Search Documents

By G. Ríos

Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975 the old blast furnaces were replaced by the Outokumpu FSF technology. During the last 30 years, through several expansions and technical modifications, the production has increased up to 300,000 tpy of new copper. This paper describes the developments on the control of impurities that have been made to fit new situations, such as a new artificial gypsum plant, a new electrolyte treatment plant or different secondary materials handling management.

Jan 1, 2006

By K. S. Kumar

FLS miljø, Inc. markets, designs and supplies particulate collection devices for dusts, fumes, and mists; In this paper, the application of both wet and dry electrostatic precipitators (ESPs) in smelting, and roasting plants is discussed.

Jan 1, 1998

By Ignacy A. Lipiec

The advantage of microorganisms used in bioleach systems to conventional chemical reaction systems is that these apply the available energy more precisely where it is needed, either directly onto the mineral of interest or by efficiently catalyzing the production of a reactant. The literature cover the range from empirical models used in describing macro heat balance in heaps to detailed studies relating the micro heat effects of bacteria adhesion energy to the surface of minerals. In this paper, the heat effects are reviewed in a general way describing bioleaching in two macro systems, heap leaching and slurry bioreactors. The micro scale heat effects is the reactions and conditions at the microorganism scale, including the mechanism of leaching and bacterial behavior.

Jan 1, 1998

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By Victor Bredykhin

The report is devoted to the investigation and improvement of processes taking place at contact of large quantities of water insoluble liquid and particles of solid phase in a pulp. Theoretical analysis and simulation of acting conditions have allowed to determine that after attaching of oleophilic particles on the «water-reagent» separation surface the break of a formed complex is taking place according to the reagent volume and for oleophobic minerals along the «solid-reagent» separation surface. As a result particles are selectively treated if the magnitude of the reagent adhesion to the surface of solid phase in water is great. The results of dispersion are influenced significantly by availability of sharp edges on the surface of real particles. They keep tree phase perimeter of moistening. It is possible to fix reagent in the form of lens whose contact angle is significantly smaller in comparison to the thermodynamic angle. In adhesion dispersion the reduction of reagent volume, covering the equal area of particles surface is possible when the reagent is in a pulp in the form of thin films on the «water-gas» separation border. The process is tested in laboratory conditions as well as at pilot concentrating mills in flotation of sulfide ores, non-ferrous metals (copper-molybdenum ore), native sulfur and coal.

Jan 1, 2006

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras, Chuanbing Wei

Bottom blown oxygen copper smelting process developed at Dongying Fangyuan Nonferrous Metals shows many advantages such as flexible feed requirement, high productivity, low energy consumption and high direct copper recovery. However, the weak acid generated during the process is not stable which influences the waste management and continuous operation. The amount of the weak acid is determined by SO3 formed in copper smelting process. SO3 can be formed inside copper smelting furnace and boiler at different conditions. Effects of temperature and oxygen partial pressure on the formation of SO3 during copper smelting process have been discussed thermodynamically. Understanding of the mechanisms for SO3 formation will enable the operation of bottom blown copper smelting furnace to be optimized and generation of the weak acid in the process can be managed. The fundamentals developed in this study can also be applied to other copper smelting processes.

Jan 1, 2016

By Yuzo Hiroshige, Masayuki Kyoi, Tomonori Saeki, Masahide Okamoto, Toru H. Okabe, Yu Miyamoto, Tomohiko Akahori, Takeshi Nemoto

We report Hitachi's approach to establish the recycling process for rare-earth metals in magnet. We have developed a process to disassemble the used electric products to collect the magnets, a process to remove the surface plating film of the magnet, and processes to separate rare-earth metals from the magnet. All processes are operated without chemical solutions in order to minimize the environmental impact due to the waste water emission. For the disassemble process, we have developed an equipment to generate continuous shock on the electric products to loosen screws. A sand blast technique is applied for the plating removal process. Rare earth metals in the magnets are extracted by immersion of the magnets in molten magnesium. The extracted rare-earth metals are separated from Mg by evaporation of Mg. The overall yield of recovery is 86.8 %. The purity of the final rare-earth metal is 98.8 %.

Jan 1, 2014

By Henrlk Gripenberg

To solve the environmental and financial problems of the traditional Rotary Salt Furnace process, a new salt-free method for aluminum dross and scrap melting, ALUREC, has been developed by AGA and its partners, Hoogovens Aluminium and MAN GHH. AGA and Hoogovens Aluminium developed the main process concept and jointly carried out trials on pilot plant scale. Owing to excellent results" the partners decided to jointly erect a commercial scale test plant. The order for the design and erection of the furnace went to MAN GHH. The three companies designed the test plant and began operation in the spring of 1994. The results have been excellent and the process is expected to be a technical and commercial success.

Jan 1, 1995

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012

By Dachun Liu, Wenlong Jiang, Baoqiang Xu, Yongnian Dai, Bin Yang

"In the traditional method for refining of indium, glycerin-KI and glycerin-NH4Cl are used as electrolytes to remove Cd and Tl by electrolytic refining, which produces In with a purity of 99.995%. Large quantities of polluted industrial waste water are the result. It is calculated that the saturated vapor pressure of Cd and Tl are between 1-200 Pa, which is much larger than the vapor pressure of In. Thus, the study of removing Cd and Tl was carried out over the temperature range between 700-950 °C and pressures between 1-15 Pa. After vacuum distillation the contents of Cd and Tl in crude indium could sharply fall below 1 ppm..IntroductionIndium is a is a pale blue and silver white metal, and has high ductility [1-2]. Pure indium is generally used as a raw material to produce semiconductor compounds, fluorescent material and ITO targets [3]. Sublimation, zone melting and electrolytic refining are major methods to produce pure indium from crude indium. Electrolytic refining is the main method to product pure indium at present. High productive efficiency, simplicity of operation and short cycle of production are major advantages. However, glycerin-KI and glycerin-NH4Cl are used to remove Cd and Tl in electrolysis method. Large quantities of polluted industrial waste water are the result[4]."

Jan 1, 2012

By Robert W. Bartlett

"Bioheap pretreatment of sulfidic refractory gold ore prior to cyanide leaching is a promising new technology, especially for low-grade ores that cannot afford to be oxidized by pressure leaching or roasting. When an ore contains both refractory and non-refractory (oxidized) gold, an economic decision must be made whether, or not, to pretreat before cyanide leaching. This choice is more complex than the familiar ore/waste cut-off grade decision. Pretreatment usually increases recovery but delays receiving revenue. Based on choosing the processing route that maximizes the present value of the ore, an equation is developed that computes a ""critical cyanide leachable gold grade"" for determining whether pretreating will be profitable. If the ore's actual cyanide leachable grade, without pretreatment, is above this ""critical grade,"" it will not pay to pretreat. The waste/ore cut-off grade, pretreatment yield (leachable grade after pretreatment), total gold grade, pretreatment operating cost and the project's financial discount rate are parameters in the equation. Results of example calculations are provided. This equation can be used for mine development planning and, when bioheap pretreatment is an available option, for daily operating decisions on individual ore blocks.IntroductionOres that are refractory because of sulfide mineral encapsulation of microscopic gold are becoming important. These ores must be pretreated to oxidize the sulfides to liberate the gold prior to cyanide leaching. The conventional pretreatment process technologies are pressure leaching with oxygen and two-stage fluid bed roasting. However, low-grade refractory ores cannot afford the high operating costs of these processes. And, small mines with limited reserves cannot justify the high capital costs of these processes."

Jan 1, 1997

By Han Ilhan

This paper discusses and describes aspects of a cost effective and safe tailings impoundment selection. In light of the current low metal prices and recent tailings embankment failures around the world, it is becoming extremely more important to develop tailings impoundment design that balance cost efficiency with safety. The paper will present critical design components associated with a tailings impoundment which need to be addressed during the planning phase. Procedures for identifying various tailings impoundment alternatives, and evaluation and selection of alternatives are presented.

Jan 1, 1999

By Kenji Monden

A simple technique is presented to evaluate optical property of biomimetic microlens array (BMA) as an antireflective surface on a polydimethylsiloxane (PDMS) sheet. The integration of these structures is done by a thermoforming process. We have only UV-VIS spectrophotometer for optical evaluation apparatus. The transmittance of the sheet is measured with angled sample holder. The 50 deg. transmittance of 270nm pitch BMA on PDMS sheet increases from 87 to 92% after the moth-eye structure is introduced. The transmittance of 350nm pitch BMA on PDMS sheet increases from 87 to 96% after the moth-eye structure is introduced. The transmittance increases with increasing pitch of BMA. The results obtained using UV-VIS spectrophotometer with handmade sample holder.

Jan 1, 2015

By K. R. Barrett

The cupellation of dore/lead bullion to recover precious metals is one of the oldest metallurgical processes known to man. In recent times this has been carried out in small reverberatory furnaces but the process suffers from a number of disadvantages. A new process has been developed at the Northfleet refinery of Britannia Refined Metals Ltd, which gives much improved performance. The process depends upon the injection of oxygen through a nitrogen shrouded lance at the bottom of the furnace. The lance is consumable and of unique design. Reaction rates are high giving short process time; fuel consumption is low; oxygen efficiency is high and dore recirculation is low. The new process has resulted in substantially lower operation costs.

Jan 1, 1989

By Helena Byrdziak

KGHM Polska Miedz SA, in existence since nineteen seventies, operates three underground mines and three smelters with total production of over 400 000 mtpy of electrolytic copper. Its impact on the environment, very serious in the past, has been gradually reduced. While in general emissions into the air and water have been brought under control, attention recently has shifted to the disposal of wastes and residues. The main streams of wastes are flotation tailings, slags and dust captured from the dedusting systems. Much effort has already been expended and is still being spent to utilize this waste for by-products production or to dispose of it within the process by recycling. The most effective measures taken up thus far, as well as present activities directed at tailings disposal, are presented.

Jan 1, 1997

By Peter J. Koros

The current wave of interest in this topic is the result of increased use of titaniferous ores or ilmenite in blast furnace burdens for the purpose of repairing hearth damage. The titanium compounds that promote deposition of ?patching? materials in blast furnaces are the cause of downstream problems in the steelmaking shops. Steelmakers historically have objected to significant amounts of titanium in hot metal (>0.10 % Ti) for several reasons: 1) accretions caused by the TiC.TiN needles that float out of the iron as it cools in transit and in transfers make the accompanying slag sticky and crusty, causing problems in desulfurization and increasing time and Fe yield loss at the subsequent raking, 2) defensive measures have been taken in treatment, such as use of argon for carrier gas, but without technical rationale for this approach, 3) difficulty in removal of the ladle slag by the raker, with subsequent sulfur addition to the vessel charge, and 4) transfer into the BOF and/or formation of a very corrosive TiO2 containing acid slag during the early part of the BOF blow which, in addition to causing lining damage, results in loss of sulfur removal capability by the vessel slag. Based on a conceptual analysis of the metal-slag-atmosphere interactions during transfer ladle desulfurization treatment, a mechanism is postulated for the apparent effectiveness of the use of argon in reducing the deleterious effect of titanium and an alternate technique, possibly more effective, is proposed. As probably the use of argon causes increased exposure to atmospheric oxidation of the titanium carbonitrides contained in the ladle slag, the same benefit can be obtained by use of either oxygen or an air blast to oxidize the noxious reaction compounds. Validity of the concept has been demonstrated in a pilot plant setting. These issues, and related effects on testing the hot metal, are examined in detail with reference to the literature and plant and laboratory experience.

Jan 1, 2006

By Richard D. Hagni

Reflected light microscopic examination of particles from laboratory experimental copper flash furnaces operated under varied furnace conditions shows that the particles exhibit a wide range in mineral compositions and mineral abundances that correlate with partial pressure of oxygen and concentrate/oxygen ratio. Chalcopyrite, bornite, and digenite are more abundant under low oxygen conditions. With increasing oxygen, metallic copper, delafossite and cuprite become increasingly abundant. The extent of particle agglomeration during flight varies with the furnace. Those products from the larger furnaces exhibit the greater degree of agglomeration. Significant particle fragmentation also is evidenced by cracking and brecciation of some particles.

Jan 1, 1991

By G. P. Swayn

Recycling of dusts produced in a flash furnace by direct injection provides the opportunity to reduce recycle loads to the reaction shaft, lower fuel requirements and possibly increase metal recovery to products. Ausmelt has provided an Ausmelt lance system for injecting dusts collected from the waste heat boiler and electrostatic precipitator units, directly into the slag melt. This has been installed and operated in the Kalgoorlie Nickel Smelter with systems for feeding dust, for firing with oil and air, and for raising and lowering the lance. Modelling and testwork development of dust injection, results of commercial trials and design considerations for further opportunities of the Ausmelt lance system, are discussed.

Jan 1, 1994

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011