Germany) and the University of Leoben, different new burners have been developed."

Jan 1, 2008

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By Wang Youlai

Sichuan province is the richest province for its waterpower resource in China, perfectly suited to develop a high consuming energy industry. Sichuan Aostar Group Company has two Aluminum smelters, Guangyuan Aostar smelter and Sichuan Aostar Smelter. The production capacity of Aostar Group was 240,000 tons in 2004. The construction scale of Sichuan Aostar Aluminum smelter is 250,000 tons per year. The first 168 GY-300KA pre-baked anode cells (125,000 tons/year) were put into production in 2003. This company has taken the lead in the use of the transfer gantry technology in China. Besides making the process of calibration the pot shell it has concentrated the efforts to construct cell lining elsewhere. This company also has taken the lead in China for using the EIRICH force mixing and cooling technology as well as in the world for the CP Company?s vertical ball mill technology that produces the pre-baked anodes. The carbon anode system completed its 190,000 tons/year production scale. This is the most advanced technology and the biggest scale pre-baking anode manufacture in China. Since the Sichuan Aostar 300KA cell was put into production, it runs normally and smoothly. Up to now the current efficiency is higher than 94% and the specific energy is only 13300kWh/T-Al.

Jan 1, 2006