Search Documents

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By R. Y. Wan

Thiocyanate was evaluated for gold recovery from low-grade refractory gold ores following biooxidation for an acidic heap leaching approach. One of the important features in using thiocyanate is that the leaching can be performed in acidic media, thus avoiding problems related to neutralization and material handling as leaching with alkaline cyanide. Also, the acidic leaching enables the use of ferric ion or bioleach solution as oxidants. In this study, Newmont-Nevada low-grade refractory sulfidic ore was biooxidized in columns at a particle size of 100% passing 102 mm. Thiocyanate leach on the biooxidized ore sample was performed on both ground samples in pulps and coarse material in columns using ferric ion as an oxidant. The variables of thiocyanate and ferric ion concentrations were compared for effect on leaching. Thiocyanate leach results are encouraging and indicate potential for development of a practical process. Gold extractions by thiocyanate are comparable to cyanide leach. Thiocyanate consumption was higher than cyanide, but was in an acceptable level.

Jan 1, 2003

By V. Bojarevics, K. Pericleous

"A number of different methods have been developed for noncontact electromagnetic treatment of liquid metal and to investigate the melting/solidification processes. Applying AC magnetic field in terrestrial conditions, along with the buoyancy and thermo-capillary forces, results in turbulent flow. The use of a homogenous DC magnetic field allows damping both of the turbulence and the large scale flow at different rates leading to surprising results at some stages. The dynamic interaction of the turbulent flow with the oscillating interface needs to be accounted if it is required to levitate liquid metal of up to few kilograms without the contact to container walls. At the high values of magnetic field some oscillation modes are damped quickly, while others are modified with a considerable shift of the oscillating droplet frequencies and the damping constants from the non-magnetic case. Numerical models are used to investigate behavior of liquid metal suspended in high DC magnetic fields providing microgravity-like conditions with laminar viscosity and heat transfer to the surroundings.IntroductionSince the early Electro Magnetic (EM) levitation experiments [1] in AC magnetic field it became apparent that the levitated liquid metal is prone to oscillation and instability. The EM and electrostatic levitation experiments with liquid metal droplets show difficulties related to confinement stability and a need for complex correction functions to establish a correlation between the measurements and the droplet material properties [2,3]. Intense internal fluid flow is visually observed, apparently being in the turbulent regime for earthbound conditions."

Jan 1, 2012

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handing and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines wil1 be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

By Roma T. Dec

Many industrial wastes may require preliminary processing to change their particle size, density, surface properties or flowability to become more suitable for treatment and recycle. This can be achieved by pressure agglomeration using roll presses. In the following paper an overview of various roll press processing methods like briquetting, compacting, compacting-granulating or densification is presented together with basics of process and equipment design. The emphasis is focused on major factors influencing compaction process and responsible for pressure build up and final product quality. Finally, two examples of roll press application for briquetting of steel plant wastes and compaction of alumina base catalyst tailings are introduced.

Jan 1, 1996

By J. H. de. Visser

The transfer of molten metal in smelting or refining operations is typically performed in open trough-type launders that are constructed of either water-cooled copper troughs or refractory lined steel jackets. This transfer can be either continuous or batch. Batch operations transfer metal through an open launder. The uncovered launder has many operational and environmental drawbacks. In order to improve workplace hygiene, designs have evolved toward ventilated launder covers that .are connected to secondary exhaust systems that use negative pressure under the cover removing fume and hot gases to secondary fume control devices. In smelting operations, a variety of covers have been employed which insulate the launder and contain the fumes and also provide additional heat along the length of the launder through a series of premix or inspiration-type burners that add combustion products to the normal fume load in the launder. Cover designs have proven to be inadequate in that hinged unventilated covers hinder convenient access while heated ventilated covers are costly to maintain. Covers that employ refractory bricks and overhead enclosure-type exhaust hoods have been somewhat successful, but restrict operator movement and require large volumes of exhaust air. An example is given of a cover and off-gas system for launders that is designed to provide superior insulation and heating capabilities, as well: as better control of the fume gases-and ease of maintenance. The cover system must maintain the balance between maintaining launder heat and fume removal. The construction of the covers must be able to withstand high internal temperatures and maintain its structural properties.

Jan 1, 1999

By Don Ibana

The use of solvent extraction (SX) in process metallurgy is particularly attractive as it is applicable to a wide range of solute concentration and pH, and it allows complete separation of chemically similar metals such as nickel and cobalt and the rare earths among others. It is therefore applicable to the processing of low grade and complex ores, which is increasing and expanding owing to the diminishing reserves of quality ores, and this has driven the increasing and expanding use of SX.The current SX technology, however, has inherent limitations owing to the use of mechanical agitation as it induces high shear mixing. Excessive shear produces very fine droplets, and while this favours mass transfer, it also leads to sluggish phase separation. High shear mixing is also known to favour crud formation. All these factors as well as high power and reagents consumptions contribute to poor process efficiency. Electrostatic solvent extraction (ESX) is similar to conventional SX except that mechanical agitation is replaced with electrostatic agitation. In direct contrast to mechanical agitation, it allows the production of very small droplets that can be made to maintain intense motion, which favours mass transfer, without affecting the phase separation. In addition, as it uses an electrostatic field, the power consumption is minimal. Hence, it promises to be a superior alternative to conventional SX mixing although an application of the technique is yet to be achieved.Our work to develop an application of the technique in process metallurgy has now established that electrostatic field has no effect on either the stability of the reagents or the chemistry of the process. A volumetric flowrate that is comparable to that of a conventional sieve plate pulse column is achievable. We have also established that electrostatic fields can be made to yield much narrower droplet size distributions than those of mechanically agitated contactors, and they allow better control of droplet motions, which include oscillation and linear motion and hence, mass transfer. These are significant advancements toward our goal and shall be discussed in this presentation.

By Carlos Ortiz

The Huelva Flash Smelting Furnace was commissioned in September 1975. The Smelter and the Acid Plant were expanded in 1995 to their present capacity of 300,000 tpa new copper equivalent and one million tonnes of concentrate per year. During these years of operational experience, most of the initial practices have been reviewed, process control has drastically improved and main process equipment has been modernised. The fourth Flash Furnace campaign lasted 9 years (1995-2004) during which 8 million tonnes of concentrate were smelted. Increasing sulphur content in concentrates and new environmental requirements imply new challenges for smelters to keep production and operation costs down. This paper is an overview of the modifications and improvements carried out in the 2007 general shutdown in Smelter and Acid Plants. Al

Jan 1, 2008

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By Li Cheng

The SKS copper smelting process was jointly developed by Shuikoushan Mining Corp. and ENFI (Beijing Central Engineering and Research Institute for Non-ferrous Metallurgical Industries) in China. It is a new bath copper concentrate smelting process with oxygen enriched air. The pilot plant testwork was completed successfully in 1993. SKS has demonstrated to be an advanced bottom blown smelting process. This technology got the First Class Prize of Scientific and Technological Progress awarded by CNNC (China National Non-ferrous Metal Industry Corp.) in 1994. The SKS process has significant capital and operating cost advantages. Its environmental and industrial safety and hygiene performance represents a substantial improvement when compared to conventional technologies. The technology has generated great interest in the Chinese metallurgical industry. Feasibility studies and basic designs have been carried out to incorporate in retrofit and green field smelter projects in China and abroad. This paper describes the history of the pilot plant operating data (50 tonnes dry feed/day), and discusses the features of the SKS technology, its application and possible future trends.

Jan 1, 1999

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By Maria Margarida Lima, Maria Lucelinda Cunha, Dora Algarvio

"The main goal of the present work is the quality improvement of the recycled aggregates produced by a construction and demolition waste (C&DW) recycling facility located in Montemor-o-Novo, Portugal. The recycling process was developed on a pilot plant scale with 50 t/h of capacity. Process operations are the hammer mill comminution, magnetic separation and screening.In order to improve the knowledge on the C&DW, a characterization procedure was implemented by hand-sorting, magnetic and density separation on representative samples. On the other hand, to improve the quality of the produced aggregates, the bar screen size fractions were analysed, according to the Portuguese Standard (NP EN 933-1 2000).Wood was identified as the critical contaminant, representing 17% by weight of the total contaminants. Sieving results showed that about 97%, 76%, 56%, 98% and 57% were on the correct size range, which lower results are probably due to the type of screens and/or the material characteristics of the recycled aggregates.IntroductionThe construction and demolition waste problemConstruction and demolition waste (C&DW) is generated by the construction activity, resulting from both, buildings or other structures construction and old structures demolition. As a reference, it can be told that C&DW comprises about 40 to 50% of rubbish (concrete, asphalt, bricks, blocks and dirt), 20 to 30% of wood and related products and 20 to 30% of miscellaneous wastes [1]. In Portugal, C&DW is classified in the LER (Portuguese nick name for the European Waste List), Chapter 17, and includes a diversity of wastes, like concrete, bricks, ceramics, bricks, wood, glass, plaster, copper, zinc, lead, iron, steel, as well as insulation and roofing materials. C&DW stream has several characteristics which make it particularly difficult to deal with and are summarized in the following five items.(1) Lack of information on quantities generated: In Portugal, the C&DW sector has been neglected over the past years, which meant that there are not consistent information concerning the quantities and composition of these wastes yet. Several estimates, based in different assumptions, indicate different results, which may vary from 219 Mt to 10 931 Mt [2]."

Jan 1, 2008

By Tobias Pröll, Bernhard Kronberger, Joachim Rohovec, Werner Hölt, Hermann Hofbauer

"As this is only a first draft, more precise explanations as well as detailed schemes, figures and plots will be included in the final draft. The description og the 100 kW test rig will also be mor detailed as construction is ongoing and will be finished during the summer. Furthermore simulations are to be finished shortly; so details on combustibles and gas concentrations will also be included in the final draft.AbstractOxyFuel combustion is a key technology for the efficient separation of CO2 from fuel combus¬tion (especially coal). Since coal plays a minor role in the Austrian energy mix the application of OxyFuel towards other fuels (biomass, waste fuels) is interesting to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alter¬native fuels is also interesting from a strategic point of view in order to generate knowledge for operation of capture ready cofiring and waste/sludge-incineration plants. OxyFuel uses a synthetic mixture of 02 and recycled exhaust gas where the 02 content may vary. This supplementary degree of freedom allows improved operation especially for low calorific fuels. Heavy fuel oil addition for low calorific combustibles can be omitted when using OxyFuel combustion. Application of alternative fuels (wood, waste wood, municipal waste, sewage sludge) in a 100-kW CFB plant is investigated in combination with process simulation.IntroductionOxyFuel combustion is discussed as one of the key technologies for the efficient separation of CO2 from combustion of fossil fuels (especially coal). Since coal plays only a minor role as primary energy source in Austria, the broadening of the scope towards OxyFuel of other fuels like biomass or waste fuels is necessary to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alternative fuels besides the large coal-oriented projects is interesting also from the strategic point of view. The presented project aims at the generation of knowledge in order to design and operate capture ready cofiring and waste/sludge incineration plants."

Jan 1, 2008

By A. Rohkohl, R. Piillenberg

The QSL plant at "BERZELIUS" Stolberg GmbH in Stolberg, Germany was commissioned in 1990, introducing a new era of lead smelting in the more than 150-year-old history of the lead smelter. The lead smelter in Stolberg has changed its appearance several times during its existence. Therefore, at many locations on the site, old and obsolete buildings and equipment parts can still be seen. They are often located side by side with new modern constructions like the QSL-plant and the mercury removal plant, and reflect the specific contrast between tradition and modern technology. After a brief description of the development of the smelter and its decision to implement the current novel plant, the most recent operating results are reported. Following some modifications to the process and equipment, which had become necessary along with the implementation of the new technology, the plant is in operation today at approximately 30% above its design capacity. These achieved production levels are not restricted by the QSL-reactor but by precedent and subsequent available equipment. The QSL-plant entirely complies with the demands of modern, energy-saving, ecologically compatible lead production technology. Stringent environmental standards are maintained on a continuing basis. The demonstrated viability and flexibility of the overall process permits the operation to adapt quickly to the prevailing economical situation worldwide.

Jan 1, 2000

By V. Ramachandran

ASARCO Incorporated, a large and diverse producer of non-ferrous metals, is involved primarily in smelting and refining of copper and lead. The Company also recovers by-product metals and chemicals produced in the smelting and refining process including selenium, tellurium, silver, gold, platinum, palladium, bismuth, antimony oxide, lead-antimony alloys, and nickel sulfate. The treatment of complex concentrates, containing high level's of impurities, also results in the production of various sludges, drosses, dusts and slags. This paper addresses the interplant and intraplant transfer of these materials between the copper and lead circuits and their subsequent treatment for maximum metals recovery. It also describes the role of ENCYCLB/TEXAS Inc., a subsidiary of Asarco, which treats Asarco's by-products, as well as hazardous and non-hazardous wastes produced by other manufacturers.

Jan 1, 1994